The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
High-Speed (3.125Gbps) Stacking Connectors
FX8C Series
sMechanical
features
q
0.6mm Pitch
q
Stacking Height : 5~16mm
q
Number of Contacts : 60, 80, 100, 120, 140,
q
SMT Coplanarity
q
Mating Guide
160, 200, 240, 280
The coplanarity of the SMT solder area lead is
maintained at the high accuracy of less than 0.1mm.
The very small and guide rib is provided, and secures
±0.6mm self-alignment, considering the mating
operativity into accounts. ( fig.1 )
2
Effective Mating Length
fig.1
H
+0.3
-0.2
q
Effective Mating Length : 2mm ( fig.1 )
q
Mis-insertion Prevention
q
Two-piece Connection Product
The boss prevents mis-insertion in the board to cause
due to the boss position and boss diameter.
In order to enhance the mating reliability for fine pitch
connector using two-pieces, the two-pieces of
connectors are combined by our unique method, and
can secure the mount position accuracy. In such a
new concept, the two-piece connected product is
prepared at every number of contacts ( The standard
mating pitch for the two-piece interconnected product
in two rows is 11mm. )
H:Stacking Height
0.6
0.6
s
Signal integrity features
q
Insertion-Loss-to-Crosstalk-Ratio ( ICR )
The insertion-loss-to-crosstalk ratio (ICR) with
five-aggressor differential FEXT meets the IEEE
802.3ap specification for 3.125
+
Gbps with plenty
of margins.
The differential impedance is within 100±10 ohms
at 100 ps rise time (20% to 80%).
q
Differential Impedance
s
Stacking height variations (5mm~16mm)
Receptacle
Header
FX8C-**P-SV
FX8C-** / **P11-SVJ
FX8C-**P-SV1
FX8C-** / **P11-SV1J
FX8C-**P-SV2
FX8C-**/**P11-SV2J
FX8C-**P-SV4
FX8C-** / **P11-SV4J
FX8C-**P-SV6
FX8C-** / **P11-SV6J
FX8C-**S-SV
FX8C-** / **S11-SVJ
5mm
6mm
7mm
9mm
11mm
FX8C-**S-SV5
FX8C-** / **S11-SV5J
10mm
5∼16
11mm
12mm
14mm
16mm
9
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions.
5.
Humidity (Steady state)
Contact resistance: 100m
ohms
max.Insulation resistance: 100M
ohms
min.
96 hours at temperature of 40 ± 2ç and humidity of 90% to 95%
Contact resistance: 100m
ohms
max.Insulation resistance: 100M
ohms
min. (-55ç: 30 minutes, 15
to
35ç: 2
to
3 minutes
(-85ç:
30 minutes, 15
to
35ç: 2
to
3minutes) 5 cycles
7. Durability (Mating/un-mating) Contact resistance: 100m
ohms
max.
50 cycles
8. Resistance to Soldering heat
No deformation of components affecting performance. Reflow: At the recommended temperature profile
Manual soldering: 360ç for 5 seconds
Note 1 : Includes temperature rise caused by current flow.
Note 2 : The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and
Humidity range covers non conducting condition of installed connectors in storage, shipment or during transportation.
Note 3 : Slight variations in color of the plastic compounds do not affect form ,fit or function of the connector.
Note 4 : FX8C-*P-SV(*),FX8C-*S-SV(*) is gold plated.
Note 5 : Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and specifications for a
specific part number shown.
sMaterial
Part
Insulator
Header Contact
Receptacle Contact
Material
PPS
Phosphor bronze
Phosphor bronze
Finish
Light brown
Contact area
Lead area
Contact area
Lead area
Gold plated
Tin plated(Note 4)
Gold plated
Tin plated(Note 4)
Remarks
UL94V-0
–––––––
–––––––
sOrdering
Information
qSingle
Product
FX8C
q
- 120 P - SV 1 (91)
w
e
r
t
y
t
Product height variation Blank : Standard (Minimum low profile)
1:
+1mm
. . . . . . 6:+6mm
y
Packaging Type
(71) : Tray packaging
(91) : Tube packaging
(92) : Embossed tape package
q
Series Name : FX8C
w
Number of Contacts :60, 80, 100, 120, 140
e
Connector type
r
Contact type
P :Header
S :Receptacle
SV :Board vertical type
qtwo-piece
Connection Product
FX8C
q
- 120/120 P 11 - SV 1 J
w
e
r
t
y u
r
Connector to Connector Pitch
t
Contact type
SV : Board vertical type
y
Product Height VariationBlank : Standard (Minimum lot profile)
1:+1mm . . . . . . 6:+6mm
u
J: two-piece connection product
q
Series Name :FX8C
w
Number of Contacts: 60∞2, 80∞2, 100∞2,
120∞2, 140∞2
Example: 120/120 = 240 contacts
e
Connector Type :
P : Header
S : Receptacle
*The
standard packaging of the two-piece connection product is the tray packaging.
