3021-A-E datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > 3021-A-E

Preview

3021-A-E: DescriptionWide Range LED Power Module; File Size338KB，8 Pages; ManufacturerETC2

Download Datasheet Compare View All

3021-A-E Overview

Wide Range LED Power Module

Preview

Download Datasheet

View All

3021/3023 BuckPuck

Wide Range LED Power Module

DATA SHEET Page 1 of 8

Product Overview

The 3021 and 3023 BuckPuck LED Power Modules are a line of true

current regulated drivers for powering LEDs. The BuckPuck line of

LED drivers is the ideal choice for powering all types of high-

brightness and high-power LED Packages and LED arrays.

The line of BuckPuck LED drivers exhibit high e ciency and require

no external current limiting resistors or additional heat sinking for

operation. A fast response current-sensing circuit makes the 3021

and 3023 ideal for applications where ashing or strobe operation of

the LED(s) is required.

A wide range of options are available including external dc analog

voltage intensity control, TTL/CMOS logic level on/o control (”E”

Version), and set-and-forget internal current limiting (”I” Version).

The standard units are fully potted in an extremely small form factor*

and are provided with a simple 7 pin SIP connection for through-hole

PCB mounting (3021) or 6” 24AWG Colored Leads (3023).

The 3021 and 3023’s built-in regulated 5V reference (E and I versions)

can provide output to power logic circuitry or microprocessor,

eliminating the need for an additional power supply on the circuit board.

Features

DC or AC input voltage up to 32V (24VAC

RMS

)

350mA, 500mA, 700mA, or 1.0A constant current output*

Extremely small form factor* (0.83”x0.83”x0.43”)

The 3021 has a simple 7-pin SIP connection for through-hole

PCB mounting or use with an optional wiring harness (3021Hx)

The 3023 has permanently attached wires

External analog/digital intensity control (TTL compatible)

Optional external potentiometer intensity control (0-100%)

Optional on-board trim adjustment (40-110%)

Output short circuit protection up to 15 seconds

Output open circuit protection

Pulse and strobe capable (control input)

Built-in 5V reference/output to power logic circuitry or µProcessor

Typical Applications

Solar & Landscape Lighting

Architectural Lighting

Track Lighting

Automotive & Marine Lighting

Portable Lighting & Flashlights

Point of Purchase Lighting

Desk & Reading Lamps

Signal & marker Lighting

Flashing & Strobe Lighting

Cabinet & Display Case Lighting

Sign & Channel Letters

Much More...

7-Pin SIP through-hole

PCB mounting

Optional on-board trim

adjustment (40-110%)

* - Custom units can be designed for OEM applications. Contact LUXdrive for more information.

3021

BuckPuck

with optional

wiring harness

(3021HEP)

RoHS

C o m p lia n t

2002/95/EC

LEDdynamics, Inc.

802.728.4533 P

802.728.3800 F

sales@LUXdrive.com

www.LUXdrive.com

Speci cations subject to change without notice. May, 2013 - Rev 3.1

Made

the

USA

3021/3023 BuckPuck

Wide Range LED Power Module

DATA SHEET Page 3 of 8

Speci cations

Output current, 3021-x-x-350, 3023-x-x-350 . .

Output current, 3021-x-x-500, 3023-x-x-500 . .

Output current, 3021-x-x-700, 3023-x-x-700 . .

Output current, 3021-x-x-1000, 3023-x-x-1000

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000mA

Control Pin, adjustment threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.65 V ±5%

Control Pin, shuto threshold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 V ±5%

Control Pin, propagation delay to output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <15 µs

Control Pin, input impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5k ohm

Reference voltage (V

= 7V or greater) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 V

±5%

Optional trim pot adjustment range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40%-110%

External pot adjustment range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0%,1-100%

Maximum ash frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 kHz

Minimum strobe pulse width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 µs

Output rise time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <10 µs

Output fall time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <350 µs

Quiescent current (no load or control pin high) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <4.5 mA

Operating temperature (Tcase). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40-+80°C

Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40-+125°C

Application Information

Description

The 3021/3023 Wide Range LED Power Module is a high e ciency dc to dc converter which delivers a xed output

current by varying the output voltage as required to maintain the speci ed current . A fast response current-sensing

circuit permits the unit to be used in applications where ashing or pulsing of the LEDs is required. Several options

are available allowing for use with many types of LEDs and in a variety of operating modes

Fixed Current Drive

The xed output versions of the 3021/3023 are designed to supply their rated current to one or more LED junctions.

For example, a 350 mA rated unit will drive up to six white 350mA LEDs connected in series at 24V

. Due to the

nature of the buck regulator, the input voltage must always be higher than the total forward voltage drop of the

LED junction(s) connected in series (2.5V for DC models, 4V for AC models). Thus, for a series string of six junctions

having an average forward drop of 3.5V each, the required minimum input voltage will be 23.5V

. A standard

24V

power supply is a good choice for this application.

Figures 4 through 6 show 700mA and 1000mA rated units driving multiple LEDs. Note that parallel strings of LEDs

can be driven directly with no additional circuitry required to ensure current sharing. The nature of the LEDs

themselves will provide su cient current sharing if the parallel strings comprise of 3 or more junctions each.

1 - Measured with single emitter; output current drops slightly with additional series junctions to limit maximum power dissipation.

2 - When Vin > 7VDC

3 - Actual value varies greatly based on input and/or output voltages. Value shown is for V

= 24V

OUTt

=20V

LED load. Actual values will be smaller in most applications.

