EEWORLDEEWORLDEEWORLD

Part Number

Search

SK160M33B3S11019

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 160V, 20% +Tol, 20% -Tol, 33uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size61KB,3 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance
Download Datasheet Parametric View All

SK160M33B3S11019 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 160V, 20% +Tol, 20% -Tol, 33uF, Through Hole Mount, ROHS COMPLIANT

SK160M33B3S11019 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance33 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
leakage current0.1306 mA
Manufacturer's serial numberSG
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingBULK
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)160 V
ripple current210 mA
surface mountNO
Delta tangent0.15
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
SG
[ Electronic Ballast ]
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40 ~ +105°C / -25 ~ +105°C
Working Voltage : 160 ~ 400V / 450V
Rate Capacitance Range : 4.7 ~ 330µF / 3.3~100µF
Capacitance Tolerance : -20 ~ +20%
DC Leakage Current (µA) : I = 0.02 CV + 25
( After 2 Minute Application of DC Working Voltage at 25°C )
Dissipation Factor : at 120 Hz, 25°C
WV (V) : 160
200
250
350
400
450
D.F (%) : 15
15
15
20
24
24
For capacitor whose capacitance exceeds 1000µF. The value of D.F(%) is increased by 2% for every
addition of 1000µF.
Load Life : 5000 Hours at Assured with Full Rated Maximum Ripple Current Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : Hours, No Voltage Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200 % of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
Miniature Size Aluminum
Electrolytic Capacitors
Multiplier for Ripple Current
Frequency (Hz)
6.3~100V Below~68µF
50,60
0.80
120
1.00
300
1.20
1K 10K~100K
1.40
1.6
Temperature(°C)
Factor
65
1.70
85
1.40
105
1.00
DIAGRAM OF DIMENSIONS
4.0
5.0
6.3
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F
1.5
2.0
2.5
3.5
5.0
0.5
0.5
Rubber Stand-off
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
Dimensions : mm
Rubber End Seal
F 0.5
F 0.5
0.6
L
0.4Max.
15Min.
5Min.
D 0.5
L
15Min.
5Min.
D 0.5
7.5
10.0
0.8
0.8
DSP tms320vc33 timer timing time?
EXTCLK is connected to 11.0592M crystal oscillator XIN is grounded CLKMD0 and CLKMD1 are both connected to high level. Timer0.Period = 0x1d4c0; Timer0.Counter = 0x1d4c0; Timer0.Control = 0x3f2; How lo...
webzming Embedded System
Help with low power consumption issues
I am now using msp430f169 to write programs.All functions are complete. Iam using LPM3 mode.When I power on and enter LPM3 mode, there is still 130ua current, which seems to be too high.I have disconn...
lyylsc Microcontroller MCU
Review Weekly Report 20221010: Sipeed GW2A FPGA development board and Renesas ultra-low power MCU RA2L1 are here~
Activities currently being applied for1. Sipeed GW2A FPGA development board ( newly launched ) After being evaluated and praised by engineers in our forum, the domestic Gaoyun FPGA is coming again. Th...
EEWORLD社区 Special Edition for Assessment Centres
2440 Reading the temperature chip always fails to trigger an interrupt. Is there any way to do this?
Calling the IIC folder through the application layer in the BSP package does not work properly, so I have to switch to the bootloader layer to do temperature detection, but the interrupt cannot be tri...
Franz The Industrial Cloud
msp430f169 ADC pin voltage
I use MSP430F169, the data from the ADC pin grounding test is also more than 2000, and there is indeed voltage on the AD pin, I don't know what's going on, help please!!!...
卡军方 Microcontroller MCU
I have a module called wavecom's wismo2c, but it can't connect to GPRS. How can I fix it so that I can access the Internet?
It is said that a software upgrade is needed. How can I do it? Please give me some advice. The information I checked said that this module did not support GPRS when it was first launched. If it is to ...
zhou.63624 Embedded System

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2703  2075  1693  460  683  55  42  35  10  14 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号