Above ratings are based on the thermal resistances using a multi-layer circuit board (EIA/JESD51). For mounting on a mono-layer board, power derating shall be
needed. Please inquire of us about conditions.
※1 素子毎の負荷電力の合計が、パッケージ定格電力を超えない条件で御½用ください。
※1 Total power consumption of all elements should not exceed the package power rating.
The resistor of this product is formed by narrow patterning a thin metal film. Thus, application of excessive voltage causes burn and destruction of the resistive film, abnormality
in resistance or open resistance and loss of proper function. The properly and electrostatically measured taping materials are used for the components, but attention should be paid
to the fact that there is some danger the parts may be destructed by static electricity(equivalent to 500V or over at 100pF, 1.5kΩ) to cause a change in resistance in the conditions
of an excessive dryness when mounting on the boards. Similarly, care should be given not to apply the excessive static electricity at the time of mounting on the boards. When
designing, consideration can be taken into withstanding ESD for customized KPC products. Please consult with us about the details.
●
Hand soldering by iron soldering or repairment are not recommended because KPC is a multi-pin product.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling
strength. In the case of 5〜35℃/35〜75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas
like hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability.
There is a problem with the comparator of MSP430G2453 in the application: when the P1.0 port is used as the positive input port of the analog comparator, the external input signal on this IO port disa...
This is what I did before. I bought one myself, and then I applied for another one and won it. But now I have two different boards I applied for. I feel like I have to put this Pico board aside, so I ...
Hello everyone: How can I add the program written in EVC that uses adodc3.0 to access the SQLCE database to the CE system image? I have added the dynamic libraries used by adodc and SQLCE to the syste...
[i=s]This post was last edited by chenzhufly on 2014-11-4 11:25[/i] [size=4][color=#0000ff]As the title says: This section talks about the power supply of SoC FPGA. By learning from this video, you ca...
Grounding of monitoring system and grounding of lightning protection Is there any contradiction between grounding of monitoring system and grounding of lightning protection? Yes!!! Some lightning prot...
Calibrators are widely used in university experiments. Among them, there are two experiments in nuclear physics experiments in modern physics experiments (GM counter and β absorption) that require ...[Details]
Although improper medical device product design is not always associated with medical device-related errors. Studies of users have shown that lack of adequate training accounts for 70% to 90% of suc...[Details]
The radio frequency identification (RFID) market is experiencing strong growth, with sales reaching $1.7 billion in 2004 and expected to reach $5.9 billion in 2008. This surge in demand is driven b...[Details]
1 Introduction
The integration of sensor technology and RFID has just started. As one of the world's major manufacturing and consumer countries, China should seize this opportunit...[Details]
How can we get the highest performance from an A/D converter? The obvious answer is to use good design and board layout, but there are other techniques that can be used to improve performance. We can ...[Details]
For more than 10 years, analog-to-digital converters (ADCs) have been widely used in industrial process control, medical instruments, communication systems, radar and other products as a booster of in...[Details]
PCI (Perip heral Component Interconnect) is an advanced high-performance 32/64-bit local bus that supports linear burst transmission and has a maximum data transmission rate of 132MB/s. At the same...[Details]
In response to a series of problems caused by the backwardness of traditional water meters, the Ministry of Construction of China has proposed the requirement of "three meters per household" for ur...[Details]
Lithium-ion battery is a widely used rechargeable battery. It has the advantages of high single-cell operating voltage, small size, light weight, high energy density, long cycle life, rapid full ch...[Details]
0 Introduction to the direct method of feedback linearization based on dynamic equilibrium state theory
The basic idea of the direct method of feedback linearization based on dynamic equilib...[Details]
Third generation (3G) mobile phones offer a variety of features with more functionality. As consumers enjoy the latest and better features of these communication devices, they continue to demand lo...[Details]
As mobile phones have evolved from simple voice communication tools to multimedia devices that integrate communication, imaging, and gaming, application processors are replacing baseband chips as t...[Details]
Compared with traditional light sources, light-emitting diodes (LEDs) have many advantages, such as low operating voltage, high energy efficiency, small size and directional light. They can provide...[Details]
introduction
The most common flight state of a fixed-wing aircraft is horizontal flight. If it is allowed to fly at a large angle, the action cannot be maintained all the time. If it is al...[Details]
E6601A is Agilent's new generation of comprehensive tester platform, designed to provide low-cost calibration solutions for mobile phone manufacturers. It uses an open Windows® XP platform, allowi...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
