4Mb
SMART 3 BOOT BLOCK FLASH MEMORY
FLASH MEMORY
Features
• Seven erase blocks:
16KB/8K-word boot block (protected)
Two 8KB/4K-word parameter blocks
Four main memory blocks
• Smart 3 technology (B3):
3.3V ±0.3V V
CC
3.3V ±0.3V
V
PP
application programming
5V ±10%
V
PP
application/production programming
1
• Compatible with 0.3µm Smart 3 device
• Advanced 0.18µm CMOS floating-gate process
• Address access time: 80ns
• 100,000 ERASE cycles
• Industry-standard pinouts
• Inputs and outputs are fully TTL-compatible
• Automated write and erase algorithm
• Two-cycle WRITE/ERASE sequence
• Byte- or word-wide READ and WRITE
(MT28F400B3, 256K x 16/512K x 8)
• Byte-wide READ and WRITE only
(MT28F004B3, 512K x 8)
•
TSOP and SOP packaging options
MT28F004B3
MT28F400B3
3V ONLY, DUAL SUPPLY (SMART 3)
40-Pin TSOP Type I
48-Pin TSOP Type I
44-Pin SOP
GENERAL DESCRIPTION
The MT28F004B3 (x8) and MT28F400B3 (x16/x8)
are nonvolatile, electrically block-erasable (flash),
programmable memory devices containing 4,194,304
bits organized as 262,144 words (16 bits) or 524,288
bytes (8 bits). Writing or erasing the device is done with
either a 3.3V or 5V V
PP
voltage, while all operations are
performed with a 3.3V V
CC
. Due to process technology
advances, 5V V
PP
is optimal for application and pro-
duction programming. These devices are fabricated
with Micron’s advanced 0.18µm CMOS floating-gate
process.
The MT28F004B3 and MT28F400B3 are organized
into seven separately erasable blocks. To ensure that
critical firmware is protected from accidental erasure
or overwrite, the devices feature a hardware-protected
boot block. Writing or erasing the boot block requires
either applying a super-voltage to the RP# pin or driv-
ing WP# HIGH in addition to executing the normal
write or erase sequences. This block may be used to
store code implemented in low-level system recovery.
The remaining blocks vary in density and are written
and erased with no additional security measures.
Refer to Micron’s Web site (www.micron.com/flash)
for the latest data sheet.
Part Number Example:
Options
•
•
•
•
•
•
•
•
•
•
•
Timing
80ns access
Configurations
1 Meg x 8
512K x 16/1 Meg x 8
Boot Block Starting Word Address
Top (3FFFFh)
Bottom (00000h)
Operating Temperature Range
Extended (-40ºC to +85ºC)
Packages
MT28F004B3
Plastic 40-pin (standard) TSOP Type I
Plastic 40-pin (lead free) TSOP Type
I
MT28F400B3
Plastic 48-pin (standard) TSOP Type I
Plastic 48-pin (lead free) TSOP Type I
Plastic 44-pin (standard) SOP
Plastic 44-pin (lead free) SOP
Marking
-8
MT28F004B3
MT28F400B3
T
B
ET
VG
VP
WG
WP
SG
2
SP
2
NOTE:
1. This generation of devices does not support 12V
V
PP
production programming; however, 5V
V
PP
application production programming can be
used with no loss of performance.
2. Contact Factory for availability
MT28F400B3SG-8 T
09005aef8114a789
F45.fm - Rev. E 6/04 EN
1
©2003 Micron Technology, Inc. All rights reserved.
PRODUCTS AND SPECIFICATIONS DISCUSSED HEREIN ARE SUBJECT TO CHANGE BY MICRON WITHOUT NOTICE.
4Mb
SMART 3 BOOT BLOCK FLASH MEMORY
Figure 1: Pin Assignment (Top View)
48-Pin TSOP Type I
A15
A14
A13
A12
A11
A10
A9
A8
NC
NC
WE#
RP#
VPP
WP#
NC
NC
A17
A7
A6
A5
A4
A3
A2
A1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
A16
BYTE#
VSS
DQ15/(A-1)
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
VCC
DQ11
DQ3
DQ10
DQ2
DQ9
DQ1
DQ8
DQ0
OE#
VSS
CE#
A0
VPP
WP#
A17
A7
A6
A5
A4
A3
A2
A1
A0
CE#
VSS
OE#
DQ0
DQ8
DQ1
DQ9
DQ2
DQ10
DQ3
DQ11
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
44-Pin SOP
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
RP#
WE#
A8
A9
A10
A11
A12
A13
A14
A15
A16
BYTE#
VSS
DQ15/(A-1)
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
VCC
ORDER NUMBER AND PART MARKING
MT28F400B3WG-8 B MT28F400B3WP-8 B
MT28F400B3WG-8 T MT28F400B3WP-8 T
MT28F400B3WG-8 BET MT28F400B3WP-8 BET
MT28F400B3WG-8 TET MT28F400B3WP-8 TET
ORDER NUMBER AND PART MARKING
MT28F400B3SG-8 B
MT28F400B3SP-8 B
MT28F400B3SG-8 T
MT28F400B3SP-8 T
MT28F400B3SG-8 BET MT28F400B3SP-8 BET
MT28F400B3SG-8 TET MT28F400B3SP-8 TET
40-Pin TSOP Type I
A16
A15
A14
A13
A12
A11
A9
A8
WE#
RP#
VPP
WP#
A18
A7
A6
A5
A4
A3
A2
A1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
A17
VSS
NC
NC
A10
DQ7
DQ6
DQ5
DQ4
VCC
VCC
NC
DQ3
DQ2
DQ1
DQ0
OE#
VSS
CE#
A0
ORDER NUMBER AND PART MARKING
MT28F004B3VG-8 B
MT28F004B3VP-8 B
MT28F004B3VG-8 T
MT28F004B3VP-8 T
MT28F004B3VG-8 BET MT28F004B3VP-8 BET
MT28F004B3VG-8 TET MT28F004B3VP-8 TET
09005aef8114a789
F45.fm - Rev. E 6/04 EN
2
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc. All rights reserved.
