Operating Temperature Range ......................... -40°C to +125°C
Junction Temperature .....................................................+150°C
Storage Temperature Range ............................ -65°C to +150°C
Lead Temperature (soldering, 10s) ................................. +300°C
Soldering Temperature (reflow) .......................................+260°C
Absolute Maximum Ratings
SUP, SUPSW, LX, EN to PGND ...........................-0.3V to +42V
SUP to SUPSW ....................................................-0.3V to +0.3V
BIAS to AGND .........................................................-0.3V to +6V
SPS, FOSC, COMP to AGND ................-0.3V to (V
BIAS
+ 0.3V)
FSYNC, PGOOD, FB to AGND ..............-0.3V to (V
BIAS
+ 0.3V)
OUT to PGND .......................................................-0.3V to +12V
BST to LX ................................................................-0.3V to +6V
AGND to PGND....................................................-0.3V to +0.3V
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Package Thermal Characteristics
(Note 1)
TQFN
Junction-to-Ambient Thermal Resistance (θ
JA
) ..........30°C/W
Junction-to-Case Thermal Resistance (θ
JC
) .................2°C/W
Note 1:
Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer
board. For detailed information on package thermal considerations, refer to
www.maximintegrated.com/thermal-tutorial.
Electrical Characteristics
PARAMETER
Supply Voltage
Load-Dump Event Supply
Voltage
Supply Current
Supply Current (5V)
Shutdown Supply Current
BIAS Regulator Voltage
BIAS Undervoltage Lockout
BIAS Undervoltage-Lockout
Hysteresis
Thermal-Shutdown Threshold
Thermal-Shutdown Threshold
Hysteresis
OUTPUT VOLTAGE
PWM-Mode Output Voltage
(Note 2)
Skip-Mode Output Voltage
(Note 3)
PWM-Mode Output Voltage
(Note 2)
V
SUP
= V
SUPSW
= 14V, V
EN
= 14V, L1 = 2.2µH, C
IN
= 4.7µF, C
OUT
= 44µF, C
BIAS
= 2.2µF, C
BST
= 0.1µF, R
FOSC
= 12kΩ, T
A
= T
J
=
-40°C to +125°C, unless otherwise noted. Typical values are at T
A
= +25°C.
SYMBOL
V
SUP
,
V
SUPSW
V
SUP_LD
STANDBY
STANDBY
CONDITIONS
MIN
3.5
TYP
MAX
36
42
UNITS
V
V
µA
µA
µA
V
V
mV
°C
°C
t
LD
< 1s
Standby mode, no load, V
OUT
= 3.3V,
V
FSYNC
= 0V
Standby mode, no load, V
OUT
= 5V,
V
FSYNC
= 0V
V
E
N = 0V
V
SUP
= V
SUPSW
= 6V to 42V. I
BIA
S = 0
to 10mA
V
BIAS
rising
4.7
2.9
15
20
5
5
3.15
400
175
15
I
SUP_
I
SUP_
30
35
10
5.4
3.4
500
I
SHDN
V
BIAS
V
UVBIAS
V
OUT_5V
SKIP_5V
V
FB
= V
BIAS
, 6V < V
SUPSW
< 36V,
fixed-frequency mode
No load, V
FB
= V
BIAS
, skip mode
V
F
B = V
BIA
S, 6V < V
SUPS
W < 36V,
fixed-frequency mode
4.9
4.9
3.23
5
5
3.3
5.1
5.15
3.37
V
V
V
V
OUT_
V
OUT_3.3V
www.maximintegrated.com
Maxim Integrated │ 3
MAX20002/MAX20003
36V, 220kHz to 2.2MHz, 2A/3A Fully
Integrated Step-Down Converters
with 15μA Operating Current
Electrical Characteristics (continued)
PARAMETER
Skip-Mode Output Voltage
(Note 3)
Load Regulation
Line Regulation
BST Input Current
I
BST_ON
I
BST_OFF
LX Current Limit
LX Rise Time
Spread Spectrum
High-Side Switch On-
Resistance
High-Side Switch Leakage
Current
Low-Side Switch On-
Resistance
Low-Side Switch Leakage
Current
FB Input Current
FB Regulation Voltage
FB Line Regulation
Transconductance (from FB to
COMP)
Minimum On-Time
Maximum Duty Cycle
Oscillator Frequency
SYNC, EN, AND SPS LOGIC THRESHOLDS
External Input Clock Acquisition
time
External Input Clock Frequency
External Input Clock High
Threshold
External Input Clock Low
Threshold
FSYNC Leakage Current
Soft-Start Time
t
SS
t
FSYN
C
I
FB
V
FB
∆V
LINE
gm
t
ON_MIN
DC
MAX
R
ON_L
R
ON_H
I
LX
SYMBOL
V
OUT_
SKIP_3.3V
V
SUP
= V
SUPSW
= 14V, VEN = 14V, L1 = 2.2µH, C
IN
= 4.7µF, C
OUT
= 44µF, C
BIAS
= 2.2µF, C
BST
= 0.1µF, R
FOSC
= 12kΩ, T
A
= T
J
=
-40°C to +125°C, unless otherwise noted. Typical values are at T
A
= +25°C.
