CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.
NOTE:
1.
θ
JA
is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
PARAMETER
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
Turn-OFF Time
t
OFF1
t
OFF2
OFF Isolation, OIRR (Note 5)
V+ = +15V, V- = -15V, V
L
= +5V, GND, T
A
= +25°C
TEST CONDITIONS
MIN
(Notes 2, 6)
TYP
(Note 3)
MAX
(Notes 2, 6) UNITS
See Figure 1
V
S
= 10V, R
L
= 1kΩ, C
L
= 35pF
-
460
-
ns
-
-
V
IN
= 5V, R
L
= 1kΩ, C
L
= 15pF, V
S
= 1V
RMS
,
f = 100kHz
V
D
= V
S
= 0V, V
IN
= 5V, f = 1MHz
-
-
-
-
-
360
450
70
-90
5
5
16
-
-
-
-
-
-
-
ns
ns
dB
dB
pF
pF
pF
Crosstalk (Channel-to-Channel), CCRR
Source OFF-Capacitance, C
S(OFF)
Drain OFF-Capacitance, C
D(OFF)
Channel ON-Capacitance, C
D(ON)
+ C
S(ON)
DIGITAL INPUT CHARACTERISTICS
Input Current with Voltage High, I
IH
V
IN
= 2.4V
V
IN
= 15V
-1.0
-
-1.0
-0.0004
0.003
-0.0004
-
1.0
-
µA
µA
µA
Input Current with Voltage Low, I
IL
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
Drain-Source ON-Resistance, r
DS(ON)
Source OFF Leakage Current, I
S(OFF)
V
IN
= 0V
-15
V
D
= ±10V, I
S
= 1mA, V
IN
= 0.8V
V
IN
= 2.4V
V
S
= 14V, V
D
= -14V
V
S
= -14V, V
D
= 14V
-
-
-5.0
-
-5.0
-
-5.0
-
150
0.01
-0.02
0.01
-0.02
0.1
-0.15
15
175
5.0
-
5.0
-
5.0
-
V
Ω
nA
nA
nA
nA
nA
nA
Drain OFF Leakage Current, I
D(OFF)
V
S
= -14V, V
D
= 14V
V
S
= 14V, V
D
= -14V
Drain ON Leakage Current, I
D(ON)
(Note 4)
V
IN
= 0.8V
V
S
= V
D
= 14V
V
S
= V
D
= -14V
3
FN3118.5
November 19, 2007
DG211
Electrical Specifications
PARAMETER
POWER SUPPLY CHARACTERISTICS
Positive Supply Current, I+
Negative Supply Current, I-
Logic Supply Current, I
L
NOTES:
2. The algebraic convention whereby the most negative value is a minimum, and the most positive is a maximum, is used in this data sheet.
3. For design reference only, not 100% tested.
4. I
D(ON)
is leakage from driver into ON switch.
V
S
-
5. OFF Isolation
=
20 log
-------
, V
S
=
Input to OFF switch, V
D
=
output .
V
D
6. Parts are 100% tested at +25°C. Over-temperature limits established by characterization and are not production tested.
V
IN
= 0V or 2.4V
-
-
-
0.1
0.1
0.1
10
10
10
µA
µA
µA
V+ = +15V, V- = -15V, V
L
= +5V, GND, T
A
= +25°C
(Continued)
TEST CONDITIONS
MIN
(Notes 2, 6)
TYP
(Note 3)
MAX
(Notes 2, 6) UNITS
Test Circuits and Waveforms
Switch output waveform shown for V
S
= constant with logic
input waveform as shown. Note the V
S
may be + or - as per
switching time test circuit. V
O
is the steady state output with
switch on. Feedthrough via gate capacitance may result in
spikes at leading and trailing edge of output waveform.
京公网安备 11010802033920号
EEWORLD
