The structure of longer electrodes provides the wider welding area than the chip resistors with normal electrodes,
and this enhanced the solder welding strength.
2) Increased surge-resistance
This is achieved by Rohm’s original trimming technology plus resistive element patterning.
3) High-power tolerance
Two times of the rated power is guaranteed than the normal-electrode resistors.
4) ROHM resistors are ISO-9001 & ISO/TS16949 certified.
Design and specifications are subject to change without notice. Carefully check the specification sheet before using
or ordering it.
Applications
Automotive, industrial and power supply.
Ratings
Item
Rated power
Conditions
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
100
80
POWER LOAD (%)
Specifications
0.5W (1 /2W)
at 70°C
60
40
20
0
−55
0
70
100
155
AMBIENT TEMPERATURE (
°
C)
Fig.1
Rated voltage
Rated current
The voltage rating is calculated by the following equation.
E=
I =
P
×
R
P/R
E : Rated voltage (V)
I : Rated current (A)
P : Rated power (W)
R : Nominal resistance (Ω)
Nominal resistance
Operating temperature
See Table 1.
−55°
C to
+ 155°C
1/4
LTR10
Resistors
Table 1
Resistance range
(Ω)
Resistance
tolerance
F (±1%)
J (±5%)
Special part number
Resistance temperature coefficient
(ppm/°C)
0.047
0.1
R
R
10
0.1
S
L
±150
Before using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
Characteristics
Item
Guaranteed value
Resistor type
Test conditions (JIS C 5201-1)
JIS C 5201-1 4.5
Voltage : A
Measuring method : Measure under termination by 4 probes
Under termination
Terminal
Resistance
F :
±1%
J :
±5%
Variation of resistance
with temperature
See Table.1
JIS C 5201-1 4.8
Measurement :
−55
/
+25
/
+125°C
JIS C 5201-1 4.13
Rated voltage (current)
×
2.5, 2s.
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235±5°C
Duration of immersion : 2.0±0.5s.
JIS C 5201-1 4.18
Soldering condition : 260±5°C
Duration of immersion : 10±1s.
JIS C 5201-1 4.19
Test temp. :
−55°C
to
+125°C
5cyc
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 1,000h to 1,048h
JIS C 5201-1 4.25.1
Rated voltage (current), 70°C
1.5h : ON
−
0.5h : OFF
Test time : 1,000h to 1,048h
JIS C 5201-1 4.25.3
155°C
Test time : 1,000h to 1,048h
JIS C 5201-1 4.29
23±5°C, Immersion cleaning, 5±0.5min.
Solvent : 2-propanol
JIS C 5201-1 4.33
Overload
±
(2.0%+0.1Ω)
Solderability
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
±
(1.0%+0.005Ω)
No remarkable abnormality on the appearance.
±
(1.0%+0.005Ω)
Resistance to
soldering heat
Rapid change of
temperature
Damp heat, steady state
±
(3.0%+0.005Ω)
Endurance at 70°C
±
(3.0%+0.005Ω)
Endurance
±
(3.0%+0.005Ω)
Resistance to solvent
Bend strength of
the end face plating
±
(0.5%+0.005Ω)
Without open.
2/4
LTR10
Resistors
Dimensions
(Unit : mm)
W
a
R033
b
L
3
2
4
5
1
No.
1
2
3
7
4
5
6
Material
Resistive element
Silver thick film electrode
Silver thick film side electrode
Nickel electrode
Sn electrode
Overcoating
Alumina substrate
L
6
t
Size code
2012 (0805)
L
1.2
±
0.1
W
2.0
±
0.1
t
0.55
±
0.1
a
0.35
±
0.1
b
0.25
±
0.1
7
Packaging
Reel
Taping
P
0
P
2
P
1
φD
0
E
F
W
08
06
04
02
02
04
06
08
A
B
D
A
0
Heat crimp cover/Tape
Thick paper (Underside paper tape) Chip resistor Square punchout hole
mount
T
2
C
Label
EIAJ ET-7200B compliant
(Unit: mm)
(Unit: mm)
A
φ180
0
−1.5
B
φ60
+1
0
9
C
+1.0
0
D
φ13±0.2
W
8.0±0.3
D
0
+0.1
φ1.5
0
F
3.5±0.05
P
0
4.0±0.1
E
1.75±0.1
P
1
4.0±0.1
A
0
1.65
+0.2
−0.1
B
0
2.4
+0.2
−0.1
P
2
2.0±0.05
T
2
Max. 1.1
3/4
LTR10
Resistors
Part designation
L T R 1 0
Part No.
