LDECC1820KA5N00 datasheet, PDF

Datasheet> All Categories > Passive components> capacitor> LDECC1820KA5N00

LDECC1820KA5N00: DescriptionFilm Capacitor, Polyethylene Naphthalate, 50V, 0.0082uF, 1913; CategoryPassive components capacitor; File Size2MB，19 Pages; ManufacturerKEMET; Websitehttp://www.kemet.com; Environmental Compliance

Download Datasheet Parametric View All

LDECC1820KA5N00 Overview

Film Capacitor, Polyethylene Naphthalate, 50V, 0.0082uF, 1913

LDECC1820KA5N00 Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	KEMET
Reach Compliance Code	compliant
ECCN code	EAR99
capacitance	0.0082 µF
Capacitor type	FILM CAPACITOR
dielectric materials	POLYETHYLENE NAPHTHALATE
high	1.8 mm
length	4.7 mm
negative tolerance	10%
Number of terminals	2
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package form	SMT
method of packing	TR, 13 Inch
positive tolerance	10%
Rated (AC) voltage (URac)	40 V
Rated (DC) voltage (URdc)	50 V
Guideline	AEC-Q200
size code	1913
width	3.3 mm

Preview

Download Datasheet

View All

General Purpose, High Stability and AC Line EMI Suppression

LDE Series Unencapsulated Stacked Chip,

Size 1206 – 6054, 50 – 1,000 VDC

Overview

Polyethylene naphthalate (PEN) film capacitor for surface

mounting.

Applications

Typical applications include bypassing and signal coupling. LDE

is a general purpose series designed for the highest reliability

and high temperature service.

Benefits

•

Rated voltage: 50 – 1,000 VDC

Rated voltage: 40 – 250 VAC

Capacitance range: 0.001 – 4.7 µF

EIA size: 1206 – 6054

Capacitance tolerance: ±10%, ±20%, ±5% on request

Climatic category: 55/125/56

RoHS Compliant and lead-free terminations

Operating temperature range of -55˚C to +125˚C

Part Number System

LDE

Series

Metallized

PEN

Rated Voltage

(VDC)

C = 50

D = 63

E = 100

I = 250

M = 400

P = 630

Q = 1000

Size Code

See

Dimension

Table

2560

Capacitance Code (pF)

Digits 2 – 4 indicate the

first three digits of the

capacitance value.

First digit indicates the

number of zeros to be

added.

Capacitance

Tolerance

K = ±10%

M = ±20%

J = ±5% on

request

Version

A5 = Standard

A0 = Miniature

Packaging Code

See Ordering

Options Table

Internal Use

00 (Standard)

One world. One KEMET

F3078_LDE • 4/4/2013

Recommended Resources

DIY a simple FM wireless microphone

Double-arm thyristor module AC voltage regulating circuit

Haofeng NDS-20A oil-filled electric heater circuit diagram

Motorcycle battery charger circuit diagram

EKG FM Demodulator Circuit

Fully built-in caller ID chip circuit

WINCE4.2 installation error, please help!: An error occurred during the installation of WINCE4.2. The error message is as follows: Error 21337. Setup encountered problems installing some critical emulation components. You may continue the inst...; 小飞龙 Embedded System

Verilog failed to write frequency counter FPGA (cyclone4) development board experience 05: It is not right to not learn HDL language after getting an FPGA board. I looked at the Verilog tutorial and felt that it was too empty to just read it. I might as well do something. So I decided to ma...; astwyg FPGA/CPLD

stm32 learning (3)--GPIO: The IO ports of STM32 can be configured into 8 modes by software: 1. Input floating 2. Input pull-up 3. Input pull-down 4. Analog input 5. Open-drain output 6. Push-pull output 7. Push-pull multiplexi...; tzzhuang stm32/stm8

SDRAM controller: I want to know how to implement the arbitration code in the command of the sdram controller code segment? The code segment is as follows: // set command_delay shift register and command_done flag // T...; 小霍 FPGA/CPLD

If the GPMC of AM335X is connected to the FPGA, does it need a separate clock to provide to the FPGA?: As the title says! If you have done this, please give me some advice. When I was working on AM335X, I found that the GPMC_CLK pin of its GPMC bus interface only outputs a clock when the interface is o...; slugger_tp DSP and ARM Processors

I want to develop into a computer architecture engineer, what should I pay attention to?: I have been working as a C++ engineer for several years and have always been interested in low-level development and hardware. I would like to develop in the direction of architecture and plan to do m...; henluo Embedded System

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components