EEWORLDEEWORLDEEWORLD

Part Number

Search

KA-D4J

Description
Power/Signal Relay, 4PDT, Momentary, 3360mW (Coil), 10A (Contact), 28VDC (Contact), AC Input, AC/DC Output, Socket Mount,
CategoryMechanical and electronic products    relay   
File Size727KB,12 Pages
ManufacturerEsterline Power Systems
Download Datasheet Parametric View All

KA-D4J Overview

Power/Signal Relay, 4PDT, Momentary, 3360mW (Coil), 10A (Contact), 28VDC (Contact), AC Input, AC/DC Output, Socket Mount,

KA-D4J Parametric

Parameter NameAttribute value
MakerEsterline Power Systems
Reach Compliance Codeunknown
ECCN codeEAR99
Other featuresCOIL OPERATE VOLTAGE(AC): 25.9 V, COIL RELEASE VOLTAGE(AC): 10 V; PANEL MOUNTABLE
body width25.78 mm
body height25.4 mm
Body length or diameter25.78 mm
Coil current (AC) maximum value0.12 A
Coil power3360 mW
Maximum coil voltage (AC)28 V
Coil/Input Power TypeAC
Contact (AC) maximum rated R load10A@115VAC
Maximum contact current (AC)10 A
Maximum contact current (DC)10 A
Contact (DC) maximum rated R load10A@28VDC
Maximum contact voltage (AC)115 V
Maximum contact voltage (DC)28 V
Contact/Output Power TypeAC/DC
Electrical life100000 Cycle(s)
JESD-609 codee4
Installation featuresSOCKET MOUNT
operating hours21 ms
Maximum operating temperature125 °C
Minimum operating temperature-70 °C
physical size25.78mm x 25.78mm x 25.4mm
GuidelineMIL-PRF-83536
Relay actionMOMENTARY
Relay function4PDT
Relay typePOWER/SIGNAL RELAY
release time50.1 ms
sealCORROSION PROOF; HERMETICALLY SEALED
surface mountNO
Terminal surfaceGOLD
Termination typeSNAP-ON
SERIES KA
ENGINEERING DATA SHEET
RELAY - NONLATCH - AC COIL
4 PDT, 10 AMP
115 Vac and 28 Vac, 400 Hz and 50/400 Hz coil voltages
All welded construction
Contact arrangement
Qualified to
4 PDT
MIL-PRF-83536
PRINCIPLE TECHNICAL CHARACTERISTICS
Contacts rated at
Weight
Dimensions
28 Vdc; 115 Vac, 400 Hz, 1Ø and
115/200 Vac, 400 Hz 3Ø
0.155lb max
1.10in x 1.10in x 1.00in
Special models available upon request.
Hermetically sealed, corrosion resistant metal can.
APPLICATION NOTES:
102
007
023
APPLICABLE SOCKET:
SO-1048-8776/8779
CONTACT ELECTRICAL CHARACTERISTICS
Contact rating
per pole and load
type [1]
Resistive
Inductive [3]
Motor
Lamp
Overload
Rupture
Load current in Amps
@28 Vdc
10
8
4
2
40
50
@115 Vac
400 Hz
10
8
4
2
60
80
@115/200 Vac
400 Hz, 3Ø
10
8
4
2
60
80
@115/200 Vac
60 Hz, 3Ø [2]
2.5
2.5
2
1
N/A
N/A
@230/400 Vac
400 Hz, 3Ø [8]
5
5
2
2
N/A
N/A
Featuring
LEACH
©
power and control solutions
www.esterline.com
AMERICAS
6900 Orangethorpe Ave.
P.O. Box 5032
Buena Park, CA 90622
.
.
Tel: (01) 714-736-7599
Fax: (01) 714-670-1145
EUROPE
2 Rue Goethe
57430 Sarralbe
France
.
.
Tel: (33) 3 87 97 31 01
Fax: (33) 3 87 97 96 86
ASIA
Units 602-603 6/F Lakeside 1
No.8 Science Park West Avenue
Phase Two, Hong Kong Science Park
Pak Shek Kok, Tai Po, N.T.
Hong Kong
Tel: (852) 2 191 3830
Fax: (852) 2 389 5803
Data sheets are for initial product selection and comparison. Contact Esterline Power Systems prior to choosing a component.
Date of issue: 07/10
- 101 -
Page 1 of 4
Features and functions of PIC series microcontroller data memory (Part 1)
Although there are many varieties of PIC series microcontrollers, the data memory settings of the internal hardware resources of each product are still very regular. The author takes PIC16C71A and PIC...
rain Microchip MCU
The difference between WinCe 3.0 and 5.0 in speed, the difference between the development tool EVB and VS2005 (VB.NET) program
First time to contact with embedded system. . I don't understand many questions. I checked a lot of information on the Internet, but I still don't understand some of them. The board is: EICB-I, here i...
daxingxian Embedded System
Simple crystal oscillator test
This article introduces a simple and easy-to-make crystal oscillator testing device. The principle circuit is shown in the attached figure. In the figure, V1 and its peripheral components (including t...
zzzzer16 Test/Measurement
DSP+CPLD download program failed
I made a board myself (CPLD and DSP have pins connected together after power on) 1. When I only download the program to one of the chips, it works. (For example, when I download the program to DSP (CP...
zhaironghui DSP and ARM Processors
How to add icons to buttons in WINCE programs
How to add an icon to a button in a WINCE program? I am writing a WINCE program. I have seen that in some WINCE programs, the button is an icon. How can I make it so that when I click the button, a cl...
pipingtom Embedded System
LM5017 Reference Design --- Circuit Diagram
This is TI's reference design, with a simple circuit and excellent performance....
dontium Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1600  1828  289  1945  2002  33  37  6  40  41 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号