E Z P
J
F
J
±
5%
±
1%
L
Nominal resistance
Resistance code, 3 or 4 digits.
Resistance tolerance
Resistance
tolerance
J
F
:
:
Resistance
code
3 digits
4 digits
Packaging Specifications Code
Part No.
LTR10
Code
EVH
Resistance tolerance
F(
±
1%)
J(
±
5%)
Packaging specifications
Paper tape (4mm Pitch)
Reel
φ180mm
(7inch)
Basic ordering unit
(pcs)
5,000
Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B"
: Standard product
4/4
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level
of reliability and the malfunction of which would directly endanger human life (such as medical
[i=s]This post was last edited by chenlijuan on 2017-10-22 12:02[/i] I received the CH554 development board a few days ago.This morning I wrote a program to make the LED light flash according to the e...
[align=left]If the other person can bring pleasure to oneself, there will be a force that drives oneself to approach him. [/align][align=left]We also hate those who hate us. [/align] [align=left] [/al...
PV DC fuses are safety devices used to protect PV panels, inverters, and DC loads. To ensure their safety and reliability, they must be UL248 certified.
Before applying for UL248 certifi...[Details]
Electric vehicles are currently gaining momentum, but this is just a facade. Fuel-powered vehicles remain unchallenged. While electric vehicles boast unique advantages in environmental emissions an...[Details]
As the number of cars increases, environmental pressures are also increasing. At this time, some people are saying that new energy vehicles are energy-efficient and environmentally friendly, and ar...[Details]
With the rapid development of technology, automotive intelligence is increasing at an unprecedented rate. This not only enhances vehicle functionality and comfort, but also places higher deman...[Details]
New energy pure electric vehicles generally accelerate faster than comparable fuel-powered vehicles, both from a standing start and while accelerating. Many believe this is simply due to the motor'...[Details]
With the rapid advancement of automation technology, collaboration between robots is no longer just science fiction. Imagine dozens of machines moving goods in a warehouse without interfering with ...[Details]
Core point: The automotive industry chain and the humanoid robot industry have collaborative advantages in hardware, software, and scenarios. Upstream and downstream companies in the automotive ind...[Details]
On August 21st, Zhiyuan Robotics revealed at its first partner conference that it expects shipments to reach thousands of units this year and tens of thousands next year. The company hopes to reach...[Details]
Pure electric vehicles, structurally speaking, have components such as a power battery. In addition to the power battery, a small battery also powers some low-voltage electrical components and even...[Details]
With the advent of the electric car era, the number of pure electric vehicles has increased significantly, but many car owners do not know how to properly maintain pure electric vehicles. In additi...[Details]
Electric vehicles are powered by electricity, and charging is a device that supplements the vehicle's energy source. It is common to need to recharge the vehicle when driving. But can you charge th...[Details]
In daily life, power transformers have different functions and uses due to different usage scenarios. The most common ones can be divided into: control transformers, isolation transformers, rectifi...[Details]
In this final installment of a five-part blog series, I will discuss noise in op amps driving headphone loads and some techniques for reducing it. Previous posts have discussed headphone load power...[Details]
Introduction: Traditionally, lead-acid batteries have primarily been used to provide backup power and power regulation based on location. In typical applications, the battery's actual use (discharg...[Details]
The intelligent
dust monitoring system intelligently monitors dust concentrations at and around construction sites. All concentration values are transmitted to a cloud server for
cloud co...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
