VEM14GT28-38.880-1.0/-10+60 datasheet, PDF

Datasheet> All Categories > Passive components> oscillator> VEM14GT28-38.880-1.0/-10+60

VEM14GT28-38.880-1.0/-10+60: DescriptionOscillator,; CategoryPassive components oscillator; File Size136KB，1 Pages; ManufacturerEuroquartz; Websitehttp://www.euroquartz.co.uk/; Environmental Compliance

Download Datasheet Parametric View All

VEM14GT28-38.880-1.0/-10+60 Overview

Oscillator,

VEM14GT28-38.880-1.0/-10+60 Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	Euroquartz
Reach Compliance Code	compliant
Other features	SYMMETRY OF 55/45% & STD CONTROL VOLTAGE OF 0.5 TO 2.5V ALSO AVAILABLE
Ageing	1 PPM/FIRST YEAR
Maximum control voltage	5.5 V
Minimum control voltage	3.5 V
maximum descent time	10 ns
Frequency Adjustment - Mechanical	NO
Frequency offset/pull rate	6 ppm
frequency stability	1%
Installation features	THROUGH HOLE MOUNT
Nominal operating frequency	38.88 MHz
Maximum operating temperature	60 °C
Minimum operating temperature	-10 °C
Oscillator type	HCMOS
Output load	15 pF
physical size	20.2mm x 12.8mm x 7.5mm
longest rise time	10 ns
Nominal supply voltage	2.8 V
surface mount	NO
maximum symmetry	60/40 %

Preview

Download Datasheet

View All

EURO

QUARTZ

CMOS, 14 pin DIL, MHz Range

14 pin DIL industry-standard package

Wide frequency range: 1.25MHz to 156.0MHz

Supply voltage 2.8, 3.0, 3.3 or 5.0 Volts

Frequency stability from ±1ppm over -30 to +75°C

RoHS compliant

EM14GT TCXO

1.25MHz to 156.0MHz

EM14GT - OUTLINES AND DIMENSIONS

DESCRIPTION

EM14GT series TCXOs are packaged in the industry-standard 14 pin

DIL package. With squarewave (CMOS) output, tolerances are

available from ±1.0ppm over -30° to +75°C. The part has a 0.01mF

decoupling capacitor built in.

SPECIFICATION

Product Series Code

TCXO:

VCTCXO:

Frequency Range:

Output Waveform:

Initial Calibration Tolerance:

Standard Frequencies:

EM14GT

VEM14GT

1.25MHz to 156.0MHz

Squarewave, HCMOS

<±1.0ppm at +25°±2°C

10.0, 12.8, 13.0, 14.4, 15.36,

16.384, 19.2, 19.440, 19.68,

25.0, 20.0, 27.0, 38.880,

40.0, 77.760, 125.0, 155.520

(Partial

list)

See table

±1.0 ppm max. first year

±0.3 ppm max. ±5% change

±0.3 ppm max. ±10% change

±1.0ppm max. for one reflow

(Measured

after 24 hours)

±3ppm minimum

+2.8, +3.0, +3.3 or +5.0V

(See

table)

Logic High: 90% Vdd min.

Logic Low: 10% Vdd max.

10ns max.

50%±10% standard,

50%±5% option

5ms typical, 10ms max.

See table below

15pF

-55~+125°C

Operating Temperature Range:

Frequency Stability

vs. Ageing:

vs. Voltage Change:

vs. Load Change:

vs. Reflow (SMD type):

Mechanical Frequency Tuning:

Supply Voltage:

Output Logic Levels:

Rise and Fall Times:

Duty Cycle:

Start-up Time:

Current Consumption:

Output Load:

Storage Temperature:

