Requires branch circuit backup with a UL LISTED Type K5 or RK5 fuse rated 15A minimum and no more than 4 times full load amps not to exceed 125A for 50 Amp or less
rating and not to exceed 175 for 51 through 100 Amp rating
Configuration Max. Frequency Phase Load Purpose With Without With Without With Without
Rating
Amps
Amps
1
Backup Backup Backup Backup Backup Backup
Fuse
Fuse
Fuse
Fuse
Fuse
Fuse
---
0.10 - 70
---
---
7,500
---
5,000 5,000 1,500
80
DC
---
71 - 100 71 - 100
---
10,000
---
5,000
---
5,000
125
DC
---
1 - 50
---
---
5,000
---
---
---
5,000
DC
---
0.10 - 50
---
---
---
5,000
0.10 - 70
3,000 1,500 3,000 1,500
Series
250
1
---
---
5,000
50 / 60
0.10 - 100
---
---
5,000 5,000
3
0.10 - 90
---
---
3,000 1,500
415
50 / 60
3
0.10 - 30
---
5,000
2
---
3,000 1,500
5,000 2,500
80
DC
---
7,500
---
5,000
Dual Coil
0.10 - 30
---
---
1,500
1,500
250
50 / 60
1&3
5,000 3,000
3,000
80
DC
---
0.10 - 70
---
---
7,500
---
5,000 5,000 1,500
250
50 / 60
1 & 3 0.10 - 70
---
---
5,000 3,000 1,500 3,000 1,500
Shunt
3,000 1,500
415
50 / 60
3
0.10 - 30
---
5,000
2
---
3,000 1,500
5,000 2,500
Voltage
Current Rating
Application
Codes
UL / CSA
TC1,2,OL1,U1
TC1,2,OL0,U1
TC1,2,OL1,U1
TC1,2,OL1,U1
---
Agency F, H, J or R
Agency J or R
2P, Agency J or R
---
Agency J or R
Construction Notes
TC1,2,OL1,C1
TC1,2,OL1,U1
TC1,2,OL1,U1
TC1,2,OL1,U1
TC1,2,OL1,C1
Rocker
Handle, Agency F, H, J or R
---
---
---
Rocker
Handle, Agency F, H, J or R
Notes:
1.
General Purpose ratings for UL/CSA only.
2.
Requires branch circuit backup with a UL LISTED Type K5 or RK5 fuse rated 15A minimum and no more than 4 times full load amps not to exceed 125A for 50 Amp or less
rating and not to exceed 175 for 51 through 100 Amp rating.
Table D:
Lists UL Listed (489), CSA Certified (C22.2 No. 5.1-M) configuration and performance capabilities as a Molded Case
I need to write an IE browser. How can I detect whether the current network status (should be the status of IE) is connected or disconnected? I have found through experiments that it does not work by ...
The backslash '\' in the post -simulation signal name, the post-simulation generates sdf files and .v files, add testbench, and simulate. Many signals have \ in front of them, such as wire \data , etc...
I am using an AT89S52 chip. After burning the following program, it cannot exit once it enters an interrupt. What is going on? It is OK that it cannot exit, but the light is still flashing. I hope you...
I just got a call from Shunfeng, saying there’s a courier. I was so excited... I knew it was 8962 from eeworld. I immediately ran to the school gate. It’s very cold in Chengdu this year. I was sweatin...
First of all, I would like to thank the Electronic Engineering World Forum for giving me this review opportunity. After receiving this kit, I thought it was sent by mistake at first glance. It seems t...
TIOBE's February 2012 programming language rankings have been released. This month, C# has squeezed into the top three, occupying the third place, while C++ has dropped to fourth place.Visual Basic wa...
Calibrators are widely used in university experiments. Among them, there are two experiments in nuclear physics experiments in modern physics experiments (GM counter and β absorption) that require ...[Details]
Although improper medical device product design is not always associated with medical device-related errors. Studies of users have shown that lack of adequate training accounts for 70% to 90% of suc...[Details]
introduction
At the beginning of this century, Veit used Einthoven's galvanometer to record the electrical activity of the human pregnant uterus from the body surface for the first time. In 19...[Details]
For more than 10 years, analog-to-digital converters (ADCs) have been widely used in industrial process control, medical instruments, communication systems, radar and other products as a booster of in...[Details]
Engineers who are new to wireless design and wireless product development need to master the basics of
RF measurement
. In many cases, this process is to enable engineers who have been engag...[Details]
0 Introduction
Metal halide lamp (MHL) as a green lighting source has been widely used in the field of indoor and outdoor lighting. However, when using this green lighting source, the matc...[Details]
0 Introduction
At present, the analysis of intra-pulse signals in pulse radar has always been a hot topic and difficulty in research. How to measure the intra-pulse carrier frequency more ...[Details]
Lithium-ion batteries have a high energy-to-weight and energy-to-volume ratio, no memory effect, can be recharged many times, have a long service life, and are becoming increasingly cheaper. A good...[Details]
Semiconductor devices used in high-end computing (advanced microprocessors) and consumer electronics (graphics and gaming chipsets) devices generally provide data rates up to 6.4Gbps through hig...[Details]
Power Integrations (PI) has introduced three charger/adapter reference designs using its new LinkSwitch-II series of AC-DC switching power conversion ICs. The new LinkSwitch-II devices use high-pre...[Details]
A correct circuit design cannot be manufactured 100% correctly when it is taken to the factory for manufacturing. It will always be affected by various uncertainties, such as deviations in manufact...[Details]
Abstract:
An amplifier solution for ceramic speaker systems is presented.
Keywords:
audio; ceramic speaker; amplifier; Class G
Today's portable devices require smaller, thinne...[Details]
Battery system architecture
For many years, nickel-cadmium batteries and later nickel-metal hydride battery technology have dominated the market. Lithium batteries have only entered ...[Details]
Touch sensors have been in widespread use for many years, but recent advances in mixed-signal programmable devices have made capacitive touch sensors a practical, value-added alternative to mechani...[Details]
Abstract:
Aiming at the problems of repeated design and high cost of existing LED large-screen displays, a modular LED large-screen display is proposed, which can realize flexible configurati...[Details]