EEWORLDEEWORLDEEWORLD

Part Number

Search

SE-K160M2R20A2S-611

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 160V, 20% +Tol, 20% -Tol, 2.2uF, Through Hole Mount, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size60KB,3 Pages
ManufacturerYAGEO
Websitehttp://www.yageo.com/
Environmental Compliance
Download Datasheet Parametric View All

SE-K160M2R20A2S-611 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 160V, 20% +Tol, 20% -Tol, 2.2uF, Through Hole Mount, ROHS COMPLIANT

SE-K160M2R20A2S-611 Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
MakerYAGEO
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
capacitance2.2 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
dielectric materialsALUMINUM (WET)
leakage current0.01704 mA
Manufacturer's serial numberSE-K
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
Package shapeCYLINDRICAL PACKAGE
method of packingTR
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)160 V
ripple current15 mA
surface mountNO
Delta tangent0.15
Terminal shapeWIRE
YAGEO CORPORATION
ALUMINUM ELECTROLYTIC CAPACITORS
SE-K
[ For General ]
105°C Single-Ended Lead Aluminum Electrolytic Capacitors Rated Voltage up to 450V
Miniature Size Aluminum
Electrolytic Capacitors
ELECTRICAL CHARACTERISTICS
Operating Temperature : -40° ~ +105°C / -25° ~ +105°C
Working Voltage : 6.3 ~ 250V / 350 ~ 450V
Rate Capacitance Range : 0.47 ~ 15000µF / 0.47 ~ 150µF
Capacitance Tolerance : -20 ~ +20%
DC Leakage Current (µA) : I = 0.01CV + 3 / 0.03CV + 10
( After 2 Minutes Application of DC Working Voltage at 25°C )
Dissipation Factor : at 120 Hz, 25°C
W V (V) : 6.3
10
16
25
35
50
63
80
100 160 ~ 250 350 ~ 450
D.F (%) : 26
22
18
16
14
12
10
10
10
15
20
For capacitor whose capacitance excceds 1000 µF. The value of DF(%) is increased by 2% for every
addition of 1000 µF.
Load Life : 1000 Hours at Assured with Full Rated Maximum Ripple Current Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed the Initial Requirement
Shelf Life : 500 Hours, No Voltage Applied
(a) Capacitance Change : Within 20% of Initial Value
(b) Dissipation Factor : Not Exceed 200% of Initial Requirement
(c) Leakage Current : Not Exceed 200% of Initial Requirement
DESCRIPTION
Lower-cost capacitors expressly intended for high
density printed circuit board.
Ideally suited for general-purpose applications,
entertainment electronics.
Feature High CV Product with Moderate Cost
Multiplier for Ripple Current
Frequency (Hz)
6.3~100V Below~68µF
6.3~100V 100~680µF
6.3~110V 1000~22000µF
160~450V ALL Cap(µF)
120
1.00
1.00
1.00
1.00
300
1.20
1.10
1.05
1.05
1K 10K~100K
1.30
1.45
1.15
1.25
1.10
1.15
1.10
1.50
Temperature(°C)
Factor
65
1.80
85
1.40
105
1.00
DIAGRAM OF DIMENSIONS
4.0
5.0
6.0
8.0
10.0
12.0
13.0
16.0
18.0
22.0
F
1.5
2.0
2.5
3.5
5.0
0.45
0.5
Rubber Stand-off
Vinyl Sleeve
(P.V.C)
Rubber End Seal
Vinyl Sleeve
(P.V.C)
Dimensions : mm
Rubber End Seal
F 0.5
F 0.5
0.6
L
0.4Max.
15Min.
5Min.
D 0.5
L
15Min.
5Min.
D 0.5
7.5
10.0
0.8
0.8
The original BBC micro:bit sponsored by Taiwanese netizen ImHor
Today I received the original BBC micro:bit sponsored by Taiwanese netizen ImHor, which gave me more confidence in the next hardware design.[url=https://bbs.eeworld.com.cn/thread-507607-1-1.html][size...
dcexpert MicroPython Open Source section
Design of wireless network sensor based on Bluetooth protocol
Abstract: Based on the sensor interface standard IEEE1451.2, this paper introduces some specific technical points for the realization of wireless networked sensors, proposes a wireless networked senso...
ohahaha RF/Wirelessly
One atmel51 development board, one Lingyang61 development board, and replace the idle embedded development board
I have an idle atmel51 development board and a Lingyang 61 development board. Since I am using a laptop now, these two development boards do not have the function of USB downloading programs. I want t...
fengkb Buy&Sell
How do I set port A and how do I set the bit selection?
I would like to ask: AN0 and AN1 of port A are used as analog ports, and the other three ports are used as digital output ports, which are used as bit selections for the digital tube display of the mi...
rsszd Microchip MCU
stm8l152c6 Two 595 drive digital tube display abnormal
/* STM8L-discovery uses the official library of 595 to drive LED (common anode digital tube) test 2014.07.09 masonson */ #include "stm8l15x.h" /* #define RCK GPIOE->ODR | 0X20 //595 12 RCK latch #defi...
masonson stm32/stm8
【Low Power】Xilinx Tools and IP Updates
Xilinx strives to help designers improve their work efficiency and continuously improves its products, IP and design tools.Xilinx has developed an application called Documentation Navigator that allow...
hangsky FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1258  2591  369  1373  1850  26  53  8  28  38 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号