NEW
Ultra Small Surface Mount Coaxial Connectors – 1.4mm Mated Height
W.FL Series – Further downsizing of FL series in response to the market needs.
Occupied Mounting Area
2.0
2.0
s
Features
1. Mounting area of only 3.4mm
2
2. The board mounted receptacle weights only 5.6 mg
3. Accepts high frequency transmission of DC to 6GHz
q
Mated Height Comparison(With U.FL series)
(MAX2.0)
(MAX1.55)
5. Plugs are terminated with ultra-fine Teflon®
4.
insulated coaxial cables
6. Un-mating with a simple tool
W.FL Series
U.FL Series
s
Applications
Mobile phones, Wireless LAN, Bluetooth protocol
devices, PDA, GPS, electronic measuring instruments
and any application requiring high frequency
transmission over coaxial line, where space is limited.
Plug
2.85
Cable
(MAX1.55)
1.4
Dia. 0.81
W.FL-R-SMT-1
Receptacle
* Teflon is a registered trademark of DuPont.
(MAX2.5)
1.4
1.9
2.4
4. Receptacle supplied on tape-and-reel for
4.
placement on the board with automatic equipment
U.FL-LP-040
U.FL-LP-066
U.FL-LP(V)-040
W.FL-LP-040
2004.4
1
sProduct
Specifications
Nominal characteristic
50 ohms
Operating temperature range
-40ç to +90ç
(Relative humidity 90% max.)
DC to 6GHz
Operating humidity
-40ç to +70ç
(Relative humidity 90% max.)
Ratings
impedance
Frequency range
sMaterials
and Finishes
Item
1. Contact resistance
2. Insulation resistance
3. Withstanding voltage
4. V.S.W.R.(Note)
Specification
Center: 20m ohms max. Outside: 10m ohms max.
500M ohms min., 100V DC
200V AC / 1 minute
1.3 max. (Up to 3GHz)
1.35 max. (3 to 6GHz)
Note:V.S.W.R. Measurement System
Note:Measured
as shown on the block diagram below.
Note:Test
connection and measurement setup.
Network Analyzer
Test Set
Test Port
Test Port Cable
D.U.T
Termination
Note1:Cable type connector measurements.
With SMA conversion adapters mated with W.FL plug
at each end of the 100cm long ultra-fine coaxial cable.
Note2:Board type connector measurements.
Mounted on a 50 ohms glass epoxy board.
Measurements were conducted with SMA conversion
adapters attached.
sMaterial/Finishes
Part
Plug
Component
Shell
Insulator
Socket center contact
Shell
Material
Phosphor bronze
PBT
Phosphor bronze
Phosphor bronze
LCP
Brass
Finish/Remarks
Silver plated
Black, UL94V-0
Gold plated
Silver plated
Black, UL94V-0
Gold plated
Receptacle
Insulator
Pin center contact
sPlug
2
2.85
Plugs can be ordered only terminated to the cable.
2
1.15
sHow
to Specify Cable Assembly
Double-ended cable assembly
Single-ended cable assembly
***
L(mm)
L(mm)
q
Ordering Information
q
Standard tolerances for (L)**
(L)(mm)
*L=35
to 200
L=200 to 500
L=500 to 1000
W.FL -- 2LP -- 04N
[ ]
-- A -- (L)
1
2
3
4
5
Standard Tolerance (mm)
±4
±8
±12
±1.5% of (L)
1
Series name
2
Assembly type
3
Cable type
4
Cable color
5
Total length (mm)
L=1000
/
W.FL
LP2: Single ended
2LP: Double ended
04N: 0.81mm dia. ultra-fine coaxial cable
1: White, 2: Black
Length (L)
*Minimum available length (L) is 35mm
**Contact nearest HRS representative if different
tolerances are required.
***Contact Nearest HRS representative if one end
requires preparation.
sReceptacle
BRecommended
PCB Mounting Pattern
0.85
0.3
0.25
0.5
1.3
1.7
2
2.6
1.4
1.3
0.3
1.7
2
SIGNAL TERMINAL
1.3
0.65
GND
GND
No conductive traces in this area
SIGNAL
TERMINAL
PAD
Recommended screen thickness: 0.1mm to 0.12mm
Part Number
W.FL-R-SMT-1(10)
CL No.
331-0482-6-10
Packaging
Reel packaging (2000 pieces/reel)
Weight / EA
5.6 mg
1.5
3
sConversion
Adapters
q
SMA Conversion Adapter (W.FL side jack – SMA side plug)
(10.3)
8HEX
W.FL
SMA
Note:Used for performance measurements only.
The W.FL mating side has lower retention
force than the regular product when mated to
the corresponding part.
Part No.
HRMP-W.FLJ
CL No.
311-0367-3
q
SMA Conversion Adapter (W.FL side plug – SMA side jack)
13.8
6
SMA
Ø6.35
( 4.05 )
5.6
1/4-36UNS-2A
W.FL
Note:Used for performance measurements only.
The W.FL mating side has lower retention
force than the regular product when mated to
the corresponding part.
Part No.
HRMJ-W.FLP
CL No.
311-0368-6
q
SMA Conversion Adapter
( 18.35
6
( 4)
)
5.5
1/4-36UNS-2A
Note:When mating with corresponding part (W.FL-
R-SMT-1) it must be pressed down and held
to make complete connection.
Part No.
HRMJ-W.FLP-ST1
311-0386-8
sReceptacle
Inspection Adapter
q
Used for inspecting the performance parameters of the cable assembly.
12.1
( 7.9 )
( 4.4 )
1
4.2
7HEX
M5∞0.5
Part No.
W.FL-R-1
331-0483-9
Ø6.35
CL No.
CL No.
4
sPlug
Extraction Tool-Used for Un-mating of the plug
( 100 )
40
5)
( Ø1
Part No.
W.FL-LP-N
CL No.
331-0492-0
BPackaging
Specifications- Receptacle
W.FL-R-SMT-1(10)
Embossed Carrier Tape Dimensions
2
1.75
4
Ø1
.5
Center contact terminal
12
5.5
8
Unreeling direction
Reel Dimensions
1.8
Ø1
3
14
Ø21
Ø330
5
京公网安备 11010802033920号
EEWORLD
