The input/output pins are placed in a high impedance state when
the device is deselected (En HIGH), the outputs are disabled (G
HIGH), or during a write operation (En LOW and Wn LOW).
E
1
A(18:0)
G
512K x 8
W
1
EL
O
E
0
DQ(7:0)
- SEL Immune >80 MeV-cm
2
/mg
- LET
TH
(0.25) = >10 MeV-cm
2
/mg
- Saturated Cross Section cm
2
per bit, 5.0E-9
- <1E-8 errors/bit-day, Adams 90% geosynchronous
heavy ion
Writing to each memory is accomplished by taking one of the
chip enable (En) inputs LOW and write enable (Wn) inputs
LOW. Data on the I/O pins is then written into the location
specified on the address pins (A
0
through A
18
). Reading from
the device is accomplished by taking one ofthe chip enable (En)
and output enable (G) LOW while forcing write enable (Wn)
HIGH. Under these conditions, the contents of the memory
location specified by the address pins will appear on the I/O pins.
Only one SRAM can be read or written at a time.
512K x 8
Figure 1. UT8Q1024K8 SRAM Block Diagram
1
PM
EN
W
0
FEATURES
q
25ns maximum (3.3 volt supply) address access time
q
Dual cavity package contains two (2) 512K x 8 industry-
standard asynchronous SRAMs; the control architecture
allows operation as an 8-bit data width
q
TTL compatible inputs and output levels, three-state
bidirectional data bus
q
Typical radiation performance
- Total dose: 50krad(Si)
INTRODUCTION
The QCOTS
TM
UT8Q1024K8 Quantified Commercial Off-the-
Shelf product is a high-performance 1M byte (8Mbit) CMOS
static RAM built with two individual 524,288 x 8 bit SRAMs
with a common output enable. Memory access and control is
provided by an active LOW chip enable (En), an active LOW
output enable (G). This device has a power-down feature that
reduces power consumption by more than 90% when deselected.
T
DEVICE OPERATION
NC
NC
A0
A1
A2
A3
A4
E1
DQ0
DQ1
V
DD
V
S S
DQ2
DQ3
W1
A5
A6
A7
A8
A9
W2
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
NC
E2
NC
A18
A17
A16
A15
G
DQ7
DQ6
V
SS
V
DD
DQ5
DQ4
A14
A13
A12
A11
A10
NC
NC
NC
Table 1. Device Operation Truth Table
G
X
1
X
1
0
Wn
X
0
1
1
EL
O
0
0
0
Figure 2. 25ns SRAM Pinout (44)
A(18:0)
DQ(7:0)
En
Wn
G
V
DD
V
SS
Address
Data Input/Output
Device Enable
WriteEnable
Output Enable
Power
IN
D
Ground
Notes:
1. To avoid bus contention, on the DQ(7:0) bus, only one En can be driven low
simultaneously while G is low.
EV
PIN NAMES
Notes:
1. “X” is defined as a “don’t care” condition.
2. Device active; outputs disabled.
READ CYCLE
A combination of Wn greater than V
IH
(min) with En and G less
than V
IL
(max) defines a read cycle. Read access time is
measured from the latter of device enable, output enable, or valid
address to valid data output.
SRAM Read Cycle 1, the Address Access is initiated by a change
in address inputs while the chip is enabled with G asserted and
Wn deasserted. Valid data appears on data outputs DQ(7:0) after
the specified t
AVQV
is satisfied. Outputs remain active
throughout the entire cycle. As long as device enable and output
enable are active, the address inputs may change at a rate equal
to the minimum read cycle time (t
AVAV
).
SRAM Read Cycle 2, the Chip Enable-controlled Access is
initiated by En going active while G remains asserted, Wn
remains deasserted, and the addresses remain stable for the
entire cycle. After the specified t
ETQV
is satisfied, the eight-bit
word addressed by A(18:0) is accessed and appears at the data
outputs DQ(7:0).
SRAM Read Cycle 3, the Output Enable-controlled Access is
initiated by G going active while En is asserted, Wn is
deasserted, and the addresses are stable. Read access time is
t
GLQV
unless t
AVQV
or t
ETQV
have not been satisfied.
2
PM
EN
En
1
I/O Mode
Mode
3-state
Standby
Write
Read
2
Read
Data in
3-state
Data out
Each die in the UT8Q1024K8 has three control inputs called
Enable (En), Write Enable (Wn), and Output Enable (G); 19
address inputs, A(18:0); and eight bidirectional data lines,
DQ(7:0). The device enable (En) controls device selection,
active, and standby modes. Asserting En enables the device,
causes I
DD
to rise to its active value, and decodes the 19 address
inputs to each memory die . Wn controls read and write
operations. During a read cycle, G must be asserted to enable
the outputs.
