EEWORLDEEWORLDEEWORLD

Part Number

Search

FKP30.1/100/5PCM7.5

Description
Film Capacitor, Polypropylene, 100V, 0.1uF
CategoryPassive components    capacitor   
File Size305KB,1 Pages
ManufacturerWIMA
Websitehttps://www.wima.de/
Environmental Compliance
Download Datasheet Parametric View All

FKP30.1/100/5PCM7.5 Overview

Film Capacitor, Polypropylene, 100V, 0.1uF

FKP30.1/100/5PCM7.5 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerWIMA
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance0.1 µF
Capacitor typeFILM CAPACITOR
Custom functionsTape and Reelry
dielectric materialsPOLYPROPYLENE
JESD-609 codee3
Number of terminals2
Maximum operating temperature100 °C
Minimum operating temperature-55 °C
Package formRadial
Rated (AC) voltage (URac)63 V
Rated (DC) voltage (URdc)100 V
Terminal surfaceTin (Sn)
Terminal pitch7.5 mm
Questions about AD9361
When the AD9361 local oscillator is set to 2400M, assuming that a 2402M signal is collected at this time, then through [/font][/color][color=#4183c4][font=微软雅黑][url=http://bbs.elecfans.com/zhuti_fpga_...
dreamandactual Analog electronics
Chip dedicated heat sink
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 20:00[/i] MAP series high thermal conductivity soft silicone thermal insulation pads are widely used in electronic equipment industries su...
warxp990 Mobile and portable
I made a board and found it can't start using Jun Yixing's u-boot
I made a board and used Junyixing SD card burning method to burn uboot, kernel, and file system into nand flash. But after switching to nand flash to start, I found that uboot did not print any inform...
bailyzheng Embedded System
Does HAL_Init() require any other initialization work?
When generating an STM32 project with STM32CubeMX, I found that the port initialization work was not completed. ----------------------- The routines provided by ST are also like this:In HAL_Init(), no...
dontium stm32/stm8
After the development board is started, I can enter the general user but cannot enter the root. What should I do?
Question: My development board can start normally, but after startup it is $, not #. I entered an ordinary user panws, but don't know how to become the root user. The su and useradd commands cannot be...
问渠 Embedded System
【KW41z】The wireless alarm system test board has been soldered. I don't know how the debugging will go.
【KW41z】The wireless alarm system test board has been soldered. I wonder how the debugging will go:surrender:...
damiaa NXP MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2295  2472  2899  1674  132  47  50  59  34  3 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号