EEWORLDEEWORLDEEWORLD

Part Number

Search

372100100

Description
Thumb/Pushwheel Switch, 7 Switches, Binary Coded Decimal, 10 Positions, 0.1A, 28VDC, Solder Terminal, Panel Mount, ROHS COMPLIANT
CategoryMechanical and electronic products    switch   
File Size668KB,8 Pages
ManufacturerITT
Websitehttp://www.ittcannon.com/
Environmental Compliance
Download Datasheet Parametric View All

372100100 Overview

Thumb/Pushwheel Switch, 7 Switches, Binary Coded Decimal, 10 Positions, 0.1A, 28VDC, Solder Terminal, Panel Mount, ROHS COMPLIANT

372100100 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerITT
package instructionROHS COMPLIANT
Reach Compliance Codecompliant
ECCN codeEAR99
body width28.96 mm
body height33.02 mm
Body length or diameter66.52 mm
Contact (AC) maximum rated R load.1A@120VAC
Maximum contact current (AC)0.1 A
Maximum contact current (DC)0.1 A
Contact (DC) maximum rated R load.1A@28VDC
Maximum contact voltage (AC)120 V
Maximum contact voltage (DC)28 V
Electrical life100000 Cycle(s)
Installation featuresPANEL MOUNT
Number of positions10
Number of switching segments7
Maximum operating temperature65 °C
Minimum operating temperature-10 °C
surface mountNO
switch functionBINARY CODED DECIMAL
Switch typeTHUMB/PUSHWHEEL SWITCH
Termination typeSOLDER
C&K 3 Series
Thumbwheel Switches
Features/Benefits
Most complete product offering in the industry
Spacers available to fit most panel cutouts
Front or rear mounting options
Typical Applications
Test & measurement equipment
Industrial equipment
Computer devices
Specifications
CONTACT RATING:
CARRY: 1 AMP continuous.
SWITCH: 100 mA max.
OPERATING VOLTAGE: 50 mV to 28 V DC or 120 V AC.
ELECTRICAL LIFE: 100,000 actuations.
CONTACT RESISTANCE: Below 100 m
typ. initial @
2-4 V DC, 100 mA.
INSULATION RESISTANCE: 109
min.
DIELECTRIC STRENGTH: 500 Vrms min. @ sea level
between common terminal and any output.
OPERATING TEMPERATURE: -10ºC to 65ºC.
Materials
HOUSING: ABS plastic.
THUMBWHEEL: ABS plastic.
ROTOR CONTACTS: Precious metal on copper alloy.
STATOR CONTACTS: Hard gold over nickel over copper
on epoxy fiberglass.
NOTE:
Specifications and materials listed above are for switches with standard options
For information on specific and custom switches, consult Customer Service Center.
* Note: All models listed are RoHS compliant. See Technical Data section of this catalog for
RoHS compliant and compatible definitions and specifications.
Build-A-Switch
To order, simply select desired option from each category and place in the appropriate box. Available options are shown and
described on pages N–9 thru N–12. For additional options not shown in catalog, consult Customer Service Center.
Consult factory for illumination availability.
Thumbwheel & Pushwheel
Series
3
Thumbwheel switch
Number of Sections
0
Switch section
1
1 Switch section
2
2 Switch sections
3
3 Switch sections
4
4 Switch sections
5
5 Switch sections
6
6 Switch sections
7
7 Switch sections
8
8 Switch sections
9
More than 8
switch sections
Function Code
11
Decimal, SP, 10 position
14
Resistor decade
21
BCD, 10 position
23
Complement of BCD, 10 position
27
BCD, 10 position
31
BCD, 10 position
71
BCH, 16 position
Mounting Style
00
Snap-in, front mount
09
Snap-in, front mount*
10
Rear mount
Terminations
19
Rear mount*
0
Type 0
20
Rear mount
1
Type 1, extended type 0
29
Rear mount*
N
Solder pins with .100” spacing**
P
Solder pins with .156” spacing**
9
Any combination
Color/Marking/Stops
0
Matte black body, gloss
black wheel,
white marking
N
*X9 mounting styles must be ordered with ‘0’ number of sections.
** Note: Termination option N (RoHS compliant) replaced termination option 3 (Non-RoHS compliant).
Termination option P (RoHS compliant) replaced termination option B (Non-RoHS compliant).
Seal
0
No seal
1
Sealed contacts
2
Dust lens
3
Sealed contacts & dust lens
Dimensions are shown: Inch (mm)
Specifications and dimensions subject to change
N–8
www.ittcannon.com
Configuration and use of TMS320F28379D SCID SCIB
TI's official routines only give the configuration of SCIA and not the configuration methods of other SCIs. In fact, the configurations of these are the same. The following takes the configuration of ...
灞波儿奔 DSP and ARM Processors
Analog electronics learning
I cut the analog electronics e-book into pictures to make it easier for masters to read.As shown in the attached Figure 6.7.5, 1. Why is the figure a current feedback operational amplifier circuit? Wh...
whwshiyuan1984 Analog electronics
How to design inverter upper arm drive
I would like to ask you, if the inverter upper bridge arm drive requires a charge pump circuit, how should it be designed? Thank you...
huimin Power technology
Problems in making wireless mobile phone chargers
I need a set of production drawings of a wireless charger urgently. . . . . . . . . . ....
范凡 RF/Wirelessly
40 Practical Knowledge Summary of Analog Circuits
1 In electrical interface design, reflection attenuation usually deteriorates at high frequencies because lossy transmission line reflections are frequency-dependent. In this case, it is extremely imp...
lhx694845003 Energy Infrastructure?
Wince application software development to obtain the unique identification code of the device
How can I get the unique identification code of a device in Windows CE system? I found that I can use KernalIoControl to get the device ID and Name on msdn (http://msdn.microsoft.com/zh-cn/library/ms1...
lingr Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 925  2390  810  899  1389  19  49  17  28  55 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号