HT46R64(56SSOP-A) datasheet, PDF

Datasheet> All Categories > The embedded processor and controller> Microcontrollers and processors> HT46R64(56SSOP-A)

HT46R64(56SSOP-A): DescriptionMicrocontroller, 8-Bit, UVPROM, 8MHz, CMOS, PDSO56; CategoryThe embedded processor and controller Microcontrollers and processors; File Size410KB，48 Pages; ManufacturerHoltek; Websitehttp://www.holtek.com/

Download Datasheet Parametric Compare View All

HT46R64(56SSOP-A) Overview

Microcontroller, 8-Bit, UVPROM, 8MHz, CMOS, PDSO56

HT46R64(56SSOP-A) Parametric

Parameter Name	Attribute value
Maker	Holtek
Parts packaging code	SSOP
package instruction	SSOP, SSOP56,.4
Contacts	56
Reach Compliance Code	unknown
Has ADC	YES
Address bus width
bit size	8
DAC channel	NO
DMA channel	NO
External data bus width
JESD-30 code	R-PDSO-G56
length	18.42 mm
Number of I/O lines	20
Number of terminals	56
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
PWM channel	YES
Package body material	PLASTIC/EPOXY
encapsulated code	SSOP
Encapsulate equivalent code	SSOP56,.4
Package shape	RECTANGULAR
Package form	SMALL OUTLINE, SHRINK PITCH
power supply	3/5 V
Certification status	Not Qualified
RAM (bytes)	192
rom(word)	4096
ROM programmability	UVPROM
speed	8 MHz
Maximum slew rate	8 mA
Maximum supply voltage	5.5 V
Minimum supply voltage	3.3 V
Nominal supply voltage	5 V
surface mount	YES
technology	CMOS
Temperature level	INDUSTRIAL
Terminal form	GULL WING
Terminal pitch	0.635 mm
Terminal location	DUAL
width	7.49 mm

HT46R64(56SSOP-A) Preview

HT46R64/HT46C64

A/D with LCD Type 8-Bit MCU

Technical Document

Tools Information

FAQs

Application Note

HA0003E Communicating between the HT48 & HT46 Series MCUs and the HT93LC46 EEPROM

HA0004E HT48 & HT46 MCU UART Software Implementation Method

HA0005E Controlling the I2C bus with the HT48 & HT46 MCU Series

HA0047E An PWM application example using the HT46 series of MCUs

Features

Operating voltage:

Watchdog Timer

Buzzer output

On-chip crystal, RC and 32768Hz crystal oscillator

HALT function and wake-up feature reduce power

SYS

=4MHz: 2.2V~5.5V

SYS

=8MHz: 3.3V~5.5V

24 bidirectional I/O lines

Two external interrupt input

One 8-bit and one 16-bit programmable timer/event

consumption

8-level subroutine nesting

8 channels 10-bit resolution A/D converter

4-channel 8-bit PWM output shared with 4 I/O lines

Bit manipulation instruction

16-bit table read instruction

Up to 0.5ms instruction cycle with 8MHz system clock

63 powerful instructions

All instructions in 1 or 2 machine cycles

Low voltage reset/detector function

52-pin QFP, 56-pin SSOP, 100-pin QFP packages

counter with PFD (programmable frequency divider)

function

LCD driver with 33´3 or 32´4 segments

(logical output option for SEG0~SEG15)

4K´15 program memory

192´8 data memory RAM

Supports PFD for sound generation

Real Time Clock (RTC)

8-bit prescaler for RTC

General Description

The HT46R64/HT46C64 are 8-bit, high performance,

RISC architecture microcontroller devices specifically

designed for A/D product applications that interface di-

rectly to analog signals and which require LCD Inter-

face. The mask version HT46C64 is fully pin and

functionally compatible with the OTP version HT46R64

device.

The advantages of low power consumption, I/O flexibil-

ity, timer functions, oscillator options, multi-channel A/D

Converter, Pulse Width Modulation function, HALT and

wake-up functions, in addition to a flexible and

configurable LCD interface enhance the versatility of

these devices to control a wide range of applications re-

quiring analog signal processing and LCD interfacing,

such as electronic metering, environmental monitoring,

handheld measurement tools, motor driving, etc., for

both industrial and home appliance application areas.

