• Transformer Coupled Across 70 ohms, Measured on Stub:
• BU-63147/157XX-XX0
• BU-63147X3-XX2 (Note 9)
Output Noise, Differential (Direct Coupled)
Output Offset Voltage, Transformer Coupled Across 70 ohms
Rise/Fall Time
• BU-63147/157X3
• BU-63147X4
LOGIC
V
IH
V
IL
I
IH
Tx
Data In
, Tx
Inhibit
, Rx
Strobe
I
IL
Tx
Data In
, Tx
Inhibit
, Rx
Strobe
V
OH
(Vcc=4.75V,I
OH
=max)
V
OL
(Vcc=4.75V,I
OH
=max)
I
OL
I
OH
6
18
20
-250
100
200
7
20
22
150
150
250
9
27
27
10
250
300
300
Vp-p
Vp-p
Vp-p
mVp-p, diff
mVp-p, diff
ns
ns
2.0
20
-100
2.4
0.4
3.4
-3.4
0.8
100
-20
V
V
µA
µA
V
V
mA
mA
POWER SUPPLY REQUIREMENTS
Voltages/Tolerances
• +5V
Current Drain (Total Hybrid)
BU-63147/157/XX-XX0
• Idle (Both Channels)
• 25% Transmitter Duty Cycle (One Channel)
• 50% Transmitter Duty Cycle (One Channel)
• 100% Transmitter Duty Cycle (One Channel)
BU-63147/X3-XX2
• Idle (Both Channels)
• 25% Transmitter Duty Cycle (One Channel)
• 50% Transmitter Duty Cycle (One Channel)
• 100% Transmitter Duty Cycle (One Channel)
4.75
5.0
80
199
286
455
80
210
308
500
5.25
100
229
348
535
100
240
370
580
V
mA
mA
mA
mA
mA
mA
mA
mA
Data Device Corporation
www.ddc-web.com
3
BU-63147
P-07/12-0
TABLE 1. BU-63147/157 SPECIFICATIONS (CONT.)
PARAMETER
POWER DISSIPATION (NOTE 10)
Total Hybrid
BU-63147/157/XX-XX0
• Idle (Both Channels)
• 25% Transmitter Duty Cycle (One Channel)
• 50% Transmitter Duty Cycle (One Channel)
• 100% Transmitter Duty Cycle (One Channel)
BU-63147/X3-XX2
• Idle (Both Channels)
• 25% Transmitter Duty Cycle (One Channel)
• 50% Transmitter Duty Cycle (One Channel)
• 100% Transmitter Duty Cycle (One Channel)
Hottest Die
BU-63147/157/XX-XX0
• Idle (One Channel)
• 25% Transmitter Duty Cycle (One Channel)
• 50% Transmitter Duty Cycle (One Channel)
• 100% Transmitter Duty Cycle (One Channel)
BU-63147/X3-XX2
• Idle (One Channel)
• 25% Transmitter Duty Cycle (One Channel)
• 50% Transmitter Duty Cycle (One Channel)
• 100% Transmitter Duty Cycle (One Channel)
THERMAL
• Thermal Resistance, Junction-to-Case, Hottest Die (θ
JC
)
• Operating Junction Temperature
• Storage Temperature
• Lead Temperature (soldering, 10 sec.)
PHYSICAL CHARACTERISTICS
Size
36-Pin DIP
36-Lead Flat pack
Weight
MIN
TYP
MAX
UNITS
0.4
0.65
0.73
0.88
0.4
0.7
0.84
1.1
0.2
0.43
0.59
0.78
0.2
0.48
0.7
1.00
0.5
0.8
1.04
1.28
0.5
0.85
1.15
1.50
0.25
0.6
0.84
1.13
0.25
0.65
0.95
1.35
12
150
150
+300
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
W
°C/W
°C
°C
°C
-55
-65
1.900 x .800 x .205
(48.26 x 20.32 x 5.21)
1.900 x .800 x .200
(48.26 x 20.32 x 5.08)
0.6
(17)
in.
(mm)
in.
(mm)
oz
(g)
Notes:
Notes 1 through 6 are applicable to the Receiver Differential Resistance and Differential Capacitance specifications:
(1) Specifications include both transmitter and receiver (assumed tied together externally).
(2) Impedance parameters are specified directly between pins TX/RX A(B) and TX/RX A(B) hybrid.
(3) It is assumed that all power and ground inputs to the hybrid are connected and that the hybrid case is connected to ground for the impedance measurement.
