DS1035
3-in-1 High–Speed Silicon Delay Line
www.dalsemi.com
FEATURES
All-silicon timing circuit
Three independent buffered delays
Stable and precise over temperature and
voltage
Leading and trailing edge precision preserves
the input symmetry
Standard 8-pin DIP and 8-pin SOIC (150 mil)
Vapor phasing, IR and wave solderable
Available in Tape and Reel
PIN ASSIGNMENT
IN1
IN2
IN3
GND
1
2
3
4
8
7
6
5
V
CC
OUT1
OUT2
OUT3
DS1035M 8-Pin DIP
See Mech. Drawings Section
IN1
IN2
IN3
GND
1
2
3
4
8
7
6
5
V
CC
OUT1
OUT2
OUT3
DS1035Z 8-Pin SOIC (150-mil)
See Mech. Drawings Section
PIN DESCRIPTION
IN1-IN3
OUT1-OUT3
NC
V
CC
GND
(Sub)
- Input Signals
- Output Signals
- No Connection
- +5 Volt Supply
- Ground
- Internal substrate
connection, do not make
any external connections
to these pins
DESCRIPTION
The DS1035 series is a low-power +5-volt high-speed version of the popular DS1013 and complements
the DS1033 +3.3 Volt version.
The DS1035 series of delay lines have three independent logic buffered delays in a single package. The
device is Dallas Semiconductor’s fastest 3-in-1 delay line. It is available in a standard 8-pin DIP and 150
Mil 8-pin Mini-SOIC.
The device features precise leading and trailing edge accuracies. It has the inherent reliability of an all-
silicon delay line solution. The DS1035’s initial tolerance is
±1.5
or
±2.0
ns with an additional tolerance
over temperature and voltage of
±1.0
ns or
±1.5
ns, depending on the delay value. Each output is capable
of driving up to 10 LS loads.
Standard delay values are indicated in Table 1. Customers may contact Dallas Semiconductor at (982)
371-4348 for further information.
1 of 6
111799
DS1035
LOGIC DIAGRAM
Figure 1
PART NUMBER DELAY TABLE (t
PLH
, t
PHL
)
Table 1
PART NUMBER
DS1035-60
DS1035-80
DS1035-10
DS1035-12
DS1035-15
DS1035-20
DS1035-25
DS1035-30
DELAY PER
OUTPUT (ns)
6/6/6
8/8/8
10/10/10
12/12/12
15/15/15
20/20/20
25/25/25
30/30/30
INITIAL TOLERANCE
±1.5
ns
±1.5
ns
±1.5
ns
±1.5
ns
±1.5
ns
±1.5
ns
±2.0
ns
±2.0 ns
TOLERANCE OVER
TEMPERATURE
AND VOLTAGE
±1.0
ns
±1.0
ns
±1.0
ns
±1.0
ns
±1.5
ns
±1.5
ns
±1.5
ns
±1.5
ns
NOTES:
1. Nominal conditions are +25°C and V
CC
=+5.0 volts.
2. Temperature range of 0°C to 70°C and voltage range of 4.75 volts to 5.25 volts.
3. Delay accuracy is for both leading and trailing edges.
2 of 6
DS1035
TEST SETUP DESCRIPTION
Figure 2 illustrates the hardware configuration used for measuring the timing parameters of the DS1035.
The input waveform is produced by a precision pulse generator under software control. Time delays are
measured by a time interval counter (20 ps resolution ) connected to the output. The DS1035 output taps
are selected and connected to the interval counter by a VHF switch control unit. All measurements are
fully automated with each instrument controlled by the computer over an IEEE 488 bus.
DS1035 TEST CIRCUIT
Figure 2
3 of 6
DS1035
ABSOLUTE MAXIMUM RATINGS*
Voltage on Any Pin Relative to Ground
Operating Temperature
Storage Temperature
Soldering Temperature
Short Circuit Output Current
-1.0V to +7.0V
0°C to 70°C
-55°C to +125°C
260°C for 10 seconds
50 mA for 1 second
* This is a stress rating only and functional operation of the device at these or any other conditions above
those indicated in the operation sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods of time may affect reliability.
DC ELECTRICAL CHARACTERISTICS
PARAMETER
Supply Voltage
Active Current
High Level Input Voltage
Low Level Input Voltage
Input Leakage
High Level Output Current
Low Level Output Current
SYMBOL
V
CC
I
CC
V
IH
V
IL
I
L
I
OH
I
OL
0V≤V
I
≤V
CC
V
CC
=4.75V
V
OH
=4V
V
CC
=4.75V
V
OL
=0.5V
V
CC
=5.25V
Period=1µs
TEST
CONDITION
(0°C to 70°C; V
CC
=+5V ± 5%)
MIN
4.75
TYP
5.00
MAX
5.25
35
2.2
-0.5
-1.0
V
CC
+0.5
0.8
+1.0
-1.0
12
UNITS
V
mA
V
V
µA
mA
mA
AC ELECTRICAL CHARACTERISTICS
PARAMETER
Period
Input Pulse Width
Input-to-Tap Output Delay
Output Rise or Fall Time
Power-up Time
SYMBOL
t
PERIOD
t
WI
t
PLH,
t
PHL
t
OR,
t
OF
t
PU
MIN
2 (t
WI
)
100% of
Tap Delay
Table 1
2.0
TYP
(+25°C; V
CC
=5V ± 5%)
MAX
UNITS
ns
ns
ns
2.5
100
ns
ms
NOTES
3
3
CAPACITANCE
PARAMETER
Input Capacitance
SYMBOL
C
IN
MIN
TYP
MAX
10
(T
A
=25°C)
UNITS
NOTES
pF
4 of 6
DS1035
Ambient Temperature:
25°C
±=3°C
Supply Voltage (V
CC
):
5.0V
±=0.1V
Input Pulse:
High: 3.0V
±=0.1V
Low: 0.0V
±=0.1V
Source Impedance: 50Ω=max.
Rise and Fall Time: 3.0 ns max. - Measured between 0.6V and 2.4V.
Pulse Width: 500 ns
Pulse Period: 1
µs
Output Load Capacitance: 15 pF
Output:
Each output is loaded with the equivalent of one 74F04 input gate.
Data is measured at the 1.5V level on the rising and falling edges.
Note:
The above conditions are for test only and do not restrict the devices under other data sheet
conditions.
TEST CONDITIONS
TIMING DIAGRAM
NOTES:
1. All voltages are referenced to ground.
2. @ V
CC
=5 volts and 25°C, delay accuracy on both the rising and falling edges within tolerances given
in Table 1.
3. Pulse width and duty cycle specifications may be exceeded; however, accuracy will be application
sensitive with respect to decoupling, layout, etc.
5 of 6
京公网安备 11010802033920号
EEWORLD
