Standard termination finish is 100% matte Tin (Sn).
Electrical Specifications
C0G (NP0)
Typical Capacitance Change vs. Temperature
15%
10%
5%
0%
-5%
-10%
-15%
-55˚C
-25˚C
0˚C
25˚C
50˚C
75˚C
100˚C
125˚C
Operating Temperature Range:
-55°C to +125°C
Temperature Coefficient:
0 ±30PPM/°C
Temperature Voltage Coefficient:
0 ±30PPM/°C
Insulation Resistance:
>100 Ω-F or 10 GΩ, whichever is less at 25°C, WDCV.
(The IR at 125°C is 10% of the value at 25°C)
Withstanding Voltage:
See below
Capacitance Tolerance:
C, D, F, G, J, K
Dielectric Strength is equal to 1.5 times rated voltage (WVDC) for 500 volt capacitors and 1.2 times (WVDC) for 1,000 through 5,000 volt capacitors.
Circuit applications in excess of 1,000 volts may require a surface coating to prevent external arcing.
24
Email:
sales@venkel.com
|
Phone:
512.794.0081
|
Toll Free:
800.950.8365
|
Web:
www.venkel.com
Rev. 05/2014-D
High Voltage Ceramic Capacitors
(HVC Series)
Electrical Specifications
X7R
Typical Capacitance Change vs. Temperature
15%
10%
5%
0%
-5%
-10%
-15%
-55˚C
-25˚C
0˚C
25˚C
50˚C
75˚C
100˚C
125˚C
Operating Temperature Range:
-55°C to +125°C
Temperature Coefficient:
0 ±15%∆°C MAX.
Temperature Voltage Coefficient:
X7R not applicable
Insulation Resistance:
>100 ohms F or 10 G ohms, whichever
is less at 25°C, WDCV.
(The IR at 125°C is 10% of the value at 25°C)
Withstanding Voltage:
See below
D.F. Specification:
≥50V, ≤2.5%
Capacitance Tolerance:
J,K,M,N
Test Parameters
Test parameters for Multilayer Ceramic Capacitors - X7R:
Test parameters for Multilayer Ceramic Capacitors - C0G (NP0):
1KHz ± 50Hz at 1.0 ± 0.2 Vrms, 25°C
1MHz ± 50KHz at 1.0 ± 0.2 Vrms ≤ 1000pF, 25°C
1KHz ± 50Hz at 1.0 ± 0.2 Vrms > 1000pF, 25°C
Note:
To ensure proper capacitance readings, the voltage level must be held constant. The HP4284 and Agilent E4980 has a "ALC" (Automatic Level Control) function
and should be switched to the "ON" position for accurate capacitance readings.
Additional values may be available. Please contact us for more information. Due to demand and raw material fluctuations, specific values may not be available.
Additional values may be available. Please contact us for more information. Due to demand and raw material fluctuations, specific values may not be available.
Additional values may be available. Please contact us for more information. Due to demand and raw material fluctuations, specific values may not be available.
I am working on reading and writing TF cards, using MSP430F5342. When I send CMD0, CMD55, and ACMD41, the return values are correct; but when I send CMD8, the V1.x card returns 0xFF, and the V2.0 card...
Last week, our progress was not good enough. It was mainly my fault. I will be defending my graduation thesis soon and I am busy with the typesetting of the thesis. I will send you the progress today....
Hello, EEWORLD forum friends:From now on - June 5, posts published between 23:30-07:00 will be subject to review. Please wait patiently for the posts to be published.From now on - June 5th, the blog s...
I set the baud rate to 9600, 19200, and 28800 and it works fine. Why doesn't it work when I set it to 57600? PCON |= 0x80; // 0x80=SMOD: set serial baudrate doubler TMOD |= 0x20; // put timer 1 into M...
In early 2002, I started to write a working program for an IC card prepaid electricity meter. The meter used Philips' 8-bit 51-expanded single-chip microcomputer
87LPC764
, and wa...[Details]
This article discusses how to wake up a touch-sensitive device such as a tablet without touching the device, using basic gesture recognition and novel proximity sensors. The article discusses the p...[Details]
In recent years, the market for mobile/portable devices such as smartphones and laptops has continued to grow rapidly. While these products continue to integrate more new features to enhance the ...[Details]
1. Introduction
Light control circuit plays a vital role in urban street lamps or corridor lighting. With light control circuit, the lights can be automatically turned on and off according to ...[Details]
As cellular phones become more advanced, the power consumption of the system during operation and the power consumption during standby are also increasing. Therefore, the power management design of...[Details]
In recent years, lighting has become an important area that countries around the world are targeting to promote energy conservation and environmental protection. According to statistics, about 20% ...[Details]
1 Introduction
As an emerging microfabrication technology, micro-electromechanical system (MEMS) technology has begun to be applied in various fields. It can integrate functions such as inform...[Details]
We know that microcontroller development tools generally include real-time online emulators and programmers. Among them, online emulators are very good tools, but they are also more expensive...[Details]
Flooded Batteries
This battery developed in Germany can be used to power flashlights, strobe lights and toys as long as it is filled with water. This battery can be stored for 50 years and can...[Details]
Introduction
Liquid crystal, as a display device, is widely used in low-power products such as instruments, meters, and electronic equipment with its unique advantages. In the past, the displ...[Details]
Abstract: The output of high-range acceleration sensor is less than 10 mV under the excitation of small signal. The noise of traditional test system may cover such small voltage signal, so that hig...[Details]
1 Introduction
With the rapid economic development, my country's electricity demand has been growing at a rate of more than 20% per year. According to the current economic development trend an...[Details]
Among the uses of electrical energy, lighting accounts for a considerable proportion. Compared with the earlier ordinary incandescent lamps, the fluorescent lamps and energy-saving lamps we commonl...[Details]
Movpower is a portable power bank. It can charge most mobile phones and digital products, such as digital cameras, PDAs, and mobile phones such as Apple, iPod, Blackberry, Motorola, Samsung, Nokia,...[Details]
Leakage current is generated by parasitic resistance paths between the measurement circuit and a nearby voltage source. This current can significantly reduce the accuracy of low current measurement...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
