EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-GLAFA4241

Description
Transponder, 10000Mbps(Tx), 10000Mbps(Rx), FC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-GLAFA4241 Overview

Transponder, 10000Mbps(Tx), 10000Mbps(Rx), FC/UPC Connector,

PH1-GLAFA4241 Parametric

Parameter NameAttribute value
MakerLumentum Operations LLC
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Connection TypeFC/UPC CONNECTOR
Data rate (receive)10000 Mbps
Data rate (send)10000 Mbps
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1561 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Super Awesome DIY Iron Man MK3 Ark Reactor
From "Iron Man 1" to "The Avengers" to "Iron Man 3", the reactor on Tony's chest has been updated for several generations. When I just graduated from high school and was on vacation at home, I had the...
国土安全局 Creative Market
Oscilloscope sampling rate and oscilloscope memory depth
[i=s]This post was last edited by tusho on 2017-4-6 09:44[/i] Oscilloscope sampling rate and oscilloscope memory depth Oscilloscope sampling rate and memory depth When selecting an oscilloscope, engin...
tusho Analog electronics
Directly read and write memory under wince5.0
I want to read and write memory directly under wince5.0, and read and write data to the specified space. How can I achieve this? Can anyone give me some suggestions? ! Thank you! !...
zy7786879 Embedded System
Analyzing a program error!
module delay_line(start,stop,up_out,upQ,down_out,downQ,clk,reset);input clk,start,stop,reset;reg [60:0]up_out,down_out,upQ,downQ;integer i,j,m,n;delay_unit du0(start,reset,up_out[0]);delay_unit du2(st...
eeleader FPGA/CPLD
IAP issues with LPC1788
These days, when I was carrying out SD IAP program, some of the following programs without interruption and serial port interruption could not be debugged for a long time. What's the situation? Main p...
yet NXP MCU
Why does the green color of Altium Designer's online rule check error have a pattern? Can it be changed back to the previous pure green?
[i=s] This post was last edited by 天涯海角sr on 2018-9-3 22:22 [/i]The left one is the current one. Why is there a small green pattern when zooming in on someone else's project? How can I remove it (turn...
天涯海角sr PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2590  1941  1532  233  144  53  40  31  5  3 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号