EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-GLAFC3441

Description
Transponder, 10000Mbps(Tx), 10000Mbps(Rx), FC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-GLAFC3441 Overview

Transponder, 10000Mbps(Tx), 10000Mbps(Rx), FC/UPC Connector,

PH1-GLAFC3441 Parametric

Parameter NameAttribute value
MakerJDS Uniphase Corporation ( VIAVI )
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Connection TypeFC/UPC CONNECTOR
Data rate (receive)10000 Mbps
Data rate (send)10000 Mbps
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1545 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Is there anyone who has made a launchpad touch button? Can you help me see if this design is feasible?
I want to make a launchpad expansion board, and yesterday I suddenly came up with a touchpad design like this: I wonder if it is feasibleIn fact, the principle is the same as that of a 4*4 matrix keyb...
anqi90 Microcontroller MCU
Program compatibility issues with XP systems
Program compatibility issues on XP systems. This is a network game client, compiled with VC++2003. It was working fine before, but after an update, it started to have problems: it was working fine on ...
hjklhu Embedded System
Discussion on some issues regarding advertising posts for newly registered users
Let's take action!!! After the novice registers: 1. Set up a section similar to the "water version" specifically for advertising users to flood the forum (formulate corresponding rules, and those who ...
DIAG Suggestions & Announcements
PowerBox
Complete introduction of 12V power supply with voltage meter, terminal and emergency stop button :https://www.hackster.io/DerPandaHammer/power-in-a-box-f16849...
dcexpert DIY/Open Source Hardware
Timer 0 of DSP TMS320VC5402 controls the on and off of the LED
[color=#444444][font=Tahoma,]The cputimer program provided by the board has a problem. I hope you can help me with it. When the DSP is single-step debugged, the value of the register CLKMD does not ch...
梦知秋 DSP and ARM Processors
I want an expert to look at a problem with UART sending and receiving automatically!
The chip is MSP430F5310 and the environment is IAR5.20.1. The code is implemented as follows: void Init_Clk(void) {P5SEL |= BIT4+BIT5; // Enable XT1 function pinUCSCTL6 &= ~(XT1OFF); // XT1 turn onUCS...
wuyanyanke Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2592  1126  2042  2647  2027  53  23  42  54  41 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号