INPUT VOLTAGE & CURRENT CONSUMPTION

Input Voltage/

Frequency

8.192MHz

10.0MHz

77.760MHz

155.520MHz

+2.8V

2mA

3mA

14mA

26mA

+3.0

+3.3V

2mA

4mA

17mA

35mA

+5.0 V

5mA

7mA

32mA

50mA

SSB PHASE NOISE at 25°C

FREQUENCY STABILITY

Frequency Stability (ppm)

0 ~ +50

-10 ~ +60

Temperature

Range (°C)

-20 ~ +70

-30 ~ +75

-40 ~ +85

±0.5

ASK

±1.0

±1.5

±2.0

±2.5

Part =

EM14GT33

Offset

at 10.0Mhz

(dBc/Hz)

at 155.250Mhz

(dBc/Hz)

10Hz

-115

-72

100Hz

-135

-110

1kHz

-148

-125

10kHz

-152

-132

100kHz

-155

-125

PART NUMBERING SCHEDULE

Example:

= available, x = not available, ASK = call Technical Sales

EM14GT33-38.880-2.5/-30+75

VEM14GT VOLTAGE CONTROL SPECIFICATION

Control Voltage:

Standard = +1.5±1.0Volts for all input

voltages.

(Contact technical sales if

+2.5±2.0 Volts is required.)

Frequency Deviation: ±6.0 ppm min. (Vcon = +4.5V±1.0V)

Slope Polarity:

Positive

(increase of control voltage increases

output frequency.)

Input Impedance:

50k minimum

Modulation Bandwidth: 20kHz minimum

Linearity:

±10% maximum

Series Description

TCXO = EM14GT

VCTCXO = VEM14GT

Supply Voltage

28 = 2.8VDC

3 = 3.0VDC

33 = 3.3 VDC

5 = 5.0 VDC

Frequency (MHz)

Stability over OTR (±ppm)

Operating Temperature Range (OTR) (°C)

Lower and upper limits.

EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE

Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 info@euroquartz.co.uk www.euroquartz.co.uk

Recommended Resources

Grain temperature measuring instrument circuit

Telephone flashing light circuit monitor circuit diagram

RTD equipped with ±12V power supply transmit/receive circuit

Small power uninterruptible power supply circuit diagram

Multi-channel wired intercom

OTL gate negative voltage doubler rectifier circuit (for tube power amplifier)

core1081 camera module: First, I will post a picture of the effect, which is quite ideal ^_^^_^! 1: First, let's summarize the technologies used: (1) DCMI interface: STM32F1 does not have it, but it is added by STM32F2, whic...; 左左凯 RF/Wirelessly

The serial port control under wince downloaded from the Internet can only output but not receive! Waiting online!: Below is the program source code. When the computer sends data, wince cannot receive the data at all. However, when wince sends data, the computer can receive it normally! During debugging, I found th...; chenjian3 Embedded System

Bluetooth transceiver IC test: The first official version of the Bluetooth specification, version 1.0, was released in July 1999. Since then, many manufacturers have launched cost-effective integrated circuit chips that support Blu...; fly RF/Wirelessly

If you don’t understand millimeter wave, ask: the latest application of millimeter wave radar in automobiles: [i=s]This post was last edited by qwqwqw2088 on 2019-4-18 20:43[/i] [align=left][color=rgb(85, 85, 85)][font="][size=4]1. What is the response time of TI millimeter wave radar?[/size][/font][/color][/...; qwqwqw2088 Analogue and Mixed Signal

[Beginner's Note] Popular Science of MSP430 Integrated Development Environment: When we come into contact with a type of MCU, we are all concerned about the development environment required to develop the MCU.This question is often asked by netizens on the forum. In this post, I ...; wstt Microcontroller MCU

Why does blocking touch screen wakeup in WINCE5.0 have no effect?: In the touch driver, after applying for the system interrupt number, I call KernelIoControl(IOCTL_HAL_DISABLE_WAKE, &gIntrTouch, sizeof(gIntrTouch), NULL, 0, NULL); I want to block the touch screen wa...; marshaljeff Embedded System

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components