EEWORLDEEWORLDEEWORLD

Part Number

Search

2-147110-1

Description
HEADER CONNECTOR,PCB MNT,PLUG,42 CONTACTS,SKT,0.1 PITCH,SURFACE MOUNT TERMINAL,BLACK
CategoryThe connector    The connector   
File Size515KB,13 Pages
ManufacturerTE Connectivity
Websitehttp://www.te.com
Download Datasheet Parametric View All

2-147110-1 Overview

HEADER CONNECTOR,PCB MNT,PLUG,42 CONTACTS,SKT,0.1 PITCH,SURFACE MOUNT TERMINAL,BLACK

2-147110-1 Parametric

Parameter NameAttribute value
MakerTE Connectivity
Reach Compliance Codeunknown
Other featuresTAPE AND REEL PACKAGING
body width0.22 inch
subject depth0.26 inch
body length2.1 inch
Body/casing typePLUG
Connector typeBOARD CONNECTOR
Contact to complete cooperationSN-PB ON NI
Contact completed and terminatedTIN/LEAD OVER NICKEL
Contact point genderFEMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact resistance12 mΩ
Contact styleSQ PIN-SKT
Dielectric withstand voltage750VAC V
Durability75 Cycles
maximum insertion force2.502 N
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialPOLYPHENYLENE SULPHIDE
Manufacturer's serial number147110
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation methodSTRAIGHT BOTTOM MOUNT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing6.35 mm
Plating thickness100u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal pitch2.54 mm
Termination typeSURFACE MOUNT
Total number of contacts42
Evacuation force-minimum value.417 N
AMPMODU*
Mod II and Mod IV Printed
Circuit Board Connectors
Application Specification
114-25018
19 MAY 08
Rev E
NOTE
i
All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters. Unless
otherwise specified, dimensions have a tolerance of +0.13 and angles have a tolerance of +2 . Figures and
illustrations are for identification only and are not drawn to scale.
_
1. INTRODUCTION
This specification covers the requirements for application of AMPMODU Mod II and Mod IV Printed Circuit
(PC) Board Connectors for through hole and Surface Mount Technology (SMT). The connectors are available
with double beam receptacle contacts designed to accept 0.64 mm square posts. There are connectors in 2
through 80 positions for top and bottom entry applications as well as pass through applications with 2.54 mm
contact centerline spacing. All side entry connectors are available in 4 through 130 positions for double rows
and 2 through 65 positions for single row. The double beam contact connectors are available with single and
double rows of contacts. There are various solder lead configurations to meet a variety of system
requirements.
There are surface mount connectors available with and without hold–downs. The hold–downs help position the
connector on the pc board and hold it in place during soldering. Through hole connectors are available with and
without retentive contact leads. The retentive contact leads help stabilize and hold the connector in place
during soldering. Connectors without hold–down or retentive contact lead stabilizing features are available to
accommodate alternate system requirements.
When corresponding with Tyco Electronics Personnel, use the terminology provided on this specification to
help facilitate your inquiry for information. Basic terms and features of components are provided in Figure 1.
Double Beam Contact
Connectors (Typ)
Double Row
Connector
Single Row
Dual Entry
Connector
Mating
Face
Double Row
Connector
Dual
Entry
Right-Angle
Horizontal
Top Entry
Contact
Cavity
Connector
Dual Entry
Right-Angle Surface
Mount (Horizontal)
Single Row
Connector
Figure 1
E
2008 Tyco Electronics Corporation, Harrisburg, PA
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at
www.tycoelectronics.com
1
of 13
LOC B
All International Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other products, logos, and company names used are the property of their respective owners.
Earn points and settle immediately...
...
weijinping Embedded System
The widespread application of RFID will effectively improve the level of urban management
[Abstract] If RFID is to be used in urban management, there are still many problems, such as security and privacy issues. For example, the RFID chip used in the manhole cover has problems such as data...
tmily RF/Wirelessly
618 What did you buy?
I'd just like to ask what cost-effective things everyone bought during the 618 shopping event. Feel free to leave a comment and share your experiences!...
eric_wang Talking
ATMEL SAM3U Chinese Manual (Chapter 1 to 18, updated continuously)
Atmel Corporation has announced the industry’s first ARM Cortex-M3 SAM3U microcontroller that integrates a high-speed (480 Mbps) USB device-and-transceiver, 4-bit 192 Mbps SDIO/SDCard 2.0, 8-bit 384 M...
小野狼 Embedded System
The Principle and Application of AC Frequency Conversion Speed Regulation
There are many ways to regulate the speed of AC asynchronous motors, such as voltage regulation, variable speed regulation, cascade speed regulation, slip speed regulation, etc., and variable frequenc...
zbz0529 Power technology
Does anyone know about Protel or OrCAD software group?
If you know, please send me the group number, thank you!...
zhaowen0201 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2775  1005  1121  449  2739  56  21  23  10  5 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号