EEWORLDEEWORLDEEWORLD

Part Number

Search

8222LBMAB20LEN5C

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 10V, 20% +Tol, 20% -Tol, 2200uF
CategoryPassive components    capacitor   
File Size46KB,3 Pages
ManufacturerFenghua (HK) Electronics Ltd.
Download Datasheet Parametric View All

8222LBMAB20LEN5C Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 10V, 20% +Tol, 20% -Tol, 2200uF

8222LBMAB20LEN5C Parametric

Parameter NameAttribute value
MakerFenghua (HK) Electronics Ltd.
package instruction,
Reach Compliance Codeunknown
ECCN codeEAR99
capacitance2200 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
diameter12.5 mm
dielectric materialsALUMINUM (WET)
length20 mm
Manufacturer's serial numberLE(10V)
negative tolerance20%
Number of terminals2
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
Package formRadial
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)10 V
seriesLE(10V)
Terminal pitch5 mm
ALUMINUM ELECTROLYTIC CAPACITOR (CD288H LE)
LE FEATURES
Wide temperature high frequency and ultra low impedance
D 8mm with top safety vent construction
For switching power supplies and other industrial electronic products applications
SPECIFICATIONS
Item
Rated Voltage Range
Operating Temperature
Range
Nominal Capacitance Range
Capacitance Tolerance
Performance Characteristics
6.3V.DC~100V.DC
-40°C~+105°C
0.1 F~10000 F
±20%(M,+25°C,120Hz)
After application of rated voltage for 2 minutes: I 0.01CV or 3 A(Whichever is greater)25°C
Leakage Current
C: Nominal Capacitance in F; V: Rated Working Voltage in V
When capacitance is over 1000 F, tan shall be added 0.02 with increase of every 1000 F
Dissipation Factor
Rated Working Voltage(V)
(tan )
6.3
0.24
10
0.20
16
0.16
6.3~16
5
7
25
0.14
35
0.12
50
0.10
tan ( MAX) (25°C,120Hz)
Rated Working Voltage
25~100
4
3
Temperature Stability
Impedance Ratio
(120Hz)
Z-25°C/Z+20°C
Z-40°C/Z+20°C
After application of rated working voltage and maximum permissible ripple current specified at +105°C for 1000
hours, Capacitors meet the characteristics requirements measured at +25°C listed below:
Load Life
Leakage Current
Less than the initial specified value
Less than 150% of the initial specified value or 0.4
Within ±20% of the initial measured value
Capacitance Change
After Leaving capacitor under no load at +105°C for 500 hours, Capacitors meet the characteristics listed
Shelf Life
above.
MULTIPLIER FOR RIPPLE CURRENT
Frequency coefficient
Freq(Hz)
Cap(uF)
6.3~35
50~63
100~250
350~450
Temperature coefficient
Ambient Temperature(°C)
Factor
+105
1.0
+85
1.7
+65
2.1
1000
1000
50(60)
0.8
0.8
0.8
0.8
0.8
0.8
100(120)
1
1
1
1
1
1
1K
1.1
1.2
1.5
1.2
1.6
1.3
10K
1.2
1.3
1.7
1.3
1.9
1.5
1000
1000
δ
tan
www.fenghua.com
1/3
μ
μ
μ
μ
μ
δ
μ
δ
δ
≥ φ
63
0.09
100
0.08
Tms320F2812 connection problem
The newly welded board has the following problems. Please help me. Thank you. Error connecting to the target: Error 0x00001200/-1166 Error during: OCS, Target, Lost processor clock. Device may be oper...
l313553 DSP and ARM Processors
ADC10 continuous sampling problem
int temp[count]; void main() { WDTCTL=WDTPW+WDTHOLD; ADC10_init(); _EINT(); while(1) { ADC10CTL0 |= ENC + ADC10SC; // Sampling and conversion start __delay_cycles(1000); } void ADC10_init(void) { ADC1...
yumin Microcontroller MCU
mkjf.jffs2 problem encountered by S3C44B0+uClinux+jffs2
Hardware development environment: s3c44b0+sst39LF160 (norflash) Software environment: uClinux (2.4) According to the information found on the Internet, the partitions have been transplanted. However, ...
zijin99 Linux and Android
How to make Char[8] correspond to Int[4] one by one? That is, the address of Char[0] is the same as the address of Int[0]
RT, do not use #define Int[i] Char[i*2]*0x100+zero[i*2-1]...
请求权 Embedded System
Please help me modify the simulation diagram of this programmable amplifier circuit
Use counter and analog switch CD4066 to design a gain adjustable amplifier circuit , and use MULTISIM to simulate .Here are the original circuit diagram and the circuit diagram I designed. Please help...
donkey5522 Analog electronics
How to add a pull-up resistor to the 89C51 P0 port
Question 1. How to add an external pull-up device to the 89C51 P0 port? What is the specific connection method? 2. Please explain the difference between the internal pull-up resistor of the P1 port an...
glj1001 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 974  1942  408  1307  2806  20  40  9  27  57 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号