EEWORLDEEWORLDEEWORLD

Part Number

Search

SK200M0220A7FM2235

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 200V, 20% +Tol, 20% -Tol, 220uF, Through Hole Mount, RADIAL LEADED, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size66KB,4 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance
Download Datasheet Parametric View All

SK200M0220A7FM2235 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 200V, 20% +Tol, 20% -Tol, 220uF, Through Hole Mount, RADIAL LEADED, ROHS COMPLIANT

SK200M0220A7FM2235 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance220 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
leakage current1.76 mA
Manufacturer's serial numberSA
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingTR
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)200 V
ripple current312 mA
surface mountNO
Delta tangent0.2
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
Miniature Size Aluminum
Electrolytic Capacitors
SA
[ High Ripple Current and Long load life ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40° ~ +105°C
-25° ~ +105°C
Working Voltage : 6.3 ~ 100V 160 ~ 450V
Rate Capacitance Range : 0.1 ~ 22000µF
Capacitance Tolerance : -20 ~ +20%
DC Leakage Current (µA) : I
0.03 CV or 4(µA) after 1 minute , I
0.04 CV +40(µA) after 1 minute
( Measurements shall be Made After a 1 Minute Charge at Rated Working Voltage )
Dissipation Factor : at 120 Hz, 25°C
DESCRIPTION
High Temperature Load Life at 105°C for
3000~8000 Hours
WV (V) : 6.3 10 16 25 35 50 63 100 160 200 250 315 400 450
D.F (%) : 28 24 20 16 14 12 10
8
20 20 20 25 25 25
For capacitor whose capacitance exceeds 1000µF. The value of D.F(%) is increased by 2% for every
addition of 1000µF.
WV (V)
:
6.3
5
12
160
3
10
4
10
200
3
16
3
8
250
4
25
2
5
350
4
35
2
4
400
6
50
2
3
450
15
63
2
3
100
2
3
Impedance : Z - 25°C / Z + 20°C
Impedance : Z - 40°C / Z + 20°C
Freq.(Hz)
Rated voltage(V)
Cap(µF)
WV (V)
50
0.75
0.80
0.80
120
1.00
1.00
1.00
300
1.35
1.23
1.25
1K
1.57
1.34
1.40
10K-
2.00
1.50
1.60
:
Impedance : Z - 25°C / Z + 20°C
6.3~100V
-47
100~470
0.47~220
Load Life : At 105°C Assured with Full Rated Maximum Ripple Current Applied
ø5~ø6=3000 hours.
ø8~ø10=5000 hours.
>ø12=8000 hours.
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : 1000 Hours, No Voltage Applied, at 105°C
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200 % of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
Dimensions : mm
Rubber Stand-off
4.0
Rubber End Seal
160~450
Temperature(°C)
Factor
~55
2.23
60
2.17
70
2.00
85
1.75
105
1.00
DIAGRAM OF DIMENSIONS
F
1.5
2.0
2.5
3.5
5.0
0.45
0.5
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
5.0
6.0
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F 0.5
F 0.5
0.4Max.
15Min.
0.6
L
15Min.
5Min.
D 0.5
L
5Min.
D 0.5
7.5
10.0
0.8
0.8
Nengdian Electronics Capacitive Liquid Level Sensor D1CS-D54 Review
[i=s]This post was last edited by wo4fisher on 2021-9-12 10:55[/i]1. Test environment 5V2A mobile phone charger head, Torch multi-function DC tester, liquid container (measuring cylinder, beverage bot...
wo4fisher Sensor
Non-inverting Ratio Operational Amplifier
I made a board using the circuit shown in the picture, why is the output high voltage when the input signal is not turned on, and the output is correct after the input signal is turned on?...
hql724914 Analog electronics
Amplifier design techniques and amplifier processes summarized by ADI
[b]Clamp Amplifiers[/b] Clamp amplifiers allow the designer to specify high (VCH) and low (VCL) output clamp voltages to clamp the output signal at a specific level. Analog Devices’ unique CLAMPIN inp...
wstt Microcontroller MCU
Exchange development boards. There are a lot of development boards. People in Beijing can borrow from each other.
[size=14px]Requirement: [b]Urgent need for power detection equipment[/b][/size] [size=14px][b]Xiaomi TDS test lead USB power detector[/b][/size][color=#000][backcolor=inherit][font="][size=14px][color...
lidonglei1 Buy&Sell
Homemade simple hot air soldering station
Modern electronic products widely use surface welding technology, which brings inconvenience to maintenance personnel in disassembling components. In particular, disassembling multi-pin chips and plas...
songrisi DIY/Open Source Hardware
Discussion on multicast issues in Z-stack
When debugging the SampleApp example in the protocol stack of Z-stack 2007, I found that in the user event initialization function SampleApp_Init, both the coordinator and the terminal were added to g...
爱好汽车电子 RF/Wirelessly

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1367  1886  1231  2385  1073  28  38  25  49  22 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号