EEWORLDEEWORLDEEWORLD

Part Number

Search

3GW42A-150T-250.00

Description
LVCMOS Output Clock Oscillator, 250MHz Nom, ROHS AND REACH COMPLIANT, SMD, 4 PIN
CategoryPassive components    oscillator   
File Size128KB,1 Pages
ManufacturerEuroquartz
Websitehttp://www.euroquartz.co.uk/
Environmental Compliance
Download Datasheet Parametric View All

3GW42A-150T-250.00 Overview

LVCMOS Output Clock Oscillator, 250MHz Nom, ROHS AND REACH COMPLIANT, SMD, 4 PIN

3GW42A-150T-250.00 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerEuroquartz
package instructionROHS AND REACH COMPLIANT, SMD, 4 PIN
Reach Compliance Codecompliant
Maximum control voltage2.31 V
Minimum control voltage0.99 V
Frequency Adjustment - MechanicalNO
Frequency offset/pull rate150 ppm
frequency stability25%
linearity10%
Installation featuresSURFACE MOUNT
Nominal operating frequency250 MHz
Maximum operating temperature70 °C
Minimum operating temperature
Oscillator typeLVCMOS
Output load15 pF
physical size11.4mm x 9.6mm x 2.5mm
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Nominal supply voltage3.3 V
surface mountYES
maximum symmetry55/45 %
EURO
QUARTZ
LVCMOS SMD 11.4 x 9.6 x 2.5mm, 4 pad
Frequency range 200.1MHz to 800MHz
LVCMOS Output
Supply Voltage 3.3 VDC
High Q fundamental mode crystal
Low jitter multiplier circuit
DESCRIPTION
GW42 VCXOs, are packaged in an industry-standard, 4 pad, 11.4mm
x 9.6mm x 2.5mm SMD package. GW42 VCXOs incorporate a high Q
fundamental crystal and a low jitter multiplier circuit.
SPECIFICATION
Frequency Range:
Supply Voltage:
Output Logic:
Integrated Phase Jitter:
Period Jitter RMS:
Period Jitter Peak to peak:
Phase Noise:
Initial Frequency Accuracy:
Output Voltage HIGH (1):
Output Voltage LOW (0):
Pulling Range:
Temperature Stability:
Output Load:
Start-up Time:
Duty Cycle:
Rise/Fall Times:
Current Consumption
<96MHz:
>96MHz:
Linearity:
Modulation Bandwidth:
Input Impedance:
Slope Polarity:
(Transfer function)
OUTLINE & DIMENSIONS
GW42 VCXO
200.1MHz ~ 800.0MHz
200.1MHz to 800.0MHz
3.3 VDC ±5%
LVCMOS
2.6ps typical, 4.0ps maximum
(for 155.250MHz)
4.3ps typical (for 155.250MHz)
27.0ps typical (for 155.250MHz)
Tune to the nominal frequency
with Vc= 1.65 ±0.2VDC
90% Vdd minimum
10% Vdd maximum
From ±30ppm to ±150ppm
15pF
10ms maximum, 5ms typical
50% ±5% measured at 50% Vdd
1.2ns typical (15pF load)
30mA maximum (15pF load)
40mA maximum (15pF load)
10% maximum, 6% typical
25kHz minimum
2 MW minimum
Monotonic and Positive. (
Storage Temperature:
Ageing:
Enable/Disable (Tristate):
RoHS Status:
-50° to +100°C
±5ppm per year maximum
Not available (
Fully compliant
)
PHASE NOISE
10Hz
100Hz
1kHz
10kHz
100kHz
1MHz
10MHz
-65dBc/Hz
-95dBc/Hz
-120dBc/Hz
-125dBc/Hz
-121dBc/Hz
-120dBc/Hz
-140dBc/Hz
FREQUENCY STABILITY
Stability Code Stability ±ppm Temp. Range
A
25
0°~+70°C
B
50
0°~+70°C
C
100
0°~+70°C
D
25
-40°~+85°C
E
50
-40°~+85°C
F
100
-40°~+85°C
If non-standard frequency stability is required
Use ‘I’ followed by stability, i.e. I20 for ±20ppm
PART NUMBER SCHEDULE
Example:
3GW42B-80N-250.00
Supply Voltage
3 = +3.3V
Series Designator
GW42
Stability over temperature range
(
)
Pullability in ±ppm
Pullability determinator
N = minimum
M = maximum
T = Typical
Frequency in MHz
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 info@euroquartz.co.uk www.euroquartz.co.uk
Novice question: Can the firmware program in the integrated USB module part of arm9 be rewritten?
I am using the 6410 smartphone development board based on arm9. I want to modify the firmware of the USB module, which is actually to modify the value of the descriptor. Is there any expert who has do...
grace811226 ARM Technology
Mir MYC-YT507 development board review: Play NES games with the Famicom
Preface Previously, we used Qt to implement a ranger that fights tanks, but that was not enough. This time, we ported the NES emulator and turned the development board into a red and white game consol...
qinyunti Domestic Chip Exchange
11 Electronics Contest, please come in
[i=s] This post was last edited by paulhyde on 2014-9-15 09:07 [/i] For control applications, what modules should be prepared? What are the chips (preferably commonly used) and corresponding circuits ...
魔尊123 Electronics Design Contest
FPGA-related examples
:lol :lol :) :) A newcomer...
cernllyy FPGA/CPLD
Network labeling question
When I draw a schematic, why does it often report that the network number is not connected? PROTEL99SE....
thtlj PCB Design
"Keil Software - Cx51 Compiler User Manual Chinese Complete Version"
《Keil Software – Cx51 Compiler User Manual Chinese Complete Version》 The network is not good...
zuie 51mcu

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2657  1978  1927  2298  1557  54  40  39  47  32 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号