EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-TLPSC2842

Description
Transponder, 10660Mbps(Tx), 10660Mbps(Rx), SC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-TLPSC2842 Overview

Transponder, 10660Mbps(Tx), 10660Mbps(Rx), SC/UPC Connector,

PH1-TLPSC2842 Parametric

Parameter NameAttribute value
MakerLumentum Operations LLC
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Connection TypeSC/UPC CONNECTOR
Data rate (receive)10660 Mbps
Data rate (send)10660 Mbps
Emitter/Detector TypePIN PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1533 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-17 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Title: How to force the pin state of TI DSP's ePWM?
When using EV in 2812, you can directly write EVx.ACTRx to directly control the forced high and forced low of PWM output. How should I configure it on the device using ePWM so that it can be forced hi...
paradoxfx Microcontroller MCU
Seeking RF wake-up solution
Looking for RF wake-up solution, 125KHz low frequency or high frequency is fine, as long as it can wake up. Wake-up distance <1.2m; antenna area is about 1.2mX1.2m; if you have a solution, please cont...
Andrewyancn RF/Wirelessly
System clock
MCLK represents the CPU operation and system clock. 430 executes a simple instruction in one clock cycle. Why does it take the same time to execute the same code when MCLK=REFOCLK (32768HZ) and MCLK=X...
jacken.bool Microcontroller MCU
Question about calculating high level time of input capture
[i=s] This post was last edited by electrics on 2016-9-26 00:33 [/i] while(1) { if(((TIM2->SR&0X0001)==1)&&((TIM2->CCER & 0X0002)==0X0002)) //Falling edge trigger and judgment is reaching the maximum ...
electrics stm32/stm8
Interface Technology Simulation Test
Single-choice questions 1. The transmission mode in which the microprocessor only starts the peripherals without intervening in the transmission process is _________ mode. A. Interrupt B. DMA C. Query...
a79571843 Embedded System
Application of Single Bus Protocol Converter in Distributed Measurement and Control System
Abstract: This paper introduces the main features, working principle and interface technology of DS2480B UART/RS232 to single bus protocol converter, and specifically explains the application of DS248...
rain MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 738  2668  1882  2181  1976  15  54  38  44  40 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号