(4) The specifications are applicable for both unpowered and powered conditions.
(5) The specifications assume a 2 volt rms balanced, differential, sinusoidal input. The applicable frequency range is 75 kHz to 1 MHz.
(6) Minimum resistance and maximum capacitance parameters are guaranteed over the operating range, but are not tested.
(7) The Threshold Level, as referred to in this specification, is meant to be the maximum peak-to-peak voltage (measured on the data bus) that can be applied to the
receiver's input without causing the output to change from the OFF state.
(8) Assumes a common mode voltage within the frequency range of dc to 2 MHz, applied to pins of the isolation transformer on the stub side (either direct or transformer
coupled), and referenced to transceiver ground. Transformer must be a DDC recommended transformer or other transformer that provides an equivalent minimum
CMRR.
(9) MIL-STD-1760 requires minimum output voltage of 20 Vp-p on the stub connection. The -XX2 option is
not
available for the BU-63147X4 or BU-63157 versions.
(10) Power dissipation specifications assume a transformer coupled configuration, with external dissipation (while transmitting) of 0.14 watts for the active isolation trans-
former, 0.08 watts for the active coupling transformer, 0.45 watts for each of the two bus isolation resistors, and 0.15 watts for each of the two bus termination resistors.
(11) Assuming the use of isolation transformers with the turns ratios shown in Figure 3 and in the absence of common mode signal on the 1553 stub, this equates to a
nominal stub voltage of 38 Volts
PK-to-PK
transformer-coupled, or 53 Volts
PK-to-PK
direct-coupled.
Data Device Corporation
www.ddc-web.com
4
BU-63147
P-07/12-0
TABLE 2. BU-63157 RADIATION SPECIFICATIONS*
PART NUMBER
BU-63157X3
TOTAL DOSE
100 KRAD
SINGLE EVENT
LATCHUP
IMMUNE
INTRODUCTION
The BU-63147/157 is a dual redundant transmitter and receiver
packaged in a 36-pin DDIP or flat pack. It is directly compatible to
Harris 15530 encoder/decoder and has internal (factory preset)
threshold levels. The dual transceiver only requires +5V power
and conforms to MIL-STD-1553A and 1553B. For McAir compat-
ibility, versions are available with rise/fall times of 200 to 300
nsec.
Figure 3 illustrates the connection between a BU-63147/157
transceiver and a MIL-STD-1553 Data Bus. After transformer
isolating the transceiver, it can be either direct coupled (short
stub) or transformer coupled (long stub) to the Data Bus.
*Note: Radiation parameters specified on this data sheet are derived from initial
qualification testing by DDC and published data from ASIC manufacturers. These
devices have not been evaluated for compliance to the RHA requirements stipu-
lated in MIL-PRF-38534, Appendix G.
TABLE 3. HIGH RELIABILITY SCREENING OPTIONS
FOR BU-63157
ELEMENT EVALUATION
Visual Inspection:
Integrated Circuits
Transistor & Diodes
Passive Components
METHOD
TRANSMIT OPERATING MODE
MIL-STD-883, Method 2010 Condition A
MIL-STD-750, Method 2072 and 2073
MIL-STD-883, Method 2032 Class S
SEM Analysis for Integrated MIL-STD-883, Method 2018
Circuits
Element Evaluation:
Visual, Electrical, Wire
Bondability, 24-Hour
Stabilization Bake, 10
Temperature Cycles,
5000 g’s constant accelera-
tion, 240-Hour Powered
Burn-In and 1000-Hour Life
Test (Burn-In and 1000-
Hour Life Test are Only
Required for Active
Components.)
ASSEMBLY & TEST
Particle Impact Noise
Detection (PIND)
320-Hour Burn-In
(Standard on this device)
100% Non-Destructive
Wirebond Pull
(Standard on this device)
Radiographic (X-Ray)
Analysis
QCI TESTING
Extended Temperature
Cycling:
20 Cycles Including
Radiographic (X-Ray)
Testing
Moisture Content Limit of
5000 PPM
MIL-STD-883, Method 2020
Condition A
MIL-STD-883, Method 1015
The transmitter section accepts encoded TTL data and converts
it to phase-modulated bipolar form using a waveshaping network
and driver circuits. The driver outputs TX DATA OUT and TX DATA
OUT are transformer coupled to the Data Bus.
