For latest revision and Regional Customer Service,
visit our website at
www.te.com
1
of 4
LOC B
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
114-1049
2.3. Drawings
Customer Drawings for product part numbers are available from the service network. If there is a conflict
between the information contained in the Customer Drawings and this specification or with any other technical
documentation supplied, the information contained in the Customer Drawings takes priority.
2.4. Specifications
Product Specification 108-1066 provides product performance and test information.
2.5. Instructional Material
Instruction Sheets (408-series) provide product assembly instructions or tooling setup and operation procedures
and Customer Manuals (409-series) provide machine setup and operating procedures. There are no documents
available that pertain to this product.
2.6. Manuals
Manual 402-40 can be used as a guide to soldering. This manual provides information on various flux types and
characteristics with the commercial designation and flux removal procedures. A checklist is included in the
manual as a guide for information on soldering problems.
3. REQUIREMENTS
3.1. Storage
A. Ultraviolet Light
Prolonged exposure to ultraviolet light may deteriorate the chemical composition used in the socket material.
B. Shelf Life
The sockets should remain in the shipping containers until ready for use to prevent deformation to the
contacts. The sockets should be used on a first in, first out basis to avoid storage contamination that could
adversely affect performance.
3.2. PC Board
A. Thickness
The recommended maximum pc board thickness is 2.36 [.093].
B. Layout
The pc board layout must be designed using the dimensions given in Figure 2.
3.3. Soldering
A. Process
Manual 402-40 provides guidelines for soldering process.
B. Flux Selection
Contact solder tines must be fluxed prior to soldering with a mildly active, rosin base flux. Selection of the
flux will depend on the type of pc board and other components mounted on the board. Additionally, the flux
must be compatible with the wave solder line, manufacturing, health, and safety requirements.
C. Cleaning
After soldering, removal of fluxes, residues, and activators is necessary. Consult with the supplier of the
solder and flux for recommended cleaning solvents.
D. Drying
When drying cleaned assemblies and pc boards, the temperature limitation must not be exceeded: 105°C
[221°F] and 85°C [185°F] for copper alloy contact material. Excessive temperatures may cause housing
degradation and/or plating deterioration.
Rev
A
2
of 4
114-1049
A
25.4 [.100] Typ
0.914±0.076[.036±.003]
Dia Typ
0.228 [.009] M
B±0.102 [.004]
A (Ref)
B±0.102 [.004]
SOCKET NUMBER OF POSITIONS
6-20
22
24-48
64
CENTERLINE SPACING DIMENSION
A
076.2
[.300]
10.16 [.400]
15.24 [.600]
22.85 [.900]
Figure 2
B
3.81 [.150]
5.08 [.200]
7.62 [.300]
—
3.4. Seating the Socket
To hold the socket in place during handling and soldering, solder tail clinching may be desired. Method of
clinching is at the discretion of the application.
NOTE
Sockets with a retention leg do not need clinching to hold them in place.
i
Excessive force to the ends of the solder tails (perpendicular to the pc board) must be avoided; otherwise the
contacts could become dislodged from their position in the housing.
3.5. Checking Installed Socket
The socket must be parallel to the pc board and the housing must be bottomed on the pc board. Solder fillets
must be evenly formed around each contact solder tine. There must be no cracks in the solder.
4. QUALIFICATION
DIPLOMATE DL low-profile DIP sockets are Recognized by Underwriters Laboratories Inc. (UL) and Certified by
CSA International.
5. TOOLING
These sockets can be applied to the pc board manually or by automatic machine. For recommended machines,
call TOOLING ASSISTANCE CENTER at the number at the bottom of page 1.
Rev
A
3
of 4
114-1049
6. VISUAL AID
The illustration below shows a typical application of this product. This illustration should be used by production
personnel to ensure a correctly applied product. Applications which DO NOT appear correct should be inspected
using the information in the preceding pages of this specification and in the instructional material shipped with
There are 3 devices on the I2C line, 2 of them work normally, and one of them responds to the ACK signal when I send a read or write command to it, but the read and write cannot get the correct value....
[i=s]This post was last edited by ddllxxrr on 2020-12-15 19:38[/i]Binary semaphore is the synchronization between tasks and interrupts. Simply put, it is the value of 0 and 1.First, use STM32CUBEMX to...
As mentioned, I have been working on this board for a long time but I still can’t use it. Every time I press Download and Debug, it says Fatal error: ST-Link Connection error Session aborted! Can anyo...
To differentiate their products in a crowded and competitive market, manufacturers of handheld devices often consider battery life and power management as key selling points for cell phones, PDAs, ...[Details]
July 11, 2012, Beijing - Altera Corporation (NASDAQ: ALTR) today announced the launch of 40-Gbps Ethernet (40GbE) and 100-Gbps Ethernet (100GbE) intellectual property (IP) core products. These core...[Details]
In the previous series, we have listed some basic knowledge of C language in Tables 1 to 3. We hope that beginners can strengthen their memory of the above tables and gradually learn to use them wh...[Details]
Instrument stepper motor
The stepper motor is an open-loop control element that converts electrical pulse signals into angular displacement or linear displacement. In the case of non...[Details]
A standard cell
is an electrochemical
cell
used as a voltage reference standard in many electrical standards laboratories
. If properly maintained, standard cells are very stable. The ...[Details]
I. Introduction
Since RS232 has a short communication distance (only 15 meters according to EAT/TAI-232 standard), and can only perform point-to-point communication, it cannot directly f...[Details]
Digital array radar (DAR) uses digital beam forming (DBF) in both receiving and transmitting modes to achieve flexible distribution and reception of RF signal power in the airspace, obtain excellent t...[Details]
In the single-chip microcomputer system, in addition to display devices, sound devices are often used, and the most common sound device is the buzzer. Buzzers are generally used for some low-demand...[Details]
Experimental tasks
A DS18B20 is used to form a temperature measurement system. The temperature measurement accuracy reaches 0.1 degrees. The temperature range is between -20 degrees and +50 de...[Details]
TC9012F is a universal CMOS large-scale integrated circuit for infrared remote control signal transmission, suitable for remote control of TV, VTR, laser player and other equipment. In the market, ...[Details]
In 2012, more than half of the cars in the European, Japanese and American car markets will be equipped with color displays, navigation systems, satellite communications and other in-vehicle infota...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guangzho...[Details]
introduction
At present, measuring instruments are developing towards networking, and each individual embedded instrument will become a node on the Internet. This system realizes the network...[Details]
1 Introduction to LED
With the development of science and technology, people have higher and higher requirements on automobile light sources. LED (Light Emitting Diode) has gradually attracted...[Details]
1 Development of LED Film and Television Lighting
1.1 The significance of developing film and television lighting
Lighting power consumption accounts for a large proportion of the total p...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
