EEWORLDEEWORLDEEWORLD

Part Number

Search

E2SBA18-8.000M

Description
QUARTZ CRYSTAL RESONATOR, 8MHz, ROHS COMPLIANT, RESISTANCE WELDED, SMD, 2 PIN
CategoryPassive components    Crystal/resonator   
File Size139KB,4 Pages
ManufacturerECLIPTEK
Websitehttp://www.ecliptek.com
Environmental Compliance  
Download Datasheet Parametric Compare View All

E2SBA18-8.000M Overview

QUARTZ CRYSTAL RESONATOR, 8MHz, ROHS COMPLIANT, RESISTANCE WELDED, SMD, 2 PIN

E2SBA18-8.000M Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerECLIPTEK
package instructionROHS COMPLIANT, RESISTANCE WELDED, SMD, 2 PIN
Reach Compliance Codecompliant
Other featuresAT-CUT CRYSTAL; BULK
Ageing5 PPM/YEAR
Crystal/Resonator TypePARALLEL - FUNDAMENTAL
Drive level1000 µW
frequency stability0.01%
frequency tolerance50 ppm
JESD-609 codee3
load capacitance18 pF
Installation featuresSURFACE MOUNT
Nominal operating frequency8 MHz
Maximum operating temperature70 °C
Minimum operating temperature-20 °C
physical sizeL13.3XB4.85XH4.5 (mm)/L0.524XB0.191XH0.177 (inch)
Series resistance90 Ω
surface mountYES
Terminal surfaceMatte Tin (Sn) - with Nickel (Ni) barrier

E2SBA18-8.000M Preview

E2SBA18-8.000M
Series
RoHS Compliant (Pb-free) Resistance Welded
HC-49/UP SMD Crystal
Frequency Tolerance/Stability
±50ppm at 25°C, ±100ppm over -20°C to +70°C
Mode of Operation
AT-Cut Fundamental
RoHS
Pb
E2S B A 18 -8.000M
Nominal Frequency
8.000MHz
Load Capacitance
18pF Parallel Resonant
ELECTRICAL SPECIFICATIONS
Nominal Frequency
Frequency Tolerance/Stability
Aging at 25°C
Load Capacitance
Shunt Capacitance (C0)
Equivalent Series Resistance
Mode of Operation
Drive Level
Storage Temperature Range
Insulation Resistance
8.000MHz
±50ppm at 25°C, ±100ppm over -20°C to +70°C
±5ppm/year Maximum
18pF Parallel Resonant
7pF Maximum
90 Ohms Maximum
AT-Cut Fundamental
1mWatt Maximum
-40°C to +125°C
500 Megaohms Minimum at 100Vdc
ENVIRONMENTAL & MECHANICAL SPECIFICATIONS
Fine Leak Test
Gross Leak Test
Lead Termination
Mechanical Shock
Resistance to Soldering Heat
Resistance to Solvents
Solderability
Temperature Cycling
Vibration
MIL-STD-883, Method 1014 Condition A
MIL-STD-883, Method 1014 Condition C
Sn 2µm - 6µm
MIL-STD-202, Method 213 Condition C
MIL-STD-202, Method 210
MIL-STD-202, Method 215
MIL-STD-883, Method 2003
MIL-STD-883, Method 1010
MIL-STD-883, Method 2007 Condition A
MECHANICAL DIMENSIONS (all dimensions in millimeters)
LINE MARKING
1
4.50
MAX
E8.000M
E=Ecliptek Designator
M=MHz
13.30 MAX
4.85
MAX
4.88 ±0.20
0.50 MIN (x2)
0.80 ±0.30 (x2)
11.60 MAX
NOTE: Coplanarity 0.360 MAX
www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 2/16/2010 | Page 1 of 4
E2SBA18-8.000M
Suggested Solder Pad Layout
All Dimensions in Millimeters
5.5 (X2)
2.0 (X2)
4.0
Solder Land
(X2)
All Tolerances are ±0.1
www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 2/16/2010 | Page 2 of 4
E2SBA18-8.000M
Recommended Solder Reflow Methods
T
P
Critical Zone
T
L
to T
P
Ramp-up
Ramp-down
Temperature (T)
T
L
T
S
Max
T
S
Min
t
S
Preheat
t 25°C to Peak
t
L
t
P
Time (t)
High Temperature Infrared/Convection
T
S
MAX to T
L
(Ramp-up Rate)
Preheat
- Temperature Minimum (T
S
MIN)
- Temperature Typical (T
S
TYP)
- Temperature Maximum (T
S
MAX)
- Time (t
S
MIN)
Ramp-up Rate (T
L
to T
P
)
Time Maintained Above:
- Temperature (T
L
)
- Time (t
L
)
Peak Temperature (T
P
)
Target Peak Temperature (T
P
Target)
Time within 5°C of actual peak (t
p
)
Ramp-down Rate
Time 25°C to Peak Temperature (t)
Moisture Sensitivity Level
3°C/second Maximum
150°C
175°C
200°C
60 - 180 Seconds
3°C/second Maximum
217°C
60 - 150 Seconds
260°C Maximum for 10 Seconds Maximum
250°C +0/-5°C
20 - 40 seconds
6°C/second Maximum
8 minutes Maximum
Level 1
www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 2/16/2010 | Page 3 of 4
E2SBA18-8.000M
Recommended Solder Reflow Methods
T
P
Critical Zone
T
L
to T
P
Ramp-up
Ramp-down
Temperature (T)
T
L
T
S
Max
T
S
Min
t
S
Preheat
t 25°C to Peak
t
L
t
P
Time (t)
Low Temperature Infrared/Convection 245°C
T
S
MAX to T
L
(Ramp-up Rate)
Preheat
- Temperature Minimum (T
S
MIN)
- Temperature Typical (T
S
TYP)
- Temperature Maximum (T
S
MAX)
- Time (t
S
MIN)
Ramp-up Rate (T
L
to T
P
)
Time Maintained Above:
- Temperature (T
L
)
- Time (t
L
)
Peak Temperature (T
P
)
Target Peak Temperature (T
P
Target)
Time within 5°C of actual peak (t
p
)
Ramp-down Rate
Time 25°C to Peak Temperature (t)
Moisture Sensitivity Level
5°C/second Maximum
N/A
150°C
N/A
30 - 60 Seconds
5°C/second Maximum
150°C
200 Seconds Maximum
245°C Maximum
245°C Maximum 2 Times / 230°C Maximum 1 Time
10 seconds Maximum 2 Times / 80 seconds Maximum 1 Time
5°C/second Maximum
N/A
Level 1
Low Temperature Manual Soldering
185°C Maximum for 10 seconds Maximum, 2 times Maximum.
High Temperature Manual Soldering
260°C Maximum for 5 seconds Maximum, 2 times Maximum.
www.ecliptek.com | Specification Subject to Change Without Notice | Rev F 2/16/2010 | Page 4 of 4