Rev. 1.80

February 14, 2006

HT46R64/HT46C64

Block Diagram

In te rru p t

C ir c u it

P ro g ra m

E P R O M

P ro g ra m

C o u n te r

S T A C K

IN T C

T M R 0 C

T M R 0

P F D 0

T M R 1 C

T M R 1

P F D 1

P r e s c a le r

P D 6 /T M R 0

P D 7 /T M R 1

S Y S

3 2 7 6 8 H z

Y S

In s tr u c tio n

R e g is te r

M P

R T C

D A T A

M e m o ry

W D T

T im e B a s e

Y S

R T C

O S C

O S C 3

O S C 4

W D T O S C

In s tr u c tio n

D e c o d e r

A L U

T im in g

G e n e r a tio n

M U X

P W

P D C

S T A T U S

P D

P O R T D

S h ifte r

8 -C h a n n e l

A /D C o n v e rte r

B P

P B C

P B

L C D

M e m o ry

L C D D R IV E R

P O R T B

P D

0 /

4 /

5 /

6 /

7 /

P W

T M

M 0 ~ P D 3 /P W

T 0

T 1

R 0

R 1

M 3

O S C 2

O S C 4

O S

R E

V D

V S

O S

C 1

A C C

P B 0 /A N 0 ~ P B 7 /A N 7

P A 0

P A 1

P A 2

P A 3

P A 4

/B Z

/P F D

~ P A 7

C 3

P A C

P A

H A L T

P O R T A

E N /D IS

C O M 0 ~

C O M 2

C O M 3 /

S E G 3 2

S E G 0 ~

S E G 3 1

L V D /L V R

Rev. 1.80

February 14, 2006

HT46R64/HT46C64

Pin Assignment

S E G

O S C

V D

O S C

R E

P A 0 /B

P A 1 /B

P A

P A 3 /P F

P A

P A 0 /B Z

1 0

1 1

1 2

1 3

1 4

1 5

1 6

1 7

1 8

1 9

2 0

2 1

2 2

2 3

2 4

2 5

2 6

2 7

2 8

P A 1 /B Z

P A 2

P A 3 /P F D

P A 4

P A 5

P A 6

P A 7

P B 0 /A N 0

P B 1 /A N 1

P B 2 /A N 2

P B 3 /A N 3

P B 4 /A N 4

P B 5 /A N 5

V S S

P D 0 /P W M 0

P D 1 /P W M 1

P D 2 /P W M 2

P D 4 /IN T 0

P D 5 /IN T 1

P D 6 /T M R 0

V L C D

V M A X

V 1

V 2

C 1

C 2

C O M 0

5 6

5 5

5 4

5 3

5 2

5 1

5 0

4 9

4 8

4 7

4 6

4 5

4 4

4 3

4 2

4 1

4 0

3 9

3 8

3 7

3 6

3 5

3 4

3 3

3 2

3 1

3 0

2 9

R E S

O S C 1

O S C 2

V D D

O S C 3

O S C 4

S E G 8

S E G 9

S E G 1 0

S E G 1 1

S E G 1 2

S E G 1 3

S E G 1 4

S E G 1 5

S E G 1 6

S E G 1 7

S E G 1 8

S E G 1 9

S E G 2 0

S E G 2 1

S E G 2 2

S E G 2 3

S E G 2 4

S E G 2 5

S E G 2 6

C O M 3 /S E G 3 2

C O M 2

C O M 1

P A

1 0 0 9 9 9 8 9 7 9 6 9 5 9 4 9 3 9 2 9 1 9 0 8 9 8 8 8 7 8 6 8 5 8 4 8 3 8 2 8 1

