Operating Temperature Range ...........................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(V
CC
= full range, T
A
= -40°C to +85°C, unless otherwise noted. Typical values are at T
A
= +25°C and V
CC
= 3V.) (Note 1)
PARAMETER
V
CC
Range
SYMBOL
CONDITIONS
T
A
= 0°C to +70°C
T
A
= -40°C to +85°C
I
CC
MAX632_ only, V
CC
= 3.0V for V
TH
≤
2.93V,
V
CC
= 3.2V for V
TH
> 2.93V, no load
V
CC
= 5.5V, no load
T
A
= +25°C
Reset Threshold
V
TH
Table 1
T
A
= -40°C to +85°C
Reset Threshold Tempco
V
CC
to Reset Delay
Reset Active Timeout Period
RESET
Output Voltage
(MAX6326/MAX6328/
MAX6346/MAX6348)
RESET
Output Voltage
(MAX6326/MAX6346)
I
SINK
= 1.6mA, V
CC
> 2.1V, reset asserted
V
OL
I
SINK
= 100µA, V
CC
≥
1.2V, reset asserted
I
SOURCE
= 500µA, V
CC
= 3.2V, MAX6326 only
V
OH
I
SOURCE
= 800µA, V
CC
= 4.5V, V
TH
≤
4.38V
I
SOURCE
= 800µA, V
CC
= V
TH(MAX)
, V
TH
≥
4.5V
V
OH
RESET Output Voltage
(MAX6327/MAX6347)
V
OL
I
SOURCE
= 500µA, V
CC
≥
2.1V, reset asserted
I
SOURCE
= 50µA, V
CC
≥
1.2V, reset asserted
I
SINK
= 1.2mA, V
CC
≥
3.2V, reset not asserted,
MAX6327 only
I
SINK
= 3.2mA, V
CC
≥
4.5V, reset not asserted,
V
TH
≤
4.38V
I
SINK
= 3.2mA, V
CC
= V
TH(MAX)
, V
TH
≥
4.5V
RESET Threshold
Hysteresis
Open-Drain
RESET
Output
Leakage Current
Note 1:
Overtemperature limits are guaranteed by design and not production tested.
Seeing that ZTE's online written test is about to end, but my resume is still pending review, I am still a little panicked. In the past few days, I have also applied for some other R&D positions, incl...
It's like this. There are not many programs about FM62429 on the Internet. Most of them require money or upload. Is there anyone who can write a program to control it? I don't want ASM. I want C++. An...
When using MSP430f4270, when DAC outputs zero volt signal, there is a positive offset of about 1 millivolt. Please give me some advice on where to start solving this problem. Thank you....
Compilation warning:
This project was created using a version of compiler that is not currently installed: 6.0.3 [C2000]. Another version of the compiler will be used during build: 6.2.0. Please insta...
There are many components missing in the protel library, or I can't find them. I have to draw them myself. How do I draw the package? ? ? Please help...
DSP needs to communicate with the screen in SCI mode. There is no problem when querying and sending separately. After adding interrupt reception, the data sent by DSP is wrong, and there are many dupl...
With the rapid development of science and technology, especially the widespread application of digital technology and various ultra-large-scale integrated circuits, electronic equipment, especially...[Details]
Aromatic gases are widely present in food, medicine, cosmetics and various daily chemical products, such as snacks, liquor, spices, Chinese herbal medicines, plasters, perfumes, soaps, shampoos, et...[Details]
1 Introduction
PROFIBUS is an international, open, and manufacturer-independent fieldbus standard. It is widely used in manufacturing automation, process industry automation, and automatio...[Details]
introduction
MAX6636 is a multi-channel precision temperature monitor that can not only monitor local temperature, but also connect up to 6 diodes externally. Each channel has a programmable...[Details]
Abstract: Aiming at the needs of coal-rock acoustic emission signal monitoring system, a data acquisition circuit with 24-bit resolution and 16-channel synchronous data acquisition function is desi...[Details]
Only a small number of LED manufacturers can produce high-quality LEDs. For applications that are only used for simple indication, low-quality LEDs are sufficient. However, high-quality LEDs must...[Details]
1. Introduction
With the increasing popularity of fully automatic washing machines, consumers have higher and higher requirements for their environmenta...[Details]
0 Introduction
Under normal circumstances, the three-phase power in the power system is symmetrical, and they meet certain amplitude and phase conditions; but when the load changes, the syst...[Details]
Temperature compensated quartz crystal oscillator (TCXO) is widely used as a high-precision frequency source in communication systems, radar navigation systems, precision measurement and control sy...[Details]
1 Introduction to LED
With the development of science and technology, people have higher and higher requirements on automobile light sources. LED (Light Emitting Diode) has gradually attracted...[Details]
Currently, the commonly used solar cell technologies include monocrystalline silicon solar cells and polycrystalline silicon thin-film solar cells. Production process: Monocrystalline silicon solar...[Details]
1. Tips for charging UPS for the first time
After purchasing a new UPS, plug the UPS into the 220V mains power grid and charge it for at least 12 hours to ensure that the battery is fully char...[Details]
Measurement compatibility
It is very important to ensure the compatibility between the pressure sensor and its actual application. Before making a pressure sensor selection, the fo...[Details]
Traditionally, when using PLC to control stepper motors, a dedicated stepper motor control intelligent module is usually added to the PLC, and then connected to the drive power supply to realize th...[Details]
Stepper motors have been widely used in automatic or semi-automatic equipment such as CNC machine tools, medical equipment, and instruments. The usual way to control stepper motors with computers i...[Details]
Recruitment
京公网安备 11010802033920号
EEWORLD