E2SBA18-8.000M Related Products

E2SBA18-8.000M E2SBA18-8.000M TR
Description QUARTZ CRYSTAL RESONATOR, 8MHz, ROHS COMPLIANT, RESISTANCE WELDED, SMD, 2 PIN CRYSTALS 50/100 -20+70 18PF 8.000MHZ ATCUT FUND HC-49/UP
Is it lead-free? Lead free Lead free
Is it Rohs certified? conform to conform to
Reach Compliance Code compliant unknown
Monthly Original Selection June 2018 (No. 5)
[size=4][color=#ff0000] Event time[/color]: June 1st - June 30th, 2018 (5th issue)[/size] [size=4][color=#0000ff]Selection scope[/color]: DIY example posts, technical knowledge explanation posts, high...
okhxyyo Suggestions & Announcements
Share FATFS system code that supports long Chinese file names
I found it after searching on the Internet. It supports fat32 file system and Chinese long file names. When using it, just add the cc936.c file to the project. It is used in the same way as ordinary f...
shower.xu Microcontroller MCU
Can someone help me look at this circuit and explain it to me?
Can someone help me look at this circuit and explain it to me, thank you...
曹伟1993 PCB Design
Building a precision transmission test platform, please give me some advice, I will be very grateful
Test requirements: The angular displacement accuracy of the measurement is +-1". Most of the voltage angular displacement sensors I found have an output voltage of 0~10v. The measurement ranges are 36...
x.ke Test/Measurement
What are the two MOS tubes used for in the feedback circuit of the Boost circuit?
As shown in the figure, a Boost switching power supply chip from TI provides peripheral circuits and internal block diagrams. It is obvious that the inductor and Schottky diode connected to the LX pin...
lingking Power technology
I am a newbie. How can I restart the external low-frequency crystal oscillator TX1 after exiting LPM4 mode? Thank you.
[i=s]This post was last edited by aureole on 2016-1-28 12:00[/i] I am a newbie and would like to ask how to re-enable the external low-frequency crystal oscillator TX1 after exiting LPM4 mode. I am us...
aureole Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2413  457  1139  701  1495  49  10  23  15  31 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号