8 0

7 9

7 8

7 7

S E G

N C

S E G

N C

1 0

1 1

1 2

1 3

1 4

1 5

1 6

1 7

1 8

1 9

2 0

2 1

7 6

P A 6

P A 7

P B 0 /A N 0

P B 1 /A N 1

P B 2 /A N 2

P B 3 /A N 3

P B 4 /A N 4

P B 5 /A N 5

P B 6 /A N 6

P B 7 /A N 7

V S S

D 0 /P W M 0

D 1 /P W M 1

D 2 /P W M 2

D 3 /P W M 3

P D 4 /IN T 0

P D 5 /IN T 1

D 6 /T M R 0

D 7 /T M R 1

N C

7 5

7 4

7 3

7 2

1 0

1 1

1 2

1 3

1 4

1 5

1 6

1 7

1 8

1 9

2 0

2 1

2 2

2 3

2 4

2 5

2 6

2 7

2 8

2 9

3 0

3 1

3 2 3 3 3 4 3 5 3 6 3 7 3 8 3 9 4 0 4 1 4 2 4 3 4 4 4 5 4 6 4 7 4 8 4 9 5 0

7 1

7 0

6 9

6 8

6 7

H T 4 6 R 6 4 /H T 4 6 C 6 4

1 0 0 Q F P -A

6 6

6 5

6 4

6 3

6 2

6 1

6 0

5 9

5 8

5 7

5 6

5 5

5 4

5 3

5 2

5 1

S E G

C O M

C 2

C 1

V 2

V 1

V M A

V L C

2 2

2 3

2 4

2 5

2 6

2 7

2 8

2 9

3 0

3 1

3 /S E G 3 2

H T 4 6 R 6 4 /H T 4 6 C 6 4

5 6 S S O P -A

S E G 1

S E G

O S C

V D

O S C

R E

P A 0 /B

P A 1 /B

P A

P A 3 /P F

P A

5 2 5 1 5 0 4 9 4 8 4 7 4 6 4 5 4 4 4 3 4 2 4 1 4 0

S E G

1 1

1 2

1 3

1 4

1 5

1 6

1 7

1 8

1 9

2 0

2 1

2 2

2 3

P B

P D 0 /P

P D 1 /P

P D 2 /P

P A

/A N

V S

W M

3 9

3 8

3 7

3 6

3 5

1 0

1 1

H T 4 6 R 6 4 /H T 4 6 C 6 4

5 2 Q F P -A

1 2

1 3

1 4 1 5 1 6 1 7 1 8 1 9 2 0 2 1 2 2 2 3 2 4 2 5 2 6

3 4

3 3

3 2

3 1

3 0

2 9

2 8

2 7

S E

C O

V 1

V M

V L

P D

A X

C D

6 /T M R 0

5 /IN T 1

4 /IN T 0

G 2

M 3

/S E G 3 2

M 0

M 1

M 2

Note:

The 52-pin QFP package does not support the charge pump (C type bias) of the LCD. The LCD bias type must

select the R type by option.

February 14, 2006

Rev. 1.80

HT46R64/HT46C64

Pin Description

Pin Name

PA0/BZ

PA1/BZ

PA2

PA3/PFD

PA4~PA7

PB0/AN0

PB1/AN1

PB2/AN2

PB3/AN3

PB4/AN4

PB5/AN5

PB6/AN6

PB7/AN7

PD0/PWM0

PD1/PWM1

PD2/PWM2

PD3/PWM3

PD4/INT0

PD5/INT1

PD6/TMR0

PD7/TMR1

VSS

VLCD

VMAX

V1, V2, C1, C2

COM0~COM2

COM3/SEG32

SEG0~SEG31

I/O

Options

Wake-up

Pull-high

Buzzer

PFD

Description

Bidirectional 8-bit input/output port. Each bit can be configured as wake-up in-

put by option. Software instructions determine the CMOS output or Schmitt

Trigger input with or without pull-high resistor (determined by pull-high op-

tions: bit option). The BZ, BZ and PFD are pin-shared with PA0, PA1 and

PA3, respectively.

I/O

Pull-high

Bidirectional 8-bit input/output port. Software instructions determine the

CMOS output, Schmitt trigger input with or without pull-high resistor (deter-

mined by pull-high option: bit option) or A/D input. Once a PB line is selected

as an A/D input (by using software control), the I/O function and pull-high re-

sistor are disabled automatically.

I/O

Pull-high

PWM

Bidirectional 4-bit input/output port. Software instructions determine the

CMOS output, Schmitt trigger input with or without a pull-high resistor (deter-

mined by pull-high option: bit option). The PWM0/PWM1/PWM2/PWM3 out-

put function are pin-shared with PD0/PD1/PD2/PD3 (dependent on PWM

options).

Bidirectional 4-bit input/output port. Software instructions determine the

CMOS output, Schmitt trigger input with or without a pull-high resistor (deter-

mined by pull-high option: bit option). The INT0, INT1, TMR0 and TMR1 are

pin-shared with PD4/PD5/PD6/PD7.

Negative power supply, ground

LCD power supply

IC maximum voltage connect to VDD, VLCD or V1

Voltage pump

SEG32 can be set as a segment or as a common output driver for LCD panel

by options. COM0~COM2 are outputs for LCD panel plate.

LCD driver outputs for LCD panel segments. SEG0~SEG23 can be optioned

as logical outputs.

OSC1 and OSC2 are connected to an RC network or a crystal (by options) for

the internal system clock. In the case of RC operation, OSC2 is the output ter-

minal for 1/4 system clock. The system clock may come from the RTC oscilla-

tor. If the system clock comes from RTCOSC, these two pins can be floating.

