MK1A158M10020QL datasheet, PDF

Datasheet> All Categories > Passive components> capacitor> MK1A158M10020QL

MK1A158M10020QL: DescriptionAluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 10V, 20% +Tol, 20% -Tol, 1500uF,; CategoryPassive components capacitor; File Size129KB，3 Pages; ManufacturerSAMWHA; Websitehttp://www.samwha.com/

Download Datasheet Parametric View All

MK1A158M10020QL Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 10V, 20% +Tol, 20% -Tol, 1500uF,

MK1A158M10020QL Parametric

Parameter Name	Attribute value
Maker	SAMWHA
package instruction	,
Reach Compliance Code	compliant
capacitance	1500 µF
Capacitor type	ALUMINUM ELECTROLYTIC CAPACITOR
diameter	10 mm
dielectric materials	ALUMINUM (WET)
length	20 mm
Manufacturer's serial number	MK
negative tolerance	20%
Number of terminals	2
Maximum operating temperature	105 °C
Minimum operating temperature	-40 °C
Package form	Radial
method of packing	Box
polarity	POLARIZED
positive tolerance	20%
Rated (DC) voltage (URdc)	10 V
ripple current	1820 mA
series	MK
Terminal pitch	5 mm

Preview

Download Datasheet

View All

MINIATURE ALUMINUM ELECTROLYTIC CAPACITORS

High Ripple Current

Series

Low Impedance

Solvent Proof

Ripple current compared with LK series

Enabled high ripple current by a reduction of impedance at high frequency

High reliability withstanding 5000 hours load life at 105 C

(2000 ~ 3000 hours for smaller case sizes as specified below)

Complied to the RoHS directive

Item

Operating temperature range

Leakage current max.

Capacitance tolerance

-40 ~ +105 C

I = 0.01CV or 3

I = 0.03CV or 4

Characteristics

A whichever is greater (after 2 minutes)

A whichever is greater (after 1 minute)

20% at 120Hz, 20 C

Capacitance > 1000

F : tan

increases by 0.02 for each 1000

0.19

0.16

0.14

F from below value.

0.10

0.08

100

0.08

Dissipation factor max.

(at 120Hz, 20 C)

tan

6.3

0.22

0.12

Low temperature characteristics

(Impedance ratio at 120Hz)

Z-40 C / Z+20 C

Z-25 C / Z+20 C

After an application of DC bias voltage plus the rated AC ripple current for 5000 hours at 105 C.

The measurement shall meet the following limits. The DC voltage plus the peak AC voltage

combined must not exceed the rated voltage.

Leakage current

Load life

Capacitance change

tan

Life time

Less than specified value

Within

25% of the initial value

Less than 200% of the specified value

D = 5, 6.3

2000 hours

D = 8

3000 hours

5000 hours

are same as load life value.

Shelf life (at 105 C)

After 1000 hours no load test, leakage current, capacitance and tan

The measurement shall be performed at 20 C by the KS C 6035 clause 5.4.

DRAWING

Unit : mm

Insulating sleeve

0.05 Tinned copper-ply wire

0.5 max.

0.5

2.0

0.5

6.3

2.5

0.5

1.5

3.5

0.6

5.0

0.6

12.5

5.0

0.6

2.0

7.5

0.8

7.5

0.8

max.

15 min.

4 min.

Safety vent (

6.3 up)

FREQUENCY COEFFICIENT OF PERMISSIBLE RIPPLE CURRENT

Frequency

120Hz

0.40

0.50

0.55

0.60

0.70

1kHz

0.65

0.70

0.75

0.80

0.85

10kHz

0.82

0.84

0.86

0.88

0.90

50kHz

0.94

0.96

0.97

100kHz

1.00

~ 33

39 ~ 270

330 ~ 680

820 ~ 1800

2200 ~

116

Recommended Resources

A differential line driver circuit diagram

Transistor attenuated tone control circuit

Light ophthalmic light switch circuit (2)

Phone in use indicator light circuit

20/5t bridge crane electrical schematic circuit

810 computer motherboard circuit diagram_36

Keil error (reentrant usage): Source code: #include "httpd.h" #include "fs.h" #include #includestatic u8_t print_stats(u8_t next) reentrant; static u8_t file_stats(u8_t next); static u8_t tcp_stats(u8_t next) reentrant;cgifunction...; almax12 Embedded System

What will happen if the ePWM pull-up resistor is enabled?: In the TI piccolo manual, "For pins that can be used as ePWM outputs, the internal pull-up resistors are disabled by default." What are the consequences if the ePWM pull-up resistors are enabled? Than...; dxj Microcontroller MCU

N ways to play with an LED (Part 7) ---- Freertos (with documents, code, and video): N ways to play with an LED ( Part 7 )—FreeRtos Author: chenzhufly Email: chenzhufly@126.com 2010-05-08From the previous discussion, it seems that everyone has a special liking for the operating system...; chenzhufly NXP MCU

How can I get the ROM file required for POSE (Palm OS Emulator)?: RT...; avermei Embedded System

Engineers, don’t just work, you have to eat too.: Compare the pictures at the beginning: [/size][size=5]Current screenshots: [/size]...; dontium Talking

I applied for SEED M2802xV1.0 from TI but there is no schematic diagram. I am very depressed. Please give me the schematic diagram.: I participated in the TI competition. I applied for SEED M2802xV1.0 from TI. I don't have a schematic diagram. I'm depressed. I need a schematic diagram....; zhangyuechi Microcontroller MCU

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components