09005aef8114a789
F45.fm - Rev. E 6/04 EN
Figure 2: Functional Block Diagram
8
Input
Buffer
BYTE#
1
I/O
Control
Logic
7
16KB Boot Block
18 (19)
9
8KB Parameter Block
8KB Parameter Block
96KB Main Block
Input
Buffer
A-1
Input Data
Latch/Mux
16
128KB Main Block
Command
Execution
Logic
State
Machine
Y-
Decoder
7
Y - Select Gates
8
V
PP
Switch/
Pump
Sense Amplifiers
Write/Erase-Bit
Compare and Verify
X - Decoder/Block Erase Control
Input
Buffer
Addr.
A0–A17/(A18)
A9
Buffer/
Latch
9
(10)
Addr.
Power
(Current)
Control
Counter
128KB Main Block
DQ15/(A - 1)
1
DQ8–DQ14
1
128KB Main Block
WP#
CE#
OE#
WE#
RP#
V
CC
DQ0–DQ7
4Mb
SMART 3 BOOT BLOCK FLASH MEMORY
3
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003, Micron Technology, Inc.All rights reserved.
V
PP
Output
Buffer
DQ15
Status
Register
Identification
Register
7
Output
Buffer
8
Output
Buffer
MUX
8
NOTE:
1. Does not apply to MT28F004B3.
4Mb
SMART 3 BOOT BLOCK FLASH MEMORY
Table 1:
44-PIN
SOP
NUMBERS
43
Pin Descriptions
40-PIN
TSOP
NUMBERS
9
48-PIN
TSOP
NUMBERS
11
SYMBOL
WE#
TYPE
Input
DESCRIPTION
Write Enable: Determines if a given cycle is a WRITE cycle.
If WE# is LOW, the cycle is either a WRITE to the command
execution logic (CEL) or to the memory array.
2
12
14
WP#
Input
Write Protect: Unlocks the boot block when HIGH if V
PP
=
V
PPH1
(3.3V) or
V
PPH2
(5V) and RP# = V
IH
during a
WRITE or ERASE. Does not affect WRITE or ERASE
operation on other blocks.
Chip Enable: Activates the device when LOW. When CE# is
HIGH, the device is disabled and goes into standby power
mode.
Reset/Power-Down: When LOW, RP# clears the status
register, sets the internal state machine (ISM) to the array
read mode and places the device in deep power-down
mode. All inputs, including CE#, are “Don’t Care,” and all
outputs are High-Z. RP# unlocks the boot
block and
12
22
26
CE#
Input
44
10
12
RP#
Input
overrides the condition of WP# when at V
HH
(12V), and
must be held at V
IH
during all other modes
of operation.
14
33
24
–
28
47
OE#
BYTE#
Input
Input
Output Enable: Enables data output buffers when LOW.
When OE# is HIGH, the output buffers are disabled.
Byte Enable: If BYTE# = HIGH, the upper byte is active
through DQ8–DQ15. If BYTE# = LOW, DQ8–DQ14 are High-
Z, and all data is accessed through DQ0–DQ7. DQ15/(A-1)
becomes the least significant address input.
Address Inputs: Select a unique, 16-bit word or 8-bit byte.
The DQ15/(A-1) input becomes the lowest order address
when BYTE# = LOW (MT28F400B3) to allow for a selection
of an 8-bit byte from the 524,288 available.
11, 10, 9, 8, 21, 20, 19,
7, 6, 5, 4,
18, 17, 16,
42, 41, 40, 15, 14, 8, 7,
39, 38, 37,
36, 6, 5, 4,
36, 35, 34, 3 3, 2, 1, 40,
13
31
–
25, 24, 23,
22, 21, 20,
19, 18, 8, 7,
6, 5, 4, 3, 2,
1, 48, 17
45
A0–A17/
(A18)
Input
DQ15/
(A-1)
DQ0–DQ7
15, 17, 19,
21, 24, 26,
28, 30
16, 18, 20,
22, 25, 27,
29
1
25-28, 32-35
–
11
29, 31, 33,
35, 38, 40,
42, 44
30, 32, 34,
36, 39, 41,
43
13
DQ8–
DQ14
V
PP
Input/ Data I/O: MSB of data when BYTE# = HIGH. Address Input:
Output LSB of address input when BYTE# = LOW during READ or
WRITE operation.