Real time clock oscillators. OSC3 and OSC4 are connected to a 32768Hz

crystal oscillator for timing purposes or to a system clock source (depending

on the options). No built-in capacitor

Positive power supply

Schmitt trigger reset input, active low

I/O

Pull-high

1/3 or 1/4 Duty

Logical Output

OSC1

OSC2

Crystal or RC

OSC3

OSC4

VDD

RES

RTC or

System Clock

Absolute Maximum Ratings

Supply Voltage ...........................V

-0.3V

to V

+6.0V

Input Voltage..............................V

-0.3V

to V

+0.3V

Storage Temperature ............................-50°C to 125°C

Operating Temperature...........................-40°C to 85°C

Note: These are stress ratings only. Stresses exceeding the range specified under

²Absolute

Maximum Ratings² may

cause substantial damage to the device. Functional operation of this device at other conditions beyond those

listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliabil-

ity.

Rev. 1.80

February 14, 2006

HT46R64/HT46C64

D.C. Characteristics

Test Conditions

Symbol

Parameter

Operating Voltage

Operating Current

(Crystal OSC, RC OSC)

Operating Current

(Crystal OSC, RC OSC)

Operating Current

SYS

=32768Hz)

Standby Current

(*f

=T1)

Standby Current

(*f

=RTC OSC)

Standby Current

(*f

=WDT OSC)

No load, ADC Off

=0.9V

=0.1V

No load, system HALT,

LCD Off at HALT

No load, system HALT,

LCD On at HALT, C type

No load, system HALT,

LCD On at HALT, C type

No load, system HALT,

LCD On at HALT, R type,

1/2 bias, VL

(Low bias current option)

No load, system HALT,

LCD On at HALT, R type,

1/3 bias, VL

(Low bias current option)

No load, system HALT,

LCD On at HALT, R type,

1/2 bias, VL

(Low bias current option)

No load, system HALT,

LCD On at HALT, R type,

1/3 bias, VL

(Low bias current option)

Conditions

SYS

=4MHz

SYS

=8MHz

No load, ADC Off,

SYS

=4MHz

No load, ADC Off,

SYS

=8MHz

2.2

3.3

0.7V

0.9V

2.7

3.0

-2

-5

0.3

0.6

2.5

3.0

3.3

-4

-8

5.5

0.6

0.3V

0.4V

3.3

3.6

Min.

Typ.

Max.

Unit

Ta=25°C

DD1

DD2

DD3

STB1

STB2

STB3

STB4

Standby Current

(*f

=RTC OSC)

STB5

Standby Current

(*f

=RTC OSC)

STB6

Standby Current

(*f

=WDT OSC)

STB7

Standby Current

(*f

=WDT OSC)

Input Low Voltage for I/O Ports,

TMR0, TMR1, INT0 and INT1

Input High Voltage for I/O Ports,

TMR0, TMR1, INT0 and INT1

Input Low Voltage (RES)

Input High Voltage (RES)

Low Voltage Reset Voltage

Low Voltage Detector Voltage

I/O Port Segment Logic Output

Sink Current

I/O Port Segment Logic Output

Source Current

IL1

IH1

IL2

IH2

LVR

LVD

OL1

OH1

Rev. 1.80

February 14, 2006

More (Only the first 5 pages are displayed. Please Download Datasheet to view the full content.) >

