Data Sheet
CONNECTsystem for LINEARlight Flex
LF-xx Flex
Benefits
Universal feeder and connector for
LINEARlight Flex modules with 8mm width
Assembly without tools
Reduced assembly time
Highly shock resistant
Applications
Connect system for LINEARlight Flex
modules, LINEARlight POWER Flex,
8mm width
Technical Operating Data and Ordering Guide
Product
EAN *
S-Unit *
Max Voltage
[V]
25
Max Current
[A]
3
0,15
25
25
3
3
Diameter of Wire
[mm² / AWG]
0,14 / 24
- / -
0,057 / 30
0,057 / 30
Length of Wire
[mm]
500
-
10
150
LF-2PIN Flex
LF-2TERM Flex
LF-CONN-10 Flex
LF-CONN-150 Flex
4008321955326
4008321955357
4008321955333
4008321955340
100
200
200
200
*) EAN: Bag containing 10 pieces
S-Unit: Modules per shipping unit
Technical Features
Feeder LF-2PIN Flex for connection of all
Connection possible at the reel end or at the
LINEARlight Flex width 8mm with the power
supply
Board to board connection of two Flex modules:
cut points
Locking System meets shock and vibration
requirements according to IEC 60068-2-6/27
Use only in indoor applications or in luminaires
LF-CONN-10 Flex for short gaps,
LF-CONN-150 Flex for longer gaps
Allowed operating temperature suited to all
with IP67 rating
Backside of LF-2TERM is self-adhesive
LINEARlight Flex products
Additional cutting possibilities by using the
termination LF-2TERM for all single colour
LINEARlight Flex with 8mm width
LF-xx Flex - 08.12.2009
Page 1 of 3
Drawings
LF-2PIN Flex
Housing
Isolation of Wires
PPS / Polyamide / black
PVC / black/red
LF-2TERM Flex
Housing
Isolation of Wires
PPS / Polyamide / black
LF-CONN-10 Flex
Housing
Isolation of Wires
PPS / Polyamide / black
Aramid Paper / white
LF-CONN-150 Flex
Housing
Isolation of Wires
PPS / Polyamide / black
Aramid Paper / white
LF-xx Flex - 08.12.2009
Page 2 of 3
Safety Information
All components of the CONNECTsystem Flex must be assembled to avoid any stress on the wires and/or board connectors. The
installer must ensure that there is adequate strain relief between the board connection and the wiring.
In order to maintain adequate electrical contact, please refrain from repeat removal, maximum of 5, of the CONNECTsystem Flex.
Installation of LED modules (with power supplies) needs to be made with regard to all applicable electrical and safety standards.
Only qualified personnel should be allowed to perform installations.
The connector has no inverse polarity protection. There will be no electrical function if connector is not well positioned or if polarity
is inverse. Several modules can be damaged (see the respective module data sheet).
The maximum operation current on page 1 may not be exceeded.
The CONNECTsystem Flex is designed for indoor application only. Any unprotected outdoor use is not allowed.
A suitable enclosure IP67 is required if the system is to be exposed to humidity and /or dust. Condensation water in the IP67
enclosure is not allowed.
Especially when used with Linearlight POWER Flex the LF-2TERM can overheat. The maximum temperature measured at the "Up"-
label is 65°C. The LF-2TERM has to be adhered to a thermoconducting surface.
Assembly Information
For electrical connection of the LINEARlight Flex modules open the locker by pulling and place the module in the slot. The "up"
mark of the CONNECTsystem Flex must face towards to front side of the LED module for an electrical connection between the
solder pads and the CONNECTsystem Flex. The CONNECTsystem Flex is locked by pushing locking bar back.
Pay attention to the correct polarity between feeder LF-2PIN Flex and LED module:
- For the feeder LF-2PIN Flex connect the black cable to the '-' pole and the red cable to the '+' pole of the module
Particular attention is required when using the connector for board to board connection: The '+' pole of the first module has to be
connected to the '+' pole of the second module. In case of wrong polarity no light will be emitted and the moules can be damaged
(see the respective module data sheet).
The LF-2TERM can be used at any section cut point intended for it. These points are marked on the module.
Sales and Technical Support
OSRAM GmbH
Hellabrunner Strasse 1
D - 81536 München
Germany
www.osram.com
+49 (0)89 6213-0
Sales and technical support is given by the
local OSRAM subsidiaries.
On our world wide homepage all OSRAM
subsidiaries are listed with complete
address and phone numbers.
Related and Further Information
The new dimension of light
OPTOTRONIC® Technical Guide
OPTOTRONIC® Data Sheets
OSRAM LED systems
New standards for LED control gear
153 S006 GB
www.osram.com/led-systems-downloads
130 T008 GB www.osram.com/ecg-downloads
http://catalog.myosram.com
www.osram.com/led-systems
130 W011 GB
www.osram.com/ecg-download
153 S006 GB
www.osram.com/led-systems-downloads
Datasheets for LF05A, LF05E, LF06P
LF-xx Flex - 08.12.2009
Page 3 of 3
京公网安备 11010802033920号
EEWORLD
