The “Absolute Maximum Ratings” are those values beyond which the safety
of the device cannot be guaranteed. The device should not be operated at these lim-
its. The parametric values defined in the Electrical Characteristics tables are not
guaranteed at the absolute maximum ratings. The “Recommended Operating Condi-
tions” table will define the conditions for actual device operation.
Note 2:
The input and output negative voltage ratings may be exceeded if the input
and output diode current ratings are observed.
Note 3:
Unused inputs must be held HIGH or LOW. They may not float.
DC Electrical Characteristics
V
CC
Symbol
V
IH
V
IL
I
IN
I
OFF
R
ON
Parameter
HIGH Level
Input Voltage
LOW Level
Input Voltage
Control Input
Leakage Current
OFF Leakage Current
Switch On Resistance
(Note 4)
4.5
(V)
1.65 to 1.95
2.3 to 5.5
1.65 to 1.95
2.3 to 5.5
0 to 5.5
1.65 to 5.5
±0.05
±0.05
3.0
5.0
7.0
3.0
2.3
1.8
R
flat
On Resistance Flatness
(Note 4)(Note 6)(Note 7)
5.0
3.3
2.5
1.8
I
CC
Quiescent Supply Current
1.65 to 5.5
0.05
10.0
4.0
10.0
5.0
13.0
7.0
25.0
Min
0.75 V
CC
0.7 V
CC
0.25 V
CC
0.3 V
CC
±1.0
±10.0
7.0
12.0
15.0
9.0
20.0
12.0
30.0
28.0
60.0
6.0
12.0
28.0
125
μA
Ω
Ω
T
A
= −40°C
to
+85°C
Typ
(Note 5)
Max
Min
T
A
= +25°C
Typ
Max
Units
Conditions
V
V
μA
μA
0
≤
V
IN
≤
5.5V
0
≤
A, B
≤
V
CC
V
IN
=
0V, I
IN
=
30 mA
V
IN
=
2.4V, I
IN
=
15 mA
V
IN
=
4.5V, I
IN
=
30 mA
V
IN
=
0V, I
IN
=
24 mA
V
IN
=
3V, I
IN
=
24 mA
V
IN
=
0V, I
IN
=
8 mA
V
IN
=
2.3V, I
IN
=
8 mA
V
IN
=
0V, I
IN
=
4 mA
V
IN
=
1.8V, I
IN
=
4 mA
I
A
= −30
mA, 0
≤
V
Bn
≤
V
CC
I
A
= −24
mA, 0
≤
V
Bn
≤
V
CC
I
A
= −8
mA, 0
≤
V
Bn
≤
V
CC
I
A
= −4
mA, 0
≤
V
Bn
≤
V
CC
V
IN
=
V
CC
or GND
I
OUT
=
0
Note 4:
Measured by the voltage drop between A and B pins at the indicated current through the switch. On Resistance is determined by the lower of the
voltages on the two (A or B) pins.
Note 5:
All typical values are at the specified V
CC
, and T
A
=
25°C.
Note 6:
Parameter is characterized but not tested in production.
Note 7:
Flatness is defined as the difference between the maximum and minimum value of On Resistance over the specified range of conditions.
3
www.fairchildsemi.com
AC Electrical Characteristics
T
A
= −40°C
to
+85°C,
Symbol
Parameter
V
CC
(V)
t
PHL
, t
PLH
Propagation Delay Bus to Bus
(Note 9)
1.65 to 1.95
2.3-2.7
3.0-3.6
4.5-5.5
t
PZL
, t
PZH
Output Enable Time
1.65 to 1.95
2.3-2.7
3.0-3.6
4.5-5.5
t
PLZ
, t
PHZ
Output Disable Time
1.65 to 1.95
2.3-2.7
3.0-3.6
4.5-5.5
Note 8:
All typical values are at the specified V
CC
, and T
A
=
25°C.
Note 9:
This parameter is guaranteed by design but is not tested. The switch contributes no propagation delay other than the RC delay of the typical On Resistance of the switch
and the 50 pF load capacitance, when driven by an ideal voltage source (zero output impedance).
京公网安备 11010802033920号
EEWORLD