10
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
To match 100 ohm differential impedance and to reduce crosstalk, a staggered GSGSG pin assignment is recommended for
FX8C of 5mm to 9mm height, and a staggered GSSG pin assignment is recommended for 10mm to 16mm height. (G=ground
and S=signal)
GSGSG
GSSG
signal
ground
q
Impedance
The differential impedance is 100 ± 10 ohm for FX8C of 5mm and 16mm height at 100 ps rise time (20% to 80%).
5mm
16mm
q
Propagation delay
The propagation delay is 69 and 118 ps for FX8C of 5mm and 16mm height, respectively.
q
Insertion loss
The differential insertion loss crosses 1 dB at 7 and 5 GHz for FX8C of 5mm and 16mm height, respectively.
5mm
16mm
11
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
The differential return loss meets the IEEE 802.3ap specification to 10 and 7 GHz for FX8C of 5mm and 16mm height,
respectively.
5mm
16mm
q
Near-end crosstalk (NEXT)
The staggered GSGSG and GSSG pin assignments resulted in low differential NEXT.
5mm
16mm
12
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
[i=s]This post was last edited by Chocho on 2017-3-13 09:43[/i] [b]micropython udp on esp8266[/b][align=left]TCP is to establish a reliable connection, and both communicating parties can send data in ...
[p=28, 2, left][color=rgb(51, 51, 51)][font=宋体]TL494 is a voltage-driven pulse width modulation control integrated circuit, which is widely used in various switching power supplies. You may not be fam...
1. Introduction In recent decades, power electronics technology has been continuously developed and widely used in various fields such as industry, civil and military. The large-scale application of p...
From: https://www.instructables.com/id/The-Sixth-Finger/A sixth finger made with a flex sensor, Circuit Playground Express, and programmable with CircuitPython...
High efficiency and low standby power consumption are two major challenges in today's switching power supply design. Resonant topology or LLC topology is becoming increasingly popular because it ca...[Details]
introduction
With the continuous optimization of surface mount technology (SMT) and the rapid development of chip component manufacturing technology, the application of chip mounters in the el...[Details]
introduction
my country has a vast territory and a large population. The scale of housing construction is huge, and the amount of residential construction is large and wide. It is still on t...[Details]
1. Introduction
Automobile pollution is one of the most important issues that people are most concerned about and need to solve urgently. As an important method for detecting automobile exhau...[Details]
0 Introduction
With the development of my country's economy, the number of motor vehicles continues to increase. The growth of existing roads and other hardware facilities can no longer meet t...[Details]
introduction
In the discharge process of tokamak plasma physics, the study of rupture and sawtooth is of great significance. Rupture and sawtooth exist in most tokamaks. Rupture is a notew...[Details]
All electronic design engineers and scientists have performed electrical signal analysis, or signal analysis for short. Through this basic measurement, they can gain insight into signal details and...[Details]
In this article, the high-performance DSP developed by TI can be used as an effective confidentiality method if it is applied to PC encryption cards.
As an effective network security solution,...[Details]
1 Introduction
With the acceleration of the pace of urban modernization, society has higher requirements for urban road lighting and urban lighting projects. The state has clearly required tha...[Details]
With the development and widespread application of computer technology, especially in the field of industrial control, computer communication is particularly important. Although serial communication g...[Details]
1. Introduction
At present, most lighting equipment still uses traditional energy for lighting. Making full use of solar energy as the energy supply for lighting equipment is of great si...[Details]
Contact resistance
is the resistance to current flow through a closed pair of contacts. This type of measurement is performed on devices such as connectors,
relays
, and switches. The...[Details]
Overview:
This paper introduces a method of connecting a CAN-bus network with Ethernet to form a medium-sized remote monitoring/data transmission network.
CAN (Controller Area Network) is ...[Details]
1 Introduction
PROFIBUS is an international, open, and manufacturer-independent fieldbus standard. It is widely used in manufacturing automation, process industry automation, and automatio...[Details]
1 Introduction to HART Protocol
HART (Highway Addressable Remote Transducer), an open communication protocol for addressable remote sensor high-speed channels, was launched by Rosemen in the U...[Details]
_pdf/pg_0001.png)
MicroPython Open Source section
京公网安备 11010802033920号
EEWORLD_pdf/1.png)
_pdf/2.png)
_pdf/3.png)
_pdf/4.png)
_pdf/5.png)
_pdf/pg_0002.png)
_pdf/pg_0003.png)
_pdf/pg_0004.png)
_pdf/pg_0005.png)
