EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-SLPFA3881

Description
Transponder, FC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-SLPFA3881 Overview

Transponder, FC/UPC Connector,

PH1-SLPFA3881 Parametric

Parameter NameAttribute value
MakerJDS Uniphase Corporation ( VIAVI )
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Communication standardsOC-192, SONET
Connection TypeFC/UPC CONNECTOR
Emitter/Detector TypePIN PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1554 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-17 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
【EEworld original tutorial discussion】A tutorial that is spot-on
[size=5]{:1_102:}Our EE tutorial is really good. The explanation is very precise and the experience and practice are explained very clearly. I just watched the course "Using LaunchPad IDE Development ...
mengyun2801 Microcontroller MCU
SPI Communication
What mechanisms can be added to ensure the integrity of files when transferring files via the SPI bus? Is timeout retransmission possible?...
asdbhk stm32/stm8
Clamping circuit
What is the function of the 500Ω R5 in the figure? Why does the teacher say that the clamping effect will be very poor without this resistor? Due to the impedance requirements of the subsequent circui...
盛世龙精灵 Analog electronics
How to Correctly Select and Configure Camera Power Supply
Keyword: [b] Camera power supply [/b] Although the camera is marked with DC12V/AC24V [url=http://www.yucoo.com/peijian/][color=#000000] Camera power supply [/color][/url], it is better to choose AC24V...
yucooxfj Industrial Control Electronics
GPS vehicle terminal EMC test problem
I wonder if anyone has made a car GPS terminal. If you use GPRS to do EMC, how should the terminal operate the GSM module? Currently, it is not possible to attach to the GPRS network. I wonder if anyo...
mini2440 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1952  1276  450  2591  2180  40  26  10  53  44 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号