The transmitter output terminals can be put into a high imped-
ance state by setting INHIBIT high, or setting TX DATA IN and TX
DATA IN to the same logic level. The operating modes are shown
in TABLE 4.
The transceivers are able to operate in a “wraparound” mode.
This allows output data to be monitored by the receiver section
and returned to the decoder where it is checked for errors.
MIL-PRF-38534
TABLE 4. TRANSMIT OPERATING MODE
TX DATA IN
X
0
0
MIL-STD-883, Method 2023
1
1
MIL-STD-883, Method 2012
TX DATA IN
X
0
1
0
1
TX INHIBIT
H
X
L
L
X
DRIVER OUTPUT
OFF (NOTE)
OFF
TX DATA OUT ON,
TX DATA OUT OFF
TX DATA OUT ON,
TX DATA OUT OFF
OFF
NOTE: DRIVER OUTPUT terminals are in the high impedance mode during
Hehe, I've been in a bad state recently. I came back from hiking yesterday and started sleeping. I woke up at noon today to eat, and then continued sleeping until now. So the photos are a little late....
Some netizens said they wanted to learn Ledit but couldn't find the information. Here I specially present the precious information to teach you how to learn Ledit step by step. Please download it if y...
I posted the source code as scheduled. I had planned to do storage before, but now I have to give up because I don't have time. I have to go out and find a job, haha!...
There are two ways to store values in DSP: fixed-point representation and floating-point representation.
The corresponding DSP chips are divided into two types: fixed-point DSP chips and floating-poin...
Brand new equipment, only opened for inspection. Original price 3,600 yuan, sold for 2k yuan. If you need, please contact: QQ: 46365030 Intel Atom fanless embedded industrial computer, 1 x LAN, 2 x CO...
[color=#000][font=宋体, "][size=13px]is a decaying forward signal, which is similar to a gradually decaying sine wave. [/size][/font][/color][color=#000][font=宋体, "][size=13px]Its duration is about 0.2 ...
Introduction to the principles of speech recognition technology
Automatic speech recognition (ASR) technology aims to enable computers to understand human speech and extract the textual inform...[Details]
We are entering a new era where people are increasingly affordably equipped with more electronic gadgets. Electronics have become essential to our lives. For example, the average consumer now owns ...[Details]
Recently,
Xpeng Motors and Xinlian Integrated Circuit jointly announced the mass production of China's first hybrid silicon carbide product.
Designed and developed by Xpeng Motors and joint...[Details]
On August 25th, SK Hynix announced that it has completed development and entered mass production of its 321-layer, 2Tb QLC NAND flash memory product. This achievement marks the world's first applic...[Details]
introduction
The concept of the smart home is gradually developing and gaining market acceptance. We believe its ultimate form lies in the interconnection of all home appliances through open i...[Details]
introduction
According to the China Fire Statistics Yearbook, electrical fires accounted for more than 30% of fire accidents in the past decade, and the trend is increasing year by year. They ...[Details]
Electric vehicles are now widespread, but they've brought with them a host of problems, the most prominent of which is charging. Small electric vehicles (EVs) are a new form of transportation in a ...[Details]
There are basically three causes of spontaneous combustion of electric vehicles: The first is that the battery components are punctured or suffer fatal damage due to a collision accident, and part ...[Details]
A multilevel inverter converts a DC signal into a multilevel staircase waveform. Instead of a straight positive-negative output waveform, the output waveform of a multilevel inverter alternates in ...[Details]
The 2025 China International Automotive Testing Exhibition will be held at the Shanghai World Expo Exhibition and Convention Center from August 27 to 29, 2025.
Clacton Seafront, UK, ...[Details]
In the field of intelligent driving, regulations are becoming increasingly stringent, and the technical threshold continues to rise. Especially after the traffic accident in March 2025, the Ministr...[Details]
In daily life, when we purchase a transformer, we are faced with the installation and wiring procedures. Generally speaking, large transformers such as power transformers are equipped with speciali...[Details]
Methods of DC motor speed regulation:
1. The voltage regulator can be used to change the input voltage and speed directly, which is often used for large kilowatt-level motors.
2. Thyristo...[Details]
Tools/Materials
Yitong Chuanglian MODBUS to PROFIBUS Gateway YT-PB-03
Siemens s7-300
This article describes how to configure the YT-PB-03 MODBUS to PROFIBUS gat...[Details]
Common methods for troubleshooting roller press bearing wear include repair welding, thermal spraying, brush plating, and scrapping and replacement. However, these methods are often subject to asse...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