Speci cations subject to change without notice. May, 2013 - Rev 3.1

LEDdynamics, Inc.

802.728.4533 P

802.728.3800 F

sales@LUXdrive.com

www.LUXdrive.com

Made

the

USA

3021/3023 BuckPuck

Wide Range LED Power Module

DATA SHEET Page 4 of 8

Adjustable Current - On-Board Control - “I” Model

Where the ability to adjust the output current to an intermediate value is required, all output current ratings are

available with an on-board potentiometer. This permits the output current to be varied from approximately 40%

to 110% of the rated value. When measuring the output is required to determine a particular set point, the

following method is recommended:

Temporarily place a 0.1 ohm, 1% resistor in series with the LEDs.

Read the voltage across the 0.1 ohm resistor.

The voltage, in millivolts X 10, will equal the output current in mA.

Because there is a small, high-frequency component in the 3021/3023 output, many multi-meters may give an

incorrect reading when used in the current mode. It has been found that the method described above yields a far

more accurate measurement.

The potentiometers used for the on-board adjustable units are rated for a limited number of rotations (typically

100) and are intended for "set it and forget it" applications. Where frequent adjustments of output current are

needed, the use of units with external adjustment capabilities is recommended.

Adjustable Current - External Control - “E” Model

Figures 10 and 11 show external adjustment con gurations. Both use a 5Kohm, linear taper potentiometer. In

Figure 10, the potentiometer is connected between the internal 5V

reference (Ref) output and the control (Ctrl)

input. When using this con guration, it is important that Vin be 7V

or higher. Figure 11 shows the control

potentiometer being powered by an external 5V

source. When using an external power source for the

potentiometer, the source ground must be common to the LED- output pin. In either con guration, connect the

potentiometer such that clockwise rotation increases the resistance. Note that, because the current through the

potentiometer is less than 5mA, a low power potentiometer may be used.

External On/O Control

Where a manual on/o control is desired, the potentiometer in Figures 10 and 11 may be replaced by a pushbutton

or toggle switch. The output current will be zero when the switch is closed. Figures 12 and 13 show external

dimming control combined with on/o control. The circuit in Figure 13 uses a 2N3906 or equivalent PNP

switching transistor.

External Pulse/Strobe Control

Figures 14 and 15 show two methods for low speed pulsing or high speed ashing operation. In Figure 14, a

5V TTL/CMOS logic signal is applied directly to the control (Ctrl) input of the 3021/3023. The output current will be

zero when the control signal is high. Note that the input needs to source a minimum of 4.75V

into a 1.5Kohm

input impedance. Also, as is the case with a dc control signal, the logic input ground should to be common to the

LED- output terminal.

Figure 15 shows an inverted input con guration using a 2N3906 or other PNP switching transistor. In this case, a

logic high will cause the output to be "on". In either con guration, the rise time of the output will be 10µsec or

less. A pulse frequency up to 10kHz may be used.

Speci cations subject to change without notice. May, 2013 - Rev 3.1

LEDdynamics, Inc.

802.728.4533 P

802.728.3800 F

sales@LUXdrive.com

www.LUXdrive.com

Made

the

USA

3021-A-E Related Products

	3021-A-E	3021-A-I	3021-A-N	3021-D-E	3021-D-E-350	3021-D-I	3021-D-N	3023-A-N	3023-D-E	3023-D-N
Description	Wide Range LED Power Module	Wide Range LED Power Module	Wide Range LED Power Module	Wide Range LED Power Module	Wide Range LED Power Module	Wide Range LED Power Module	Wide Range LED Power Module	Wide Range LED Power Module	Wide Range LED Power Module	Wide Range LED Power Module

Recommended Resources

Simple signal generator for signal tracing

Ladder diagram of spraying process at 5# station

Acousto-optic digital level detector circuit

Power converter circuit suitable for 110V small household appliances

Over-stack trigger AC—SSR internal circuit

Y step-down starting circuit to prevent arcing short circuit between contactor contacts

How can the "Download and Debug" button execute BUILD first?: The company's IAR downloads the program directly when I press the "Download and Debug" button. The IAR at home builds unconditionally before downloading the program after I press the button. It has al...; lyang_c stm32/stm8

Is there any expert who has used lm3s9L97 and urgently needs the schematic diagram of the board?: My senior year graduation project uses lm3s9l97 to make a USB to parallel port. I applied for the chip on Ti tube website, but there is no evaluation board schematic! If any expert has used it or has ...; 轻轨002 Microcontroller MCU

Dear All: Do you have any books on C# serial communication engineering? Both vs2005 and vs2003 are fine. There are too few books on C# now.: Dear All: Do you have any books on C# serial communication engineering, either for vs2005 or vs2003, there are too few books on C# now. If you have any, can you please give me a thumbs up? My email ad...; 0211liucheng Embedded System

Picture video recording solution: Color[/font][/b][b][font=宋体][font=Times New Roman]/[/font][/font][/b][b][font=宋体]Black and white video intercom[/font][/b][b][font=宋体][font=Times New Roman], [/font][/font][/b][b][font=宋体]Access contr...; jamesmold Industrial Control Electronics

Generic code library for an LCD display: LCD display universal code library...; Aguilera Microcontroller MCU

100 Examples of Commonly Used Basic Analog Circuits: Very good commonly used basic circuit very practical!...; 韬奇 Analog electronics

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components