E13C7E1F-175M datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Passive components> oscillator> E13C7E1F-175M

E13C7E1F-175M: DescriptionCRYSTAL OSCILLATOR, CLOCK, 175 MHz, LVPECL OUTPUT; CategoryPassive components oscillator; File Size144KB，2 Pages; ManufacturerECLIPTEK; Websitehttp://www.ecliptek.com; Environmental Compliance

Download Datasheet Parametric View All

E13C7E1F-175M Overview

CRYSTAL OSCILLATOR, CLOCK, 175 MHz, LVPECL OUTPUT

E13C7E1F-175M Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Maker	ECLIPTEK
Reach Compliance Code	compliant
Other features	TRISTATE ENABLE/DISABLE FUNCTION; COMPLEMENTARY OUTPUT
maximum descent time	1 ns
Frequency Adjustment - Mechanical	NO
frequency stability	25%
JESD-609 code	e4
Manufacturer's serial number	E13C7
Installation features	SURFACE MOUNT
Nominal operating frequency	175 MHz
Maximum operating temperature	70 °C
Minimum operating temperature
Oscillator type	LVPECL
Output load	50 OHM
physical size	7mm x 5mm x 2mm
longest rise time	1 ns
Nominal supply voltage	3.3 V
surface mount	YES
maximum symmetry	60/40 %
Terminal surface	Nickel/Gold (Ni/Au)

Preview

Download Datasheet

View All

E13C7

Series

• RoHS Compliant (Pb-Free)

• LVPECL Output Oscillators

• 3.3V Supply Voltage

• AT-Cut Fundamental Mode Inverted Mesa Crystal

• Ceramic 6-pad SMD Package

• Stability to 25ppm

• Tri-State Output

• Complementary Output

• Available on Tape and Reel

• Wide Range of Available Frequencies

ELECTRICAL SPECIFICATIONS

Nominal Frequency

E13C7

2.0

7.0

5.0

OSCILLATOR

38.880MHz to 77.760MHz, and 78.125MHz, 80 MHz, 80.157MHz, 85MHz, 87.125MHz, 90MHz, 100MHz,

106.25MHz, 110MHz, 119MHz, 120MHz, 122.888MHz, 124.4MHz, 125MHz, 127MHz, 128MHz, 133MHz,

133.333MHz, 137.472MHz,150MHz, 155.52M, 156.25MHz, 161.1328MHz , 162.5M, 166M, 170MHz,

175MHz, 187.5MHz, 200MHz, 208MHz

Operating Temperature Range

Storage Temperature Range

Supply Voltage (V

)

Input Current

Frequency Tolerance / Stability

Inclusive of All Conditions: Calibration Tolerance at 25°C,

Frequency Stability over the Operating Temperature Range,

Supply Voltage Change, Output Load Change, 1st Year

Aging at 25°C, Shock, and Vibration

Output Voltage Logic High (V

)

Output Voltage Logic Low (V

)

Rise Time / Fall Time

Duty Cycle

Load Drive Capability

Logic Control / Additional Output

Tri-State Input Voltage

of 70% of V

Minimum

No Connection

of 30% of V

Maximum

Standby Current

Start Up Time

RMS Phase Jitter

Typical Phase Noise

< 77.760MHz FJ = 12kHz to 20MHz

> 77.760MHz FJ = 12kHz to 20MHz

Fo=155.520MHz

Without Load

20% to 80% of waveform

at 50% of waveform

0°C to 70°C, or -40°C to +85°C

-55°C to 125°C

3.3V

±5%

75mA Maximum

±100ppm, ±50ppm, or

±25ppm Maximum

-1.025V

Minimum

-1.620V

Maximum

1 nSeconds Maximum

50 ±10(%)

50 ±5(%)

50 Ohms into V

-2.0V

No Connect and Complementary Output or

Tri-State and Complementary Output

Enables Output

Disables Output: High Impedance

10µA Maximum

10 mSeconds Maximum

2 pSec Maximum

1 pSec Maximum

-60dBc/Hz at 10Hz Offset

-95dBc/Hz at 100Hz Offset

-124dBc/Hz at 1kHz Offset

-143dBc/Hz at 10kHz Offset

MANUFACTURER

Recommended Resources

MF-52 pointer multimeter circuit

Y-△ started air compressor control circuit

Single line remote forward and reverse control circuit

Negative 2V-12V reference voltage source

Precision voltage reference LM399 circuit diagram

Light controlled electronic switch

Intelligent tracking car: [i=s]This post was last edited by paulhyde on 2014-9-15 09:43[/i] Can anyone help me?...; yuwenfeng10 Electronics Design Contest

Section 3 LMR33630-Q1: An excellent choice for primary power supply: In the first two sections, we discussed the most popular interfaces of T-BOX: PHY and CAN. In the following sections, I will introduce the power supply, which is mainly divided into Wide Vin BUCK, Low...; alan000345 TI Technology Forum

What tool can be used to read the binary content of the ARM chip?: [b][url=http://www.amobbs.com/thread-979583-1-1.html]What tool can be used to read the binary content of the ARM chip? Note that it is not to restore the source file, but to read the binary file and b...; tongchou ARM Technology

Beaglebone Black introduction and information link summary: Open source hardware is very popular abroad, but not many people in China play with it, which directly leads to a serious lack of information on Chinese forums... But this can't stop the charm of Beag...; wytalfred MCU

[Help] Warning problem when compiling EW8051: [size=16px]When compiling with EW8051, many of the following two warnings appeared, but I just can't find the reason. Please help me, what is the reason for this warning. Last line of file ends withou...; sunline Embedded System

C6748 spi0 burn bin file: 1. My 6748 board uses spi0 cs0 to connect to spi flash. Is there any problem with the above settings? 2. The ccs loader I use is C6748\OMAP-L138_FlashAndBootUtils_2_40\OMAP-L138_FlashAndBootUtils_2_40...; zhaiwenrui DSP and ARM Processors

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components