T212C126J050CSC datasheet, PDF

Datasheet> All Categories > Passive components> capacitor> T212C126J050CSC

T212C126J050CSC: DescriptionTantalum Capacitor, Polarized, Tantalum (dry/solid), 50V, 5% +Tol, 5% -Tol, 12uF, Through Hole Mount, AXIAL LEADED; CategoryPassive components capacitor; File Size157KB，14 Pages; ManufacturerKEMET; Websitehttp://www.kemet.com

Download Datasheet Parametric View All

T212C126J050CSC Overview

Tantalum Capacitor, Polarized, Tantalum (dry/solid), 50V, 5% +Tol, 5% -Tol, 12uF, Through Hole Mount, AXIAL LEADED

T212C126J050CSC Parametric

Parameter Name	Attribute value
Is it lead-free?	Contains lead
Is it Rohs certified?	incompatible
Maker	KEMET
package instruction	,
Reach Compliance Code	compliant
ECCN code	EAR99
capacitance	12 µF
Capacitor type	TANTALUM CAPACITOR
dielectric materials	TANTALUM (DRY/SOLID)
JESD-609 code	e0
leakage current	0.003 mA
Manufacturer's serial number	T212
Installation features	THROUGH HOLE MOUNT
negative tolerance	5%
Number of terminals	2
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package shape	TUBULAR PACKAGE
method of packing	AMMO PACK
polarity	POLARIZED
positive tolerance	5%
Rated (DC) voltage (URdc)	50 V
surface mount	NO
Delta tangent	0.04
Terminal surface	Tin/Lead (Sn/Pb)
Terminal shape	WIRE

Preview

Download Datasheet

View All

TANTALUM HERMETICALLY SEALED / AXIAL — MIL-PRF-39003

T110 SERIES — POLAR TYPE, T212 (CSR13)

KEMET standard hermetic sealed T110 Series are desirable for use in high humidi-

ty environments. They are ruggedly built, designed for miniaturized circuitry, and are

especially suited for coupling, bypass, filtering and R-C timing circuits. They exhibit

excellent stability, extremely low DC leakage current, dissipation factor, and

ESR/impedance over a wide temperature and frequency range.

Available in standard EIA capacitance values from .0047-330 µF in ±20%, ±10%, and ±5%

tolerances and working voltages from 6-125 VDC.

Higher CV values in comparable case sizes are available in KEMET T140 Series.

Refer to page 27.

Included in the following Series table is a complete listing of CSR13 qualified MIL-

PRF-39003 capacitors. KEMET is approved to manufacture the S (0.001%/k hrs.)

Exponential & D (0.001%/k hrs.) Graded failure rate levels.

KEMET is now offering low ESR limits in the T110 Series. See ESR chart on page

19. You may order the lower ESR by using Customer Specification 2864 as the last

four digits of the part number.

Effective September 30, 2005, the KEMET T110 Series is RoHS Compliant.

CAPACITOR OUTLINE DRAWINGS

1.50±.250

(38.10±6.35)

1.50±.250

(38.10±6.35)

UNINSULATED

CASE

SIZE

±0.005

±(.13)

±0.031

±(.79)

±0.010

±(.25)

INSULATED

±0.031

±(.79)

±0.002

±(.05)

MAX.

DIMENSIONS — INCHES & (MILLIMETERS)

0.125

(3.18)

0.175

(4.45)

0.279

(7.09)

0.341

(8.66)

0.250

(6.35)

0.438

(11.13)

0.650

(16.51)

0.750

(19.05)

0.135

(3.43)

0.185

(4.70)

0.289

(7.34)

0.351

(8.92)

0.286

(7.26)

0.474

(12.04)

0.686

(17.42)

0.786

(19.96)

0.020

(.51)

0.020

(.51)

0.025

(.64)

0.025

(.64)

0.422

(10.72)

0.610

(15.49)

0.822

(20.88)

0.922

(23.42)

TANTALUM

SERIES

T110, T212 (CSR13)

T111, T213 (CSR91)

T140, T242 (CSR23)

ORDERING INFORMATION*

XXX A 105 K 050 A S

SPECIFICATION

All capacitors are sleeved

unless specified.

CASE SIZE

A/B/C/D

PICOFARAD CODE

First two digits represent significant figures.

Third digit specifies number of zeros to follow.

LEAD MATERIAL

S — Standard

T – 100% Tin (T110, T140 Series only)

CAPACITANCE TOLERANCE

M — ±20%

K — ±10%

J — ±5%

FAILURE RATE**

GRADED

A — Not Applicable

B — 0.1%/k hrs.

C — 0.01%/k hrs.

D — 0.001%/k hrs.

EXPONENTIAL

M — 1%/k hrs.

P — 0.1%/k hrs.

R — 0.01%/k hrs.

S — 0.001%/k hrs.

VOLTAGE

At 85°C

**Part Number Example: T110A105K050AS (14 digits - no spaces)

*For Military Ordering Information, see page 4.

**Failure Rates apply only to military products.

MARKING INFORMATION

Marking: Unless otherwise specified by special order, standard marking of T110 Series capacitor consists of the following:

A, B, C & D CASES

+K 10%

R56 µF

100V

0312

Polarity, Manufacturer’s Identification and Capacitance Tol.

Nominal Capacitance — (µF) (“R” indicates decimal)

Voltage

Date Code (e.g.: 0312)

* For Military Marking, see page 4.

KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606 (864) 963-6300

Recommended Resources

Interface circuit between power supply coupler and relay

Push-pull single transformer inverter

Smoke detector circuit diagram A

Thyristor phase failure protection circuit

555 automatic timing controller circuit

Computer motherboard circuit diagram 815 2_23

DSP C6748 has slow calculation speed: I made a motor control + modulation program for DSP C6748+FPGA, and found that the calculation speed of 6748 is slow, and the program execution may not be completed (I used 28335 before and it was fin...; Fisher1612 DSP and ARM Processors

Why is it that the interrupt service routine is not allowed to have a return value? Please give me some advice, thank you.: I have seen many questions that ask you to find errors in an interrupt service program with a return value. The answer is: Interrupt service programs are not allowed to have return values. Interrupt s...; neckfully Embedded System

After voltage stabilization, it will heat up after working for a long time: I made a 220v 5v stabilizer, using a 12v transformer and then connected to a 78M05 to stabilize it to 5v, but after a long time, the transformer will get hot, and then the power will not be enough. It...; askahaha Embedded System

(Help) Question about capacitor selection?: As shown in the figure, what is the specific function of the capacitor marked in red? This figure is a mic circuit in an IP phone. How to determine its capacitance?...; kingyb Discrete Device

TI group-purchased chip DIY - Part 1: ADS8332: [i=s]This post was last edited by dontium on 2015-1-23 13:02[/i]I bought the chip from a group purchase, and I was itching to make one. Later, I printed a PCB. For details, see: bbs.eeworld../thread-3...; dontium Analogue and Mixed Signal

The high level output of Mega8 IO port is about 1.5V, and the low level output is about 0.3V. Please discuss it together.: [i=s] This post was last edited by huanjun123 on 2014-11-6 15:19 [/i] I made a minimum system based on mega8. When testing, the IO port high-level output was about 1.5V and the low-level output was ab...; huanjun123 Microchip MCU

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components