Figure 7. Standard PECL Output Configuration Figure 8. Single Resistor Termination Scheme
Resistor values are typically 120 to 240 ohms
for 3.3V operation.
Resistor values are typically 82 to 120 ohms
for 2.5V operation.
Figure 9. Pull-Up Pull Down Termination
Resistor values are typically for 3.3V operation
For 2.5V operation, the resistor to ground is 62
ohms and the resistor to supply is 240 ohms
The VCC6 incorporates a standard PECL output scheme, which are un-terminated emitters as shown in Figure 7. There are numerous application notes on
terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 8, and a pull-up/pull-down scheme as
shown in Figure 9. An AC coupling capacitor is optional, depending on the application and the input logic requirements of the next stage.
LVDS Application Diagrams
V
CC
LVDS
Driver
100
LVDS
Receiver
LVDS
Driver
100
Receiver
OUT+
OUT-
Figure 10 Standard LVDS
Output Configuration
Figure 11. LVDS to LVDS Connection, Internal 100ohm
Figure 12. LVDS to LVDS Connection
Some LVDS structures have an internal 100 ohm resistor on the
External 100ohm and AC blocking caps
input and do not need additional components.
Some input structures may not have an internal 100 ohm
resistor on the input and will need an external 100ohm
resistor for impedance matching. Also, the input may have
an internal DC bias which may not be compatible with
LVDS levels, AC blocking capacitors can be used.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-termi-
nated, and if it one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
[i=s]This post was last edited by qwqwqw2088 on 2017-4-24 15:01[/i] Analysis of mobile phone RF circuit Analysis of typical functional modules in RF circuit, transceiver circuit, phase-locked loop cir...
at89s52 Changzhen is 11. 0592 eeprom is at24c02. When I write 10 1s to eeprom and then read it out, (hexadecimal) 31 20 31 20 31 20 one is right and one is wrong. It is very regular. Please help. What...
The screen printing process of the circuit board can be divided into 9 parts and 56 variables, which requires everyone to have the correct operating procedures or the following phenomena will occur. N...
[size=14px][size=5][color=#ffa500][url=https://www.eeworld.com.cn/a17396]Japanese Illustrated Book Series: Illustrated Internet of Things[/url][/color][/size][/size] [font=微软雅黑][size=14px][size=4]Japa...
I'm going to explain what wince is. Windows 98, Windows 95, and Windows ME are based on the 9X kernel, while Windows NT, Windows 2000, Windows XP, and Windows Vista are based on the NT kernel. Is winc...
UHF and HF are both general technology categories, but each category has independent supporting protocols. HF is more consistent in the 13.56MHz frequency band, although there are many internation...[Details]
Project Overview
The micro urine analyzer we designed can detect ten parameters of urine, including white blood cells, nitrite, urobilinogen, protein, pH value, occult blood, specific g...[Details]
1 Introduction
The multifunctional monitor is a commonly used clinical medical device. It can display the patient's electrocardiogram (ECG), respiration (RESP), blood oxygen saturation (SP...[Details]
Until now, designers have faced a trade-off in ADC selection. Pipeline converters offer high resolution and wide dynamic range, but their power consumption is quite high. The alternative, discrete ...[Details]
No other sector is feeling the pressure for change more acutely than the healthcare industry. Healthcare organizations and services are desperate to reduce costs, but the challenge is to do so without...[Details]
With the rapid development of digital technology, various digital display screens have emerged, including LED, LCD, DLP, etc. There are various control systems for various digital large screens, in...[Details]
Engineers who are new to wireless design and wireless product development need to master the basics of
RF measurement
. In many cases, this process is to enable engineers who have been engag...[Details]
Third generation (3G) mobile phones offer a variety of features with more functionality. As consumers enjoy the latest and better features of these communication devices, they continue to demand lo...[Details]
DC regulated power supply is a commonly used electronic device, which can ensure stable output voltage when the grid voltage fluctuates or the load changes. A low ripple, high-precision regulated p...[Details]
introduction
The most common flight state of a fixed-wing aircraft is horizontal flight. If it is allowed to fly at a large angle, the action cannot be maintained all the time. If it is al...[Details]
Preface
Phase-modulated pulse signals can achieve a large compression ratio. As a commonly used pulse compression signal, they are widely used in modern radar and communication systems. Wi...[Details]
This article first briefly introduces the working principles of current mode and voltage mode and their respective advantages and disadvantages; then discusses the ideal voltage mode using output c...[Details]
Demand Analysis
In an era of rapid information development, the process of electronicization of the financial system has also been greatly accelerated. As a platform that provides services 24 ...[Details]
Today's mobile phone production testing faces an increasingly complex environment, with challenges of multiple frequency bands and multiple standards, pressure on production test speed, and pres...[Details]
Semiconductor devices used in high-end computing (advanced microprocessors) and consumer electronics (graphics and gaming chipsets) devices generally provide data rates up to 6.4Gbps through hig...[Details]
Test/Measurement
京公网安备 11010802033920号
EEWORLD