CONDITIONS
No load, V
FB
= V
BIAS
, skip mode
V
FB
= V
BIAS
, 30mA < I
LOA
D < 3A
V
FB
= V
BIAS
, 6V < V
SUPSW
< 36V
High-side MOSFET on,
V
BST
- V
LX
= 5V
High-side MOSFET off,
V
BST
- V
LX
= 5V
MAX20003
MAX20002
V
OUT
= 5V, 3.3V
Spread spectrum enabled
I
LX
= 0.5A, V
BIA
S = 5V
High-side MOSFET off, V
SU
P = 36V,
V
LX
= 0V, T
A
= +25°C
I
LX
= 0.5A, V
BIA
S = 5V
Low-side MOSFET off, V
SUP
= 36V,
V
LX
= 36V, T
A
= +25°C
T
A
= +25°C
FB connected to an external resistive
divider, 6V < V
SUPSW
< 36V
6V < V
SUPSW
< 36V
V
FB
= 1V, V
BIAS
= 5V
0.99
3.75
2.5
MIN
3.23
TYP
3.3
0.5
0.02
1.5
1.5
5
3.33
4
FOSC
±3%
60
1
35
1
20
1
0.02
700
80
98
R
FOSC
= 73.2kΩ
R
FOSC
= 12kΩ
2.0
400
2.2
2.4
99
140
5
70
5
100
1.01
mΩ
µA
mΩ
µA
nA
V
%/V
µS
ns
%
kHz
MHz
6.25
4.16
MAX
3.4
UNITS
V
%
%/V
mA
µA
A
ns
1
R
FOSC
= 12kΩ (Note 4)
1.8
1.4
0.4
1
5.6
8
12
2.6
Cycle
MHz
V
V
µA
ms
V
FSYNC_HI
V
FSYN
C rising
V
FSYNC_LO
V
FSYN
C falling
T
A
= +25°C
www.maximintegrated.com
Maxim Integrated │ 4
MAX20002/MAX20003
36V, 220kHz to 2.2MHz, 2A/3A Fully
Integrated Step-Down Converters
with 15μA Operating Current
Electrical Characteristics (continued)
PARAMETER
Enable Input High Threshold
Enable Input Low Threshold
Enable Threshold-Voltage
Hysteresis
Enable Input Current
Spread-Spectrum Input High
Threshold
Spread-Spectrum Input Low
Threshold
Spread-Spectrum Input Current
SYMBOL
V
EN_HI
V
EN_LO
V
EN_HYS
I
EN
V
SPS_HI
V
SPS_LO
I
SPS
V
RISING
V
FALLING
V
SUP
= V
SUPSW
= 14V, V
EN
= 14V, L1 = 2.2µH, C
IN
= 4.7µF, C
OUT
= 44µF, C
BIAS
= 2.2µF, C
BST
= 0.1µF, R
FOSC
= 12kΩ, T
A
= T
J
=
-40°C to +125°C, unless otherwise noted. Typical values are at T
A
= +25°C.
