EEWORLDEEWORLDEEWORLD

Part Number

Search

SN006M0220A3F31012

Description
Aluminum Electrolytic Capacitor, Non-polarized, Aluminum (wet), 6.3V, 20% +Tol, 20% -Tol, 220uF, Through Hole Mount, RADIAL LEADED
CategoryPassive components    capacitor   
File Size189KB,4 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance
Download Datasheet Parametric View All

SN006M0220A3F31012 Overview

Aluminum Electrolytic Capacitor, Non-polarized, Aluminum (wet), 6.3V, 20% +Tol, 20% -Tol, 220uF, Through Hole Mount, RADIAL LEADED

SN006M0220A3F31012 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance220 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
leakage current0.04458 mA
Manufacturer's serial numberSN
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingTAPE
polarityNON-POLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)6.3 V
ripple current235 mA
surface mountNO
Delta tangent0.24
Terminal shapeWIRE
YAGEO CORPORATION
ELECTROLYTIC CAPACITORS
Miniature Aluminum
Electrolytic Capacitors
SN
[ For Non-Polar ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors For
Non-Polar General Purpose
ELECTRICAL CHARACTERISTICS
Operating Temperature Range : -40 ~ +105°C / -25 ~ +105°C
Rated Voltage Range : 6.3 ~ 100V / 160 ~ 250V
Rated Capacitance Range : 0.22 ~ 2200µF / 0.47 ~ 100µF
Capacitance Tolerance : -20 ~ +20% at 120Hz, 20°C
DESCRIPTION
Non-polar for used in reversing polarity DC voltage
circuits.
MULTIPLIER FOR RIPPLE CURRENT
Frequency Coefficient
FREQUENCY (Hz)
FACTOR
Temperature Coefficient
TEMPERATURE (°C)
FACTOR
65
1.30
85
1.20
105
1.00
60
120 300 1K
10K
0.75 1.00 1.20 1.32 1.65
DC Leakage Current (µA) : I = 0.03 CV + 3µA
(After Rated Voltage Applied for 2 Minutes)
Dissipation Factor
W V (V) : 6.3
10
16
25
35
50
63 ~ 100
160 ~ 250
D.F. (%) : 24
20
17
15
14
12
10
20
For capacitors whose capacitance exceeds 1000µF. The value of D.F is increased by 2% for every
addition of 1000µF.
Endurance : 1000 Hours at 105°C with the Polarity Inverted Every 250 Hours
(a) Capacitance Change : Within 25% of Initial Value
(b) Dissipation Factor : Not Exceeding 200% of Specified Value
(c) Leakage Current : Not Exceeding the Specified Value
Shelf Life : After having been placed at 105°C without voltage applied for 500 hours, the capacitors
shall meet the same requirements as Endurance.
DIAGRAM OF DIMENSIONS
Rubber Stand-off
Dimensions: mm
4.0
5.0
Rubber End Seal
F
1.5
2.0
2.5
3.5
5.0
0.45
0.5
0.6
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
F
±
0.5
6.3
8.0
F
±
0.5
10.0
12.0
13.0
16.0
18.0
22.0
L
15Min.
5Min.
D
±
0.5
L
15Min.
5Min.
D
±
0.5
L
16 L + 1.5Max.
L
>
16 L + 2Max.
Dø = 8 & 10 L + 2.5Max.
<
20 Dø + 0.5
20 Dø + 1
7.5
10.0
0.8
Looking for remote control software
I am looking for remote control software that can display and operate WINCE system machines on the PC side. Please give me some advice....
kumelon Embedded System
Need C language for AT89C2051
I need to implement a solution: AT89C2051 circuit has been set up, now the software 3, 6, 7, 8 pins selective level input, when 3 pin input 2 low level 2 pin output drive 8050 three-pole tube, when 6 ...
windows_01 51mcu
How to use MOSFET (the easiest to understand material)
How to use MOSFET (the easiest to understand information)[size=4][b][/b][/size]...
Jacktang Analogue and Mixed Signal
In the end, what is the purpose of work?
Originally, this seemed to be a question that did not need to be answered. I knew from childhood that I had to study hard, strive to get into a good university, and then find a job to support myself a...
向农 Talking about work
Could you please tell me what board this is?
Could you please tell me what board this is? Thanks!...
zhl2402 Microchip MCU
instrumentation amplifier
[i=s]This post was last edited by dontium on 2015-1-23 13:31[/i] The input from S1 is a sine wave, why does the output from S2 look a bit like a square wave? Thanks....
jnicm Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1604  487  1434  2155  598  33  10  29  44  13 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号