HT46R64(56SSOP-A) Related Products

	HT46R64(56SSOP-A)	HT46C64(56SSOP-A)	HT46C64(52QFP-A)	HT46C64(100QFP-A)	HT46R64(52QFP-A)	HT46R64(100QFP-A)
Description	Microcontroller, 8-Bit, UVPROM, 8MHz, CMOS, PDSO56	Microcontroller, 8-Bit, MROM, 8MHz, CMOS, PDSO56,	Microcontroller, 8-Bit, MROM, 8MHz, CMOS, PQFP52	Microcontroller, 8-Bit, MROM, 8MHz, CMOS, PQFP100,	Microcontroller, 8-Bit, UVPROM, 8MHz, CMOS, PQFP52	Microcontroller, 8-Bit, UVPROM, 8MHz, CMOS, PQFP100
Maker	Holtek	Holtek	Holtek	Holtek	Holtek	Holtek
Parts packaging code	SSOP	SSOP	QFP	QFP	QFP	QFP
package instruction	SSOP, SSOP56,.4	SSOP, SSOP56,.4	QFP, QFP52,.68SQ,40	QFP, QFP100,.75X.99	QFP, QFP52,.68SQ,40	QFP, QFP100,.75X.99
Contacts	56	56	52	100	52	100
Reach Compliance Code	unknown	unknown	unknown	unknown	unknown	unknown
bit size	8	8	8	8	8	8
JESD-30 code	R-PDSO-G56	R-PDSO-G56	S-PQFP-G52	R-PQFP-G100	S-PQFP-G52	R-PQFP-G100
Number of terminals	56	56	52	100	52	100
Maximum operating temperature	85 °C	85 °C	85 °C	85 °C	85 °C	85 °C
Minimum operating temperature	-40 °C	-40 °C	-40 °C	-40 °C	-40 °C	-40 °C
Package body material	PLASTIC/EPOXY	PLASTIC/EPOXY	PLASTIC/EPOXY	PLASTIC/EPOXY	PLASTIC/EPOXY	PLASTIC/EPOXY
encapsulated code	SSOP	SSOP	QFP	QFP	QFP	QFP
Encapsulate equivalent code	SSOP56,.4	SSOP56,.4	QFP52,.68SQ,40	QFP100,.75X.99	QFP52,.68SQ,40	QFP100,.75X.99
Package shape	RECTANGULAR	RECTANGULAR	SQUARE	RECTANGULAR	SQUARE	RECTANGULAR
Package form	SMALL OUTLINE, SHRINK PITCH	SMALL OUTLINE, SHRINK PITCH	FLATPACK	FLATPACK	FLATPACK	FLATPACK
power supply	3/5 V	3/5 V	3/5 V	3/5 V	3/5 V	3/5 V
Certification status	Not Qualified	Not Qualified	Not Qualified	Not Qualified	Not Qualified	Not Qualified
RAM (bytes)	192	192	192	192	192	192
rom(word)	4096	4096	4096	4096	4096	4096
ROM programmability	UVPROM	MROM	MROM	MROM	UVPROM	UVPROM
speed	8 MHz	8 MHz	8 MHz	8 MHz	8 MHz	8 MHz
Maximum slew rate	8 mA	8 mA	8 mA	8 mA	8 mA	8 mA
surface mount	YES	YES	YES	YES	YES	YES
technology	CMOS	CMOS	CMOS	CMOS	CMOS	CMOS
Temperature level	INDUSTRIAL	INDUSTRIAL	INDUSTRIAL	INDUSTRIAL	INDUSTRIAL	INDUSTRIAL
Terminal form	GULL WING	GULL WING	GULL WING	GULL WING	GULL WING	GULL WING
Terminal pitch	0.635 mm	0.635 mm	1 mm	0.635 mm	1 mm	0.65 mm
Terminal location	DUAL	DUAL	QUAD	QUAD	QUAD	QUAD

Recommended Resources

Large range 7~40V to 5VDC-DC step-down circuit diagram

Wattmeter circuit for measuring low frequency amplifier output power

Solarium controller circuit

Control input start charging circuit diagram b

Double core saturation magnetometer circuit

Computer motherboard circuit diagram 815 4_53

Need help designing a voltage sensor?: Parameter requirements: Range: ±20V, Graduation value: 0.01V, Digital tube display, RS232 communication with host computer, 3.7V lithium battery power supply. Please draw the circuit block diagram and...; gaofeng_19901 Analog electronics

A picture I just drew by copying a gourd.: I drew this with reference to the English data. Some values have been slightly changed. Please help check it! I still don’t quite understand what the values of R1 and R2 are calculated based on and wh...; ena Power technology

Design and implementation of digital modulator based on DDS: I am now working on my graduation project, and the title of the thesis is: Design and Implementation of Digital Modulator Based on DDS. If any brother or uncle has any information on this subject, ple...; wywywy7436 Analog electronics

In which .h file is the delay function?: [color=#333333][font=arial, 宋体, sans-serif,]Which .h file is the halMcuWaitUs(uint16 usec) function located in? [/font][/color]...; 初学者2013 RF/Wirelessly

ARM GCC GD32F350RB MCU startup file and connection file sharing: [i=s]This post was last edited by serialworld on 2018-9-13 20:16[/i] I planned to use armGCC to develop GD320, but found that the official did not provide startup files and linker files for GCC. So I ...; serialworld GD32 MCU

Sensorless FOC Video: https://v.youku.com/v_show/id_XNDY3ODYyMzk2MA==.html https://v.youku.com/v_show/id_XNDYzMDEwOTk2MA==.html http://https://v.youku.com/v_show/id_XNDY3NjE2NjM1Ng==.html https://v.youku.com/v_show/id_XNDc...; jie888jie89 Motor Drive Control（Motor Control）

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components