DB3ED2LD datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Mechanical and electronic products> switch> DB3ED2LD

DB3ED2LD: DescriptionSnap Acting/Limit Switch, SPST, Momentary, 19mm, Solder Terminal, Auxiliary Type Actuator, Through Hole-right Angle,; CategoryMechanical and electronic products switch; File Size422KB，4 Pages; ManufacturerThe Cherry Corporation

Download Datasheet Parametric View All

DB3ED2LD Overview

Snap Acting/Limit Switch, SPST, Momentary, 19mm, Solder Terminal, Auxiliary Type Actuator, Through Hole-right Angle,

DB3ED2LD Parametric

Parameter Name	Attribute value
Maker	The Cherry Corporation
Reach Compliance Code	compliant
ECCN code	EAR99
Actuator stroke	19 mm
Actuator type	AUXILIARY TYPE
Other features	ELECTRICAL LIFE AND ELECTRICAL RATING FOR EN ALSO AVAILABLE
body width	9.65 mm
body height	6.5 mm
Body length or diameter	20 mm
Contact (AC) maximum rated R load	.1A@250VAC
Maximum contact current (AC)	0.1 A
Maximum contact voltage (AC)	250 V
Electrical life	6000 Cycle(s)
JESD-609 code	e4
Manufacturer's serial number	DB
Installation features	THROUGH HOLE-RIGHT ANGLE
Maximum operating force	0.18 N
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Maximum pre-travel	15 mm
surface mount	NO
Switch action	MOMENTARY
switch function	SPST
Switch type	SNAP ACTING/LIMIT SWITCH
Terminal surface	SILVER
Termination type	SOLDER

Preview

Download Datasheet

View All

Subminiature Snap Action Switch

DB Series

Features



Precision switch with high repeat accuracy

Models available for operating temperatures up to 120°C

Rated for currents up to 10A @ 250VAC

Range of snap-on auxiliary actuators, two mounting positions



Wide variety of terminal options available

International approvals standard

Mechanical life up to 15 x 10

RoHS Compliant

Electrical Ratings and Operating Life

Switch

Series

DB1

According to EN61058-1

Nominal Load

6A, 250V~

0.1A 80 VDC

10(1.5)A, 250 V~

DB2

DB3

DB5*

DB6*

DB7*

0.1A 80 VDC

0.1A 250 V~

0.1A 80 VDC

1A 250 V~

6A 250 VAC~

10(1.5)A 250 V~

Operation cycles

10,000

50,000

According to UL1054

Nominal Load

5A 125/250 VAC

1A 48 VDC

10.1A 125/250 VAC

¼ HP 125 VAC

0.1A 125/250 VAC

1A 125/250 VAC

1A 48VDC

5A 125/250 VAC

10.1A 125/250 VAC

¼ HP 125 VAC

Operation cycles

6,000

15,000

6,000

100,000

6000

15,000

6,000

Mechanical Life

15 x 10

10 x 10

15 x 10

10 x 10

*Only 85°C Rated

Technical Specifications

Temperature Rating:

Degree of Protection:

Contact Gap

-40°C to 85°C or -40°C to 120°C

IP50

< 3mm (μ)

Material Specifications

Base:

Cover:

Actuator button:

Contacts:

Terminals:

Auxiliary actuator:

PET (UL 94 V-0)

PBT (UL 94 V-0)

PBT (UL 94 V-0) 120°C

POM (UL 94 HB) 85°C

AuAgPt (Crosspoint),

AgNi,

CuZn (silver plated)

Stainless steel or plastic

Proof Tracking Index

PTI 175

UL File Number:

E314201

Specifications subject to change

Recommended Resources

Interface circuit between CMOS and PMOSb

Identification sensor amplification circuit diagram

Nine-digit key code lock circuit

TA7271P power amplifier circuit

Closed-loop three-phase multivibrator

Single power supply low power instrument amplifier circuit

[Sharing] Forum usage tips and methods: Since this is a comprehensive technology area, can you share some tips and methods used in the forum? If you think it is good and convenient, even if it is just a light click, I will take out my chip ...; Sur Integrated technical exchanges

An important operation about converting Altium Designer to pads: [i=s]This post was last edited by spacexplorer on 2015-5-11 16:47[/i] I worked overtime to draw a board a few days ago. The PCB frame was transferred from AD. There were always problems when it came t...; spacexplorer PCB Design

Chapter 7 Bulk Equipment: Written by Ogawa Studio, this book is written for the LM3S USB chip. The uploaded ones are all drafts and have not been revised . There may be many shortcomings. I hope netizens will forgive me! QQ:26...; paulhyde Microcontroller MCU

[Repost] AVR driver floppy drive motor program: /*Use mega32 three port lines to drive the floppy drive motor. PA2 connects to LB1833 ENA1\2 pin; PA1 connects to LB1833 IN1 pin; PA0 connects to LB1833 IN2 pin. **************************************...; 黑衣人 Microchip MCU

Regarding the connection number calculation problem: The controller and communication module in the AB control system each have their own upper limit on the number of connections. For example, ControlLogix has an upper limit of 250 connections, 1756-CNB...; eeleader Industrial Control Electronics

Please help me with ADC voltage divider sampling problem: I use adc10 for sampling, but the internal resistance of adc10 is very small. If I don't use a follower, is there any good solution at the software level?...; I举个例子I Microcontroller MCU

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components