DT22J12G215DQA8 datasheet, PDF

Datasheet> All Categories > Mechanical and electronic products> switch> DT22J12G215DQA8

DT22J12G215DQA8: DescriptionRocker Switch, DPST, Latched, Quick Connect Terminal, Rocker Actuator, Panel Mount, ROHS COMPLIANT; CategoryMechanical and electronic products switch; File Size233KB，4 Pages; ManufacturerITT; Websitehttp://www.ittcannon.com/; Environmental Compliance

Download Datasheet Parametric View All

DT22J12G215DQA8 Overview

Rocker Switch, DPST, Latched, Quick Connect Terminal, Rocker Actuator, Panel Mount, ROHS COMPLIANT

DT22J12G215DQA8 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	ITT
package instruction	ROHS COMPLIANT
Reach Compliance Code	unknown
ECCN code	EAR99
Actuator type	ROCKER
body width	17.78 mm
Body length or diameter	23.88 mm
Contact (AC) maximum rated R load	8A@125VAC
Maximum contact current (AC)	8 A
Maximum contact voltage (AC)	125 V
Electrical life	10000 Cycle(s)
JESD-609 code	e4
Manufacturer's serial number	DT22
Installation features	PANEL MOUNT
Maximum operating temperature	85 °C
Minimum operating temperature	-20 °C
surface mount	NO
Switch action	LATCHED
switch function	DPST
Switch type	ROCKER SWITCH
Terminal surface	Silver (Ag)
Termination type	QUICK CONNECT

Preview

Download Datasheet

View All

DT Series

Miniature Power Rocker Switches

Features/Benefits

Typical Applications

•

Illuminated versions available

•

Small appliances

•

Double pole switching in

•

Computers and peripherals

miniature package

•

Medical instrumentation

•

Snap-in mounting

•

RoHS compliant

Models Available

Specifications

CONTACT RATING:

UL/CSA: 8 AMPS @ 125 VAC, 4 AMPS @ 250 VAC

VDE: 10 AMPS @ 125 VAC, 6 AMPS @ 250 VAC.

ELECTRICAL LIFE: 10,000 make and break cycles at full load.

INSULATION RESISTANCE: 10

Ω

min.

DIELECTRIC STRENGTH: 1,500 VRMS @ sea level.

OPERATING TEMTERATURE: -20ºC to +85ºC

Materials

HOUSING AND ACTUATOR: 6/6 nylon (UL94V-2), black, matte finish.

ILLUMINATED ACTUATOR: Polycarbonate, matte finish.

CENTER CONTACTS: Silver plated, copper alloy.

END CONTACTS: Silver plated AgCdo.

ALL TERMINALS: Silver plated, copper alloy.

NOTE:

Specifications and materials listed above are for switches with standard options.

For information on specific and custom switches, consult Customer Service Center.

Build-A-Switch

To order, simply select desired option from each category and place in the appropriate box. Available options are shown

and described on pages G–67 through G–69. For additional options not shown in catalog, consult Customer Service Center.

Switch Function

DT12

SPST On-None-Off

DT22

DPST On-None-Off

Actuator

Rocker

Two-tone rocker

Illuminated rocker

Actuator Color

1-5

See Chart on Page G-68

Red, illuminated

Amber, illuminated

Green, illuminated

Mounting Style/Color

Snap-in, black

Snap-in, white

Recessed snap-in bracket, black

Guard, black

Termination

.187” quick connect

PC Thru-hole

Right angle, PC thru-hole

Actuator Marking

(NONE)

No marking

ON-OFF

”O l” - international ON-OFF

Large dot

”O -” international ON-OFF

* QF available with termination 15 only.

Rocker

Contact Rating

Silver (UL/CSA)

Silver (VDE)*

Lamp Rating

(NONE)

No lamp

125 VAC neon

250 VAC neon

Dimensions are shown: Inches (mm)

Specifications and dimensions subject to change

G–66

www.ck-components.com

Recommended Resources

A differential line driver circuit diagram

Using NE560B frequency shift keying signal demodulator circuit

Three-phase power factor controller

3V to 6V voltage doubling circuit diagram

Differential flammable gas detection application circuit

555 direct reading capacitance tester circuit

Sandwich resistor structure and its application: [p=30, null, left][color=rgb(17, 17, 17)][font=宋体][font=Verdana]In the design of analog circuits, a special sandwich resistor is often used, but there is little introduction to this resistor. This pap...; fish001 Analogue and Mixed Signal

I use the io port to simulate i2c, and can only read but not write to e2prom. What's going on?: It can be read, which means there is no problem with writing and reading eight bits, and the logic is correct....; wly2018 Embedded System

Verilog implementation of dct (Part 3): Verilog implementation of dct (Part 3)...; 247153481 FPGA/CPLD

The program automatically enters interruption when it starts!: Experts, have you ever encountered this problem: the program automatically enters interrupt after booting, but it is not written in this way! But it is normal after RST! Please advise!...; hanna207 Microcontroller MCU

How to implement the ctrl-Z at the end of sending a text message with tc35: How can I achieve the ctrl-Z at the end of sending a text message with tc35? I need it urgently. Thanks for your help....; mcuer Embedded System

Does anyone know about VoIP or RTC under wince6.0? I have implemented audio intercom using RTC. How can I implement video intercom?: Reference address: http://msdn.microsoft.com/en-us/library/aa921886.aspx How to add the video filter to RTC? I did it according to msdn, but I didn't see the video parameter information in the sdp sen...; shenyu815 Embedded System

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components