EEWORLDEEWORLDEEWORLD

Part Number

Search

SK350M22BPSW1320

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 350V, 20% +Tol, 20% -Tol, 22uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size61KB,3 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance
Download Datasheet Parametric View All

SK350M22BPSW1320 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 350V, 20% +Tol, 20% -Tol, 22uF, Through Hole Mount, ROHS COMPLIANT

SK350M22BPSW1320 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance22 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
leakage current0.179 mA
Manufacturer's serial numberSG
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingBULK
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)350 V
ripple current160 mA
surface mountNO
Delta tangent0.2
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
SG
[ Electronic Ballast ]
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40 ~ +105°C / -25 ~ +105°C
Working Voltage : 160 ~ 400V / 450V
Rate Capacitance Range : 4.7 ~ 330µF / 3.3~100µF
Capacitance Tolerance : -20 ~ +20%
DC Leakage Current (µA) : I = 0.02 CV + 25
( After 2 Minute Application of DC Working Voltage at 25°C )
Dissipation Factor : at 120 Hz, 25°C
WV (V) : 160
200
250
350
400
450
D.F (%) : 15
15
15
20
24
24
For capacitor whose capacitance exceeds 1000µF. The value of D.F(%) is increased by 2% for every
addition of 1000µF.
Load Life : 5000 Hours at Assured with Full Rated Maximum Ripple Current Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : Hours, No Voltage Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200 % of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
Miniature Size Aluminum
Electrolytic Capacitors
Multiplier for Ripple Current
Frequency (Hz)
6.3~100V Below~68µF
50,60
0.80
120
1.00
300
1.20
1K 10K~100K
1.40
1.6
Temperature(°C)
Factor
65
1.70
85
1.40
105
1.00
DIAGRAM OF DIMENSIONS
4.0
5.0
6.3
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F
1.5
2.0
2.5
3.5
5.0
0.5
0.5
Rubber Stand-off
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
Dimensions : mm
Rubber End Seal
F 0.5
F 0.5
0.6
L
0.4Max.
15Min.
5Min.
D 0.5
L
15Min.
5Min.
D 0.5
7.5
10.0
0.8
0.8
Lantern with capacitive touch support
Use a vinyl cutter or laser cutter to make the enclosure, then use a Circuit Playground Bluefruit Express and Adafruit's NeoPixel ring to light up the lantern. You can add custom color animations and ...
dcexpert MicroPython Open Source section
1602 Interference Problem
The debugging is normal in the 51 development board, but in the board I made, 1602 sometimes has garbled characters and sometimes works normally. I don't know where the interference is. Does anyone kn...
ajieanyyn 51mcu
Please come in and help me, seniors
[i=s]This post was last edited by paulhyde on 2014-9-15 09:42[/i] AME8801AEEV330 This is a 3.3V output, it was normal before, but now the output becomes 2.6V. I don't know why? But as long as I touch ...
AME8801 Electronics Design Contest
TI's active equalization solution
As EV/HEV becomes more and more popular in the Chinese market, BMS, as its key part, has attracted more and more attention. TI has been studying this direction for many years and provides fully integr...
qwqwqw2088 Analogue and Mixed Signal
There is an error between the microcontroller and the ADC0809 digital-to-analog conversion! Attached pictures and program
I used ADC0809 connected to AT89S52! The voltage and output are wrong!! Provide the schematic diagram and program!! Please help me!! Thank you!! I have been busy all day and night. [[i] This post was ...
fefefe MCU
HP DL380 G6 server problem
We have a HP DL380 G6 server in our computer room: dual E5530cpu, 4 2gddr3 memory, 6 300g sas hard disks, dual power supplies. The standard configuration of this server is single E5530cpu, 3 2g memory...
skingshere Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1737  964  2475  153  2826  35  20  50  4  57 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号