Input/ Data I/Os: Data output pins during any READ operation or
Output data input pins during a WRITE. These pins are used to
inputcommands to the CEL.
Input/ Data I/Os: Data output pins during any READ operation or
Output data input pins during a WRITE when BYTE# = HIGH. These
pins are High-Z when BYTE# is LOW.
Supply Write/Erase Supply Voltage: From a WRITE or ERASE
CONFIRM until completion of the WRITE or ERASE, V
PP
must be at
V
PPH1
(3.3V) or
V
PPH2
(5V). V
PP
= “Don’t
Care”
during all other operations.
23
13, 32
–
30, 31
23, 39
29, 37, 38
37
27, 46
9, 10, 15, 16
V
CC
V
SS
NC
Supply
Supply
–
Power Supply: +3.3V ±0.3V.
Ground.
No Connect: These pins may be driven or left unconnected.
09005aef8114a789
F45.fm - Rev. E 6/04 EN
4
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc. All rights reserved.
4Mb
SMART 3 BOOT BLOCK FLASH MEMORY
Table 2:
Truth Table (MT28F400B3)
1
RP#
CE#
H
X
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
OE# WE# WP#
X
X
L
L
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
L
L
L
L
L
L
X
X
H
H
H
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
H
H
H
H
H
H
X
X
X
X
X
X
X
X
X
X
X
X
X
H
X
X
H
X
H
X
X
X
X
X
X
X
BYTE#
X
X
H
L
X
X
X
X
H
L
X
X
X
X
X
H
H
L
L
X
H
L
H
L
H
L
A0
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
L
L
H
H
H
H
A9
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
V
ID
V
ID
V
ID
V
ID
V
ID
V
ID
FUNCTION
V
PP
X
X
X
X
X
X
V
PPH
X
V
PPH
V
PPH
X
X
V
PPH
V
PPH
X
V
PPH
V
PPH
V
PPH
V
PPH
X
X
X
X
X
X
X
DQ0–
DQ7
High-Z
High-Z
DQ8–
DQ14
High-Z
High-Z
DQ15/
A-1
High-Z
High-Z
H
Standby
L
RESET
READ
H
READ (word mode)
H
READ (byte mode)
H
Output Disable
WRITE/ERASE (EXCEPT BOOT BLOCK)
2
H
ERASE SETUP
3
H
ERASE CONFIRM
H
WRITE SETUP
4
H
WRITE (word mode)
H
WRITE (byte mode)
4
5
H
READ ARRAY
WRITE/ERASE (BOOT BLOCK)
2, 7
H
ERASE SETUP
V
HH
ERASE CONFIRM
3
3, 6
H
ERASE CONFIRM
H
WRITE SETUP
4
V
HH
WRITE (word mode)
4, 6
H
WRITE (word mode)
V
HH
WRITE (byte mode)
4
4, 6
H
WRITE (byte mode)
H
READ ARRAY
5
DEVICE IDENTIFICATION
8, 9
Manufacturer Compatibility
(word mode)
10
Manufacturer Compatibility
(byte mode)
Device (word mode, top boot)
10
Device (byte mode, top boot)
Device (word mode, bottom
boot)
10
Device (byte mode, bottom
boot)
NOTE:
Data-Out Data-Out Data-Out
Data-Out
High-Z
A-1
High-Z
High-Z
High-Z
20h
D0h
10h/40h
Data-In
Data-In
FFh
20h
D0h
D0h
10h/40h
Data-In
Data-In
Data-In
Data-In
FFh
89h
89h
70h
70h
71h
71h
X
X
X
Data-In
X
X
X
X
X
X
Data-In
Data-In
X
X
X
00h
High-Z
44h
High-Z
44h
High-Z
X
X
X
Data-In
A-1
X
X
X
X
X
Data-In
Data-In
A-1
A-1
X
–
X
–
X
–
X
H
H
H
H
H
H
1. L = V
IL
(LOW), H =
V
IH
(HIGH), X = V
IL
or
V
IH
(“Don’t Care”).
2. V
PPH
= V
PPH
1 (3.3V) or V
PPH
2 (5V).
3. Operation must be preceded by ERASE SETUP command.
4. Operation must be preceded by WRITE SETUP command.
5. The READ ARRAY command must be issued before reading the array after writing or erasing.
6. When WP# =
V
IH
, RP# may be at
V
IH
or
V
HH
.
7.
V
HH
= 12V.
8.
V
ID
= 12V; may also be read by issuing the IDENTIFY DEVICE command.
9. A1–A8, A10–A17 = V
IL
.
10. Value reflects DQ8–DQ15.
09005aef8114a789
F45.fm - Rev. E 6/04 EN
5
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2003 Micron Technology, Inc. All rights reserved.
京公网安备 11010802033920号
EEWORLD