CONDITIONS
MIN
2.4
0.6
0.2
T
A
= +25°C
2.0
0.4
T
A
= +25°C
V
FB
rising, V
PGOOD
= high
V
FB
falling, V
PGOOD
= low
I
SINK
= 5mA
V
OUT
in regulation, T
A
= +25°C
V
OUT
rising (Monitor FB pin)
V
OUT
falling (Monitor FB pin)
107
104
93
90
0.1
95
92.5
25
0.4
1
1
97
95
0.1
1
TYP
MAX
UNITS
V
V
V
µA
V
V
µA
POWER-GOOD AND OVERVOLTAGE-PROTECTION THRESOLDS
PGOOD Switching Level
PGOOD Debounce Time
PGOOD Output Low Voltage
PGOOD Leakage Current
Overvoltage Protection
Threshold
%V
FB
µs
V
µA
%
Note 2:
Device not in dropout condition.
Note 3:
Guaranteed by design; not production tested.
Note 4:
Contact the factory for SYNC frequency outside the specified range.
Dear friends, does anyone have a cracked version of PLC programming and simulation software that supports Windows 7 64-bit? I would be very grateful. Urgent. . . [email]994527322@qq.com[/email]...
The operating voltage of this chip is 2.2-3.6V. There is a problem in my circuit design. The current output voltage is 3.7V. Has anyone used this chip? In this case, will it not work properly if the g...
I am a 2009 undergraduate graduate, majoring in electronic information engineering. I am determined to enter the embedded development industry, but unfortunately I have not found a suitable job. I wou...
I need a microcontroller with USB function and DLL library to facilitate labview calling. The current C8051F320 has weak performance and cannot meet the needs. Please recommend a microcontroller....
I am a beginner in single-chip microcomputers. I used to work in computer software, but I am not very familiar with hardware. Now I want to switch to single-chip microcomputer programming and developm...
The rapid development of the Internet has realized high-speed information transmission and resource sharing, greatly facilitating people's lives. Embedded systems are widely used in various electr...[Details]
introduction
1 The significance of using RTOS on MSP430
It is understandable that it is meaningless to use RTOS on MSP430. Because the hardware resources of MSP430 are limited (for exampl...[Details]
introduction
Solar cells and LED lighting are typical applications of new energy and energy-saving and efficient technologies. Solar LED lighting uses solar cells to convert solar energy...[Details]
Aromatic gases are widely present in food, medicine, cosmetics and various daily chemical products, such as snacks, liquor, spices, Chinese herbal medicines, plasters, perfumes, soaps, shampoos, et...[Details]
With concerns about the growing energy crisis, motor efficiency has become an important and timely topic. This is because motors use 63% to 70% of the electricity produced in the United States and ...[Details]
Abstract: Aiming at the needs of coal-rock acoustic emission signal monitoring system, a data acquisition circuit with 24-bit resolution and 16-channel synchronous data acquisition function is desi...[Details]
Temperature compensated quartz crystal oscillator (TCXO) is widely used as a high-precision frequency source in communication systems, radar navigation systems, precision measurement and control sy...[Details]
a. Keep the battery clean, wipe off the spilled electrolyte, contaminated dirt and dust in time; keep the poles and terminal clamps clean and in good contact, and apply vaseline or butter to preven...[Details]
The most important components of new energy electric vehicles are power batteries, electric motors and energy conversion control systems. The power battery must achieve high performance such as fas...[Details]
Measurement compatibility
It is very important to ensure the compatibility between the pressure sensor and its actual application. Before making a pressure sensor selection, the fo...[Details]
Stepper motors have been widely used in automatic or semi-automatic equipment such as CNC machine tools, medical equipment, and instruments. The usual way to control stepper motors with computers i...[Details]
During the global semiconductor industry recession, the automotive electronics market has performed strongly, especially the application of car remote control systems has become more and more wides...[Details]
1 Features
1.1 Single cell operating voltage up to 3.7V
It is three times that of nickel-cadmium batteries and nickel-metal hydride batteries, and nearly twice that of lead-acid batteries...[Details]
High specific energy lithium/thionyl chloride (Li/SOCl2) batteries are widely used in multi-functional intelligent meters (such as smart meters, water meters, etc.) as real-time clocks and memory b...[Details]
Cloud computing is a network-based computing method. In this way, shared hardware and software resources and information can be provided to computers and other devices on demand. Cloud computing is th...[Details]
TI Technology Forum
京公网安备 11010802033920号
EEWORLD