T
WRITE CYCLE
A combination of Wn less than V
IL
(max) and En less than
V
IL
(max) defines a write cycle. The state of G is a “don’t care”
for a write cycle. The outputs are placed in the high-impedance
state when eitherG is greater than V
IH
(min), or when Wn is less
than V
IL
(max).
Write Cycle 1, the Write Enable-controlled Access is defined
by a write terminated by Wn going high, with En still active.
The write pulse width is defined by t
WLWH
when the write is
initiated byWn, and by t
ETWH
when the write is initiated by En.
Unless the outputs have been previously placed in the high-
impedance state byG, the user must wait t
WLQZ
before applying
data to the eight bidirectional pins DQ(7:0) to avoid bus
contention.
Write Cycle 2, the Chip Enable-controlled Access is defined by
a write terminated by the former of En or Wn going inactive.
The write pulse width is defined by t
WLEF
when the write is
initiated by Wn, and by t
ETEF
when the write is initiated by the
En going active. For the Wn initiated write, unless the outputs
have been previously placed in the high-impedance state by G,
the user must wait t
WLQZ
before applying data to the eight
bidirectional pins DQ(7:0) to avoid bus contention.
TYPICAL RADIATION HARDNESS
The UT8Q1024K8 SRAM incorporates features which allow
operation in a limited radiation environment.
Table 2. Typical Radiation Hardness
Design Specifications
1
Total Dose
Heavy Ion
Error Rate
2
50
<1E-8
krad(Si) nominal
Errors/Bit-Day
Notes:
1. The SRAM will not latchup during radiation exposure under recommended
operating conditions.
2. 90% worst case particle environment, Geosynchronous orbit, 100 mils of
Aluminum.
IN
D
EV
EL
O
3
PM
EN
T
ABSOLUTE MAXIMUM RATINGS
1
(Referenced to V
SS
)
SYMBOL
V
DD
V
I/O
T
STG
P
D
T
J
Θ
JC
I
I
PARAMETER
DC supply voltage
Voltage on any pin
Storage temperature
Maximum power dissipation
Maximum junction temperature
2
Thermal resistance, junction-to-case
3
DC input current
LIMITS
-0.5 to 4.6V
-0.5 to 4.6V
-65 to +150°C
1.0W (per byte)
+150°C
10°C/W
±
10 mA
RECOMMENDED OPERATING CONDITIONS
SYMBOL
V
DD
T
C
V
IN
PARAMETER
Positive supply voltage
Case temperature range
DC input voltage
IN
D
EV
EL
O
4
PM
EN
T
Notes:
1. Stresses outside the listed absolute maximum ratings may cause permanent damage to the device. This is a stress rating only, and functional operation of the device
at these or any other conditions beyond limits indicated in the operational sections of this specification is not recommended. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability and performance.
2. Maximum junction temperature may be increased to +175
°C
during burn-in and steady-static life.
3. Test per MIL-STD-883, Method 1012.
LIMITS
3.0 to 3.6V
-40 to +125°C
0V to V
DD
DC ELECTRICAL CHARACTERISTICS (Pre/Post-Radiation)*
(-40°C to +125°C) (V
DD
= 3.3V + 0.3)
SYMBOL
V
IH
V
IL
V
OL1
V
OL2
V
OH1
V
OH2
C
IN 1
C
IO 1
I
IN
I
OZ
PARAMETER
High-level input voltage
Low-level input voltage
Low-level output voltage
Low-level output voltage
High-level output voltage
High-level output voltage
Input capacitance
Bidirectional I/O capacitance
Input leakage current
Three-state output leakage current
(CMOS)
(CMOS)
I
OL
= 8mA, V
DD
=3.0V
I
OL
= 200µA,V
DD
=3.0V
I
OH
= -4mA,V
DD
=3.0V
I
OH
= -200µA,V
DD
=3.0V
ƒ
= 1MHz @ 0V
ƒ
= 1MHz @ 0V
V
SS
< V
IN
< V
DD,
V
DD
= V
DD
(max)
0V < V
O
< V
DD
V
DD
= V
DD
(max)
G = V
DD
(max)
I
OS 2, 3
I
DD
(OP)
Short-circuit output current
Supply current operating
@ 1MHz
-2
-2
2.4
V
DD
-0.10
10
12
2
2
CONDITION
MIN
2.0
0.8
0.4
0.08
MAX
UNIT
V
V
V
V
V
V
pF
pF
µA
µA
0V < V
O
< V
DD
PM
EN
-40°C and 25°C
+125°C
5
T
-90
90
125
mA
mA
180
mA
6
mA
mA
40
Inputs: V
IL
= 0.8V,
V
IH
= 2.0V
I
OUT
= 0mA
V
DD
= V
DD
(max)
I
DD1
(OP)
Supply current operating
@40MHz
I
DD2
(SB)
Nominal standby supply current
@0MHz
D
IN
Notes:
* Post-radiation performance guaranteed at 25°C per MIL-STD-883 Method 101 9 .
