Figure 7. Standard PECL Output Configuration Figure 8. Single Resistor Termination Scheme
Resistor values are typically 140 ohms for
3.3V operation.
Resistor values are typically 84 ohms for 2.5V
operation.
The VCC6 incorporates a standard PECL output scheme, which are un-terminated emitters as shown in Figure 7. There are numerous application notes on
terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 8, and a pull-up/pull-down scheme as
shown in Figure 9. An AC coupling capacitor is optional, depending on the application and the input logic requirements of the next stage.
LVDS Application Diagrams
V
CC
LVDS
Driver
100
LVDS
Receiver
LVDS
Driver
100
Receiver
OUT+
OUT-
Figure 10 Standard LVDS
Output Configuration
Figure 11. LVDS to LVDS Connection, Internal 100ohm
Figure 12. LVDS to LVDS Connection
Some LVDS structures have an internal 100 ohm resistor on the
External 100ohm and AC blocking caps
input and do not need additional components.
Some input structures may not have an internal 100 ohm
resistor on the input and will need an external 100ohm
resistor for impedance matching. Also, the input may have
an internal DC bias which may not be compatible with
LVDS levels, AC blocking capacitors can be used.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-termi-
nated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
Unfortunately, this is only a concept product so far. The designer said that it can realize any function of a mobile phone through Bluetooth connection. I don't understand, why not integrate a mobile ...
[i=s] This post was last edited by blacklili on 2015-6-30 10:35 [/i] [align=left][b]1. [/b][b][font=宋体]Design goal [/font][/b][/align][align=left] [font=宋体]In the quadcopter, 11.1V aircraft battery is...
My colleague's classmate recommended me to Huawei Software. I felt that there were indeed too many embedded talents and I didn't know when I could become a great person, so I decided to go. First, the...
How can I display specific characters on the WinCE desktop? These characters are strings that I specify. How can I display these characters on the WinCE desktop? Thank you! EVC Development...
In recent years, as energy consumption and environmental protection issues have attracted people's attention, my country's solar photovoltaic power generation industry has shown a rapid development...[Details]
Function List and Notes (lower-level driver part) 1. IO port initialization: control IO and communication IO. Control includes power control, reset and low power mode. Communication is the serial po...[Details]
Serial Port: 一. USART_ITConfig(USART1, USART_IT_TXE, ENABLE): As long as the transmit register is empty, there will always be an interrupt. Therefore, if you are not sending data, turn off the tran...[Details]
After studying the F4 FSMC method to drive the touch screen for a few days, I have gained some understanding, which are listed below. The unorganized record is only for my own reference in the future...[Details]
Unlike three years ago, today's
artificial intelligence
is no longer just a floating concept, and the venture capital circle has begun to explore the various possibilities of this technolog...[Details]
This paper proposes a design scheme for an embedded CNC system based on ARM and FPGA. The software and hardware design of the ARM system, the implementation method of hardware fine interpolation ...[Details]
As photovoltaic power stations come into people's view, people are paying more and more attention to them. Recently, some netizens asked me how to match the inverter and components of photovoltaic ...[Details]
At the beginning, I used the stdlib library. Recently, I found that the cube library is more and more widely used, so I started to use the cube library to complete the ADC multi-channel acquisition e...[Details]
Site conditions: 1. AD acquisition, DMA transmission; AD is set to single-channel continuous mode, DMA is set to single-shot mode. The upper threshold of the AD analog watchdog setting is less than t...[Details]
The pins of stm32 have two uses: GPIO (general purpose io) and AFIO (alternate function io) For some pins (depending on the chip), neither of these two uses exists. For example, in 64-pin products, O...[Details]
I have encountered many problems when tinkering with LD driver recently. I will record them one by one below. Otherwise, who will remember who in five hundred years? 1. Configuration issues of multi-...[Details]
Today I am using the AD function of the stm8s microcontroller. There are ten channels from AN0 to AN9 on the microcontroller. I want to use only three of them, AN5 to AN7. //ADC initialization void A...[Details]
Summary of STM32 peripheral DMA usage: 1. Select DAM mode according to your needs: (1) Circular mode—DMA_Mode = DMA_Mode_Circular (2) Normal mode—DMA_Mode = DMA_Mode_Normal 2. For Chanel3 of DMA1, t...[Details]
Requirements: Set timer T1 as an external event counter, count 500 pulses every time, then switch T1 to timing mode and output a positive pulse with a width of 10ms at P1.2. Over and over again. A...[Details]
Microchip MCU
京公网安备 11010802033920号
EEWORLD
