T212A685J006PSC datasheet, PDF

Datasheet> All Categories > Passive components> capacitor> T212A685J006PSC

T212A685J006PSC: DescriptionTantalum Capacitor, Polarized, Tantalum (dry/solid), 6V, 5% +Tol, 5% -Tol, 6.8uF, Through Hole Mount, AXIAL LEADED; CategoryPassive components capacitor; File Size157KB，14 Pages; ManufacturerKEMET; Websitehttp://www.kemet.com

Download Datasheet Parametric View All

T212A685J006PSC Overview

Tantalum Capacitor, Polarized, Tantalum (dry/solid), 6V, 5% +Tol, 5% -Tol, 6.8uF, Through Hole Mount, AXIAL LEADED

T212A685J006PSC Parametric

Parameter Name	Attribute value
Is it lead-free?	Contains lead
Is it Rohs certified?	incompatible
Maker	KEMET
package instruction	AXIAL LEADED
Reach Compliance Code	compliant
ECCN code	EAR99
capacitance	6.8 µF
Capacitor type	TANTALUM CAPACITOR
dielectric materials	TANTALUM (DRY/SOLID)
JESD-609 code	e0
leakage current	0.0003 mA
Manufacturer's serial number	T212
Installation features	THROUGH HOLE MOUNT
negative tolerance	5%
Number of terminals	2
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package shape	TUBULAR PACKAGE
method of packing	AMMO PACK
polarity	POLARIZED
positive tolerance	5%
Rated (DC) voltage (URdc)	6 V
surface mount	NO
Delta tangent	0.06
Terminal surface	Tin/Lead (Sn/Pb)
Terminal shape	WIRE

Preview

Download Datasheet

View All

TANTALUM HERMETICALLY SEALED / AXIAL — MIL-PRF-39003

T110 SERIES — POLAR TYPE, T212 (CSR13)

KEMET standard hermetic sealed T110 Series are desirable for use in high humidi-

ty environments. They are ruggedly built, designed for miniaturized circuitry, and are

especially suited for coupling, bypass, filtering and R-C timing circuits. They exhibit

excellent stability, extremely low DC leakage current, dissipation factor, and

ESR/impedance over a wide temperature and frequency range.

Available in standard EIA capacitance values from .0047-330 µF in ±20%, ±10%, and ±5%

tolerances and working voltages from 6-125 VDC.

Higher CV values in comparable case sizes are available in KEMET T140 Series.

Refer to page 27.

Included in the following Series table is a complete listing of CSR13 qualified MIL-

PRF-39003 capacitors. KEMET is approved to manufacture the S (0.001%/k hrs.)

Exponential & D (0.001%/k hrs.) Graded failure rate levels.

KEMET is now offering low ESR limits in the T110 Series. See ESR chart on page

19. You may order the lower ESR by using Customer Specification 2864 as the last

four digits of the part number.

Effective September 30, 2005, the KEMET T110 Series is RoHS Compliant.

CAPACITOR OUTLINE DRAWINGS

1.50±.250

(38.10±6.35)

1.50±.250

(38.10±6.35)

UNINSULATED

CASE

SIZE

±0.005

±(.13)

±0.031

±(.79)

±0.010

±(.25)

INSULATED

±0.031

±(.79)

±0.002

±(.05)

MAX.

DIMENSIONS — INCHES & (MILLIMETERS)

0.125

(3.18)

0.175

(4.45)

0.279

(7.09)

0.341

(8.66)

0.250

(6.35)

0.438

(11.13)

0.650

(16.51)

0.750

(19.05)

0.135

(3.43)

0.185

(4.70)

0.289

(7.34)

0.351

(8.92)

0.286

(7.26)

0.474

(12.04)

0.686

(17.42)

0.786

(19.96)

0.020

(.51)

0.020

(.51)

0.025

(.64)

0.025

(.64)

0.422

(10.72)

0.610

(15.49)

0.822

(20.88)

0.922

(23.42)

TANTALUM

SERIES

T110, T212 (CSR13)

T111, T213 (CSR91)

T140, T242 (CSR23)

ORDERING INFORMATION*

XXX A 105 K 050 A S

SPECIFICATION

All capacitors are sleeved

unless specified.

CASE SIZE

A/B/C/D

PICOFARAD CODE

First two digits represent significant figures.

Third digit specifies number of zeros to follow.

LEAD MATERIAL

S — Standard

T – 100% Tin (T110, T140 Series only)

CAPACITANCE TOLERANCE

M — ±20%

K — ±10%

J — ±5%

FAILURE RATE**

GRADED

A — Not Applicable

B — 0.1%/k hrs.

C — 0.01%/k hrs.

D — 0.001%/k hrs.

EXPONENTIAL

M — 1%/k hrs.

P — 0.1%/k hrs.

R — 0.01%/k hrs.

S — 0.001%/k hrs.

VOLTAGE

At 85°C

**Part Number Example: T110A105K050AS (14 digits - no spaces)

*For Military Ordering Information, see page 4.

**Failure Rates apply only to military products.

MARKING INFORMATION

Marking: Unless otherwise specified by special order, standard marking of T110 Series capacitor consists of the following:

A, B, C & D CASES

+K 10%

R56 µF

100V

0312

Polarity, Manufacturer’s Identification and Capacitance Tol.

Nominal Capacitance — (µF) (“R” indicates decimal)

Voltage

Date Code (e.g.: 0312)

* For Military Marking, see page 4.

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606 (864) 963-6300

Recommended Resources

Transistor meter circuit c

Old 20W electronic ballast circuit diagram

Multifunctional emergency light maintenance circuit 01

Thyristor pre-regulators for various power supplies

ramp generator circuit

Lithium battery charging circuit diagram using MAX846

[Show Works] [Free Trial of Renesas Electronics MCU Kit] - Sequel to Card-swipe Water Meter: In the last article, I showed off my work, but there is no real information. If you need em4095 information, please QQ me or need to design a schematic diagram. I can't send PCB because my boss has in...; 908508455a DIY/Open Source Hardware

ARM software controls the power on and off problem: Hello everyone, I made a small system using Samsung 2410 and used a power management chip to control the power supply. I can confirm that there is no problem with the hardware design. I hope to contro...; lnb19850110 ARM Technology

1. When the host computer sends 1 to the microcontroller, the buzzer sounds at a frequency of 400ms, when it sends 2, it sounds at a frequency of 200ms, when it sends 3, it sounds at a frequency of 100ms, and when it sends 4, the buzzer is turned off.: The procedure is as follows: #include #define uchar unsigned char #define uint unsigned int uint fre,a; sbit b=P2^3; void init(); void main() { init(); while(1){ if(RI==1){ RI =0; ES=0; switch(a){ cas...; 探索者 Embedded System

Why can't the frequency of the crystal oscillator in multisim be changed?: Why can't the frequency of the crystal oscillator made with gate circuits in multisim10 be changed? [img]http://www.y007.com/dianzijishu/UploadFiles_3209/200705/2007515154739953.gif[/img] I changed th...; longlianxi Embedded System

Please help me analyze the op amp integration circuit: Please help me analyze the op amp integrator circuit. As shown in the figure, the red line is the input waveform, which passes through the op amp integrator, and the yellow line represents the output ...; 194027lm Analog electronics

Ask for a solution: [i=s] This post was last edited by yl20084784 on 2016-7-13 19:10 [/i] Here is a fresh and unconventional post. Purpose: Amplify a signal and then sample it with stm32. Problem: The op amp is powered b...; yl20084784 stm32/stm8

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components