1. Measured only for initial qualification and after process or design changes that could affect input/output capacitance.
2. Supplied as a design limit but not guaranteed or tested.
3. Not more than one output may be shorted at a time for maximum duration of one second.
I am making a three-phase brushless DC motor drive module. The driver chip is MC33035. Now I am wondering why the N-channel MOS tubes of the lower bridge arm are all turned on (Vgs=13.8v) when I test ...
This is actually using the duty cycle of PWM to control the brightness of the LED. It is a very common function for microcontrollers, but it is even more unimaginably simple under mbed. Before looking...
I am testing the trigger interrupt of P2_0 port, and the configuration is as follows: void Exti_Init(void) {EA = ENABLE; ///Open the general interruptP2IEN |= 0X01; ///Open P2 interruptIEN2 = 1; //???...
[align=left][color=#191919]Recently I’ve noticed that there are MMs hanging in many places...[/color][/align][align=left][color=rgb(25, 25, 25)]Some are lightly made up...[/color][/align][align=left][...
I started using ESP from 8266, and jumped directly from Anxinke's Eclipse development to Arduino. At that time, I heard that Lua could also be used for development. Although I later purchased NodeMCU,...
[size=4] There are three main types of processors that I have come into contact with, general-purpose microprocessors (MPUs), digital signal processors (DSPs), and SPARC platforms (short for Scalable ...
1. Equipment Overview
Shell-and-tube heat exchangers are a common heat exchange device used in chemical evaporation and heating equipment. Currently, the tubesheets of shell-and-tube heat exch...[Details]
With the rapid development of technology, automotive intelligence is increasing at an unprecedented rate. This not only enhances vehicle functionality and comfort, but also places higher deman...[Details]
We are entering a new era where people are increasingly affordably equipped with more electronic gadgets. Electronics have become essential to our lives. For example, the average consumer now owns ...[Details]
Since its invention in the mid-1940s, the microwave oven has evolved from a humble beginning to commercial use, entering homes in the 1960s and rapidly gaining popularity. Its basic functionality a...[Details]
1. Multi-channel DAC technology bottleneck
Currently,
the development of multi-channel DAC technology focuses on two core challenges.
First, industrial applications urgently ...[Details]
With growing environmental awareness, the continuous improvement of three-electric technology and the increasing deployment of infrastructure such as charging stations, the electrification of new e...[Details]
introduction
With the development and widespread use of integrated circuits in power electronics design, electronic products are trending towards smaller sizes, more components, and greater fu...[Details]
Recently, I received a request to use OK1028A-C to output PWM square wave. However, I found that there was no relevant instructions on the OK1028 platform, so I started writing this article.
A...[Details]
On August 19, Huawei's Executive Director and Chairman of the Device BG, Richard Yu, shared a Weibo post about a conversation he had with a Zunjie S800 owner. The owner had driven over 5,000 kilome...[Details]
As systems become increasingly used in industrial environments, industry safety requirements, as well as national and international safety regulations, need to be constantly updated to ensure a saf...[Details]
Overview of the BOM of Jetson Platform Core Components
As the industry's leading edge computing and data center platform, the NVIDIA Jetson series' powerful performance is powered by a careful...[Details]
On August 14, Chinese researchers broke through the bottleneck of energy density and application performance of existing traditional lithium-ion batteries and developed soft-pack batteries with an ...[Details]
Many automakers use 0-60 mph acceleration as a selling point for electric vehicles. It's the most direct indicator of a vehicle's power. This 0-60 mph acceleration is crucial for electric vehicles,...[Details]
Q: What does it mean when a Cisco router says your connection has been redirected by the remote host? What is the difference between a WAN adapter and an AC97 Data Fax Modem? Are they the same conn...[Details]
If you have these bad driving habits, they can affect the life of electric vehicle batteries. If you change these bad driving habits, you can extend the life of electric vehicle batteries:
① F...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
