EEWORLDEEWORLDEEWORLD

Part Number

Search

8D0-11F05BC022

Description
MIL Series Connector, 5 Contact(s), Aluminum Alloy, Female, Crimp Terminal, Receptacle,
CategoryThe connector    The connector   
File Size692KB,12 Pages
ManufacturerEsterline Technologies Corporation
Environmental Compliance
Download Datasheet Parametric View All

8D0-11F05BC022 Overview

MIL Series Connector, 5 Contact(s), Aluminum Alloy, Female, Crimp Terminal, Receptacle,

8D0-11F05BC022 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerEsterline Technologies Corporation
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresSTANDARD: MIL-DTL-38999, EMI SHIELDED, POLARIZED
Back shell typeSOLID
Body/casing typeRECEPTACLE
Connector typeMIL SERIES CONNECTOR
Contact to complete cooperationNICKEL
Contact completed and terminatedNickel (Ni)
Contact point genderFEMALE
Contact materialNOT SPECIFIED
Coupling typeTHREADED
DIN complianceNO
empty shellYES
Environmental characteristicsENVIRONMENT/FLUID RESISTANT
Filter functionNO
IEC complianceNO
MIL complianceYES
Plug informationMULTIPLE MATING PARTS AVAILABLE
Mixed contactsNO
Installation typeCABLE AND PANEL
OptionsGENERAL PURPOSE
Shell surfaceNICKEL PLATED
Shell materialALUMINUM ALLOY
Housing size11
Termination typeCRIMP
Total number of contacts5
8D Series
D38999 Aluminum Series
Connector part numbers
Basic Series
8D
0
-
1
1
W
35
P
N
Shell style:
0:
Square flange receptacle
1:
In line receptacle
7:
Jam nut receptacle
5: Plug with RFI shielding
Also available:
.
Square flange receptacle with clinch nuts (see page 80)
.
Jam nut receptacle with double flange (see page 83)
Type:
None:
Connectors with standard crimp contacts.
L: Receptacle with long PC tail (male and female size #22D, #20).
C: Receptacle with short PC tail (male and female #22D, #20, #16).
S: Receptacle with specific PC tail (male et female #22D)
W: Receptacle with male contacts #22D for wire wrap (3 wraps)
T:
Receptacle with male contacts #20 for wire wrap (2 wraps)
P:
Receptacle with solder cup - only available for Reinforced sealing Series (see
page 75) - male and female size #22D; male #16 & #1
2; female #16 & #1
2
and male female #20 please consult us
Shell size: 09, 1 , 1 15, 1 1 21 23, 25
1 3,
7, 9, ,
Plating:
W:
Olive drab cadmium
F: Nickel
ZC:
Green zinc cobalt
Z: Black zinc nickel
Contact layout:
See pages 1 to 16
3
Contact type:
P:
Pin
A:
Connector supplied less pin contact or with specific contacts (connector marking: A + orientation)
S:
Socket
B:
Connector supplied less socket contact or with specific contacts (connector marking: B + orientation)
Orientation: N, A, B, C, D, E
(see page 64)
Specification:
046:
Tinned straight PC tail
251:
Connector provided with power contacts (layouts with contact #8)
022: Fuel tank
Special custom:
None:
Standard plastic cap
M:
Antistatic plastic cap
L: For P or S contact type only, connectors delivered without contacts, connectors marking P or S plus orientation
-
-
L
22
DFM should not be limited to chips, PCB needs it more
We all know that even if the silicon is 100% perfect, if any one component of the chip-to-chip communication link (such as the package, connector or circuit board) is damaged, the target system may st...
clj2004000 PCB Design
Report Forum
I've been busy making an amplifier recently, so I don't have time to share my experience with M3 with you. The information is not very valuable (I think the most valuable ones have been posted), and I...
heavenji Microcontroller MCU
Introduction to Intel Embedded Systems Invitational Competition
[i=s]This post was last edited by paulhyde on 2014-9-15 09:01[/i] The "Intel Cup Undergraduate Electronic Design Competition - Embedded System Special Invitational Competition" is part of the National...
open82977352 Electronics Design Contest
Adjustment of basic idle speed of electronically controlled vehicles 3
(2006-04-04 13:20:26 ) e. Turn off the engine after adjusting the basic idle speed, and then clear the fault code (35#) stored in the computer after disconnecting the ISCV circuit. Methods for clearin...
frozenviolet Automotive Electronics
What is the principle of transformer leakage inductance? Why do we need to short-circuit the secondary coil of the transformer when testing leakage inductance?
[size=4] When we use a bridge to test the leakage inductance of a transformer, we need to short-circuit the secondary side, and the inductance obtained by testing the primary side is the leakage induc...
qwqwqw2088 Analogue and Mixed Signal
How to choose air conditioner
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 20:01[/i] [color=#000000] [/color][/size][color=#000000][font=宋体][size=10.5pt]1. Look at the noise value[/size][/font] [font=宋体][size=10.5...
zhou369506992 Mobile and portable

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2108  2816  53  2268  163  43  57  2  46  4 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号