EEWORLDEEWORLDEEWORLD

Part Number

Search

P5-A82122

Description
Pushbutton Switch, SPST, Momentary-tactile, 10A, 28VDC, Solder Terminal, Panel Mount-threaded
CategoryMechanical and electronic products    switch   
File Size1MB,2 Pages
ManufacturerOTTO
Websitehttp://www.ottoexcellence.com
Environmental Compliance
Download Datasheet Parametric View All

P5-A82122 Overview

Pushbutton Switch, SPST, Momentary-tactile, 10A, 28VDC, Solder Terminal, Panel Mount-threaded

P5-A82122 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerOTTO
Reach Compliance Codeunknown
ECCN codeEAR99
Actuator length0.24 inch
Actuator stroke4.572 mm
Actuator typeCURVED TYPE
Body length or diameter19.05 mm
Casing type3/4-20
Center contact platingSILVER
Contact (AC) maximum rated load I5A@115VAC
Contact (AC) maximum rated R load10A@115VAC
Maximum contact current (AC)10 A
Maximum contact current (DC)10 A
Contact (DC) maximum rated R load10A@28VDC
Contact resistance0.025 mΩ
Maximum contact voltage (AC)115 V
Maximum contact voltage (DC)28 V
Dielectric withstand voltage1050VRMS V
Electrical life25000 Cycle(s)
End contact platingSILVER
JESD-609 codee4
Manufacturer's serial numberP5-A
Installation featuresPANEL MOUNT-THREADED
Maximum operating force17.57 N
Maximum operating temperature85 °C
Minimum operating temperature-55 °C
sealIP68
surface mountNO
Switch actionMOMENTARY-TACTILE
switch functionSPST
Switch typePUSHBUTTON SWITCH
Terminal surfaceGold (Au)
Terminal materialBRASS
Termination typeSOLDER
VANDAL RESISTANT PUSHBUTTONS
ALTERNATE ACTION, SEALED AGAINST DUST & MOISTURE
P5-V
VANDAL RESISTANT
PUSHBUTTONS
The P5-V switch gives you all the functionality of the P5 Alternate
Action switch with the added benefit of an aluminum security
level case and button or a stainless steel vandal resistant case
and button.
Push and the P5-V switch turns “on.” Push again and the
switch turns “off.” Positive tactile feedback is featured so the
operator is clearly aware the switch has been actuated. The
button returns to the original position after each actuation.
To guard against front panel splash and dirt the P5-V is sealed
at the button with OTTO’s patented “rolling sleeve” design.
The terminals are sealed with epoxy, providing a seal against
flux during wiring and behind panel dirt and moisture. The
combination of sealing provides smooth operation over a wide
temperature range. Watertight sealing to IP68S is also available.
We are able to provide custom button engraving with epoxy
ink backfill and other special characters, shrouded buttons,
contact configurations and materials to suit your application
requirements.
High Profile
Flat Button
High Profile
Curved Button
Features:
• Security (aluminum) or vandal resistant
(stainless steel) case & button
• Button sealed with patented “rolling sleeve” design
• Contact area sealed at case & terminals
• Watertight to IP68S or dusttight & moistureproof
to IP64
• Less than 25mΩ contact resistance
• Handles low level up to 10 amps
• 1 million mechanical cycle life
• RoHS & WEEE Compliant
Standard Characteristics/Ratings:
ELECTRICAL RATINGS:
Load
Resistive
Inductive
Lamp
Motor
DWV
Low Level
Electrical Life:
Mechanical Life:
Seal:
Operating Force:
Total Travel:
Overtravel:
Sea Level @
28VDC or 115VAC, 60/400Hz
10A
5A
1A
3A
1050Vrms
10mA @ 30mV
25,000 cycles
1,000,000 cycles
IP64 or IP68S
3.0 lbs. +1/-0.5 lb.
0.180 inches max
0.012 inches min
Operating Temp Range:
-55°C to +85°C
MATERIALS:
Case:
Button:
Terminals:
Terminal Hardware:
Mounting Hardware:
Anodized aluminum alloy or stainless steel
Anodized aluminum alloy or stainless steel
Brass with gold over silver
Screw, lockwasher and terminal lug when applicable
Hex nut or knurl nut, lockwasher and panel seal when applicable
PUSHBUTTONS
Specifications Subject To Change Without Notice
www.ottoexcellence.com
122
DC Motor Control
[table=98%] [tr][td][float=right] [/float] How does the electric vehicle controller automatically identify whether it has Hall or not???? How is self-learning achieved?????[/td][/tr] [/table]...
yanhuawei Industrial Control Electronics
The difference between RTOS interrupt and timer 2 interrupt when the μcosii system is transplanted to DSP
Recently I have been studying the porting of μcosii operating system to F28027. Currently I am writing the tick clock interrupt of the operating system. I personally thought that this tick clock inter...
sure220 DSP and ARM Processors
[RVB2601 creative development and application] 1. RGB three-color breathing light and key anti-shake
1. Routine testThe routine ch2601_rgb_marquee_demo provided by RVB2601 already has the GPIO control method and PWM control method of the RGB tricolor light, which was tested. However, there must be so...
vg552 XuanTie RISC-V Activity Zone
Need help?
I installed ISE13.1 and modelsim6.5 on Windows 7, but why can't I use them? Please help...
落叶的星空 FPGA/CPLD
msp430 JTAG emulator
I found a drawing of the msp430 JTAG emulator on the Internet, and soldered a board (IC: 74HC244N) according to the circuit in the drawing.But a connection error occurred when using IRA. Let’s see wha...
simonzhu Microcontroller MCU
Problems with setting interrupt vector
I am using 2407. Since I am in the stage of learning and debugging, I load programm frequently, so I set the board to microprocessor mode and put the program in external memory instead of burning flas...
gd88zjl Analogue and Mixed Signal

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2614  202  2393  764  103  53  5  49  16  3 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号