The data is reference only. Electrical characteristics vary depending on environment or measurement condition.
TAIYO YUDEN reserves the right to make change to the data at any time without notice.
Before making final selection, please check product specification.
■
Notice for TAIYO YUDEN Products
for
High Quality Equipment
Please read this notice before using the TAIYO YUDEN products.
!
products.
REMINDERS
■
Please conduct validation and verification of our products in actual condition of mounting and operating environment before using our
■
The product listed in this spec sheet is intended for use in general electronic equipment (e.g., AV equipment, OA equipment, home electric
appliances, office equipment, information and communication equipment), medical equipment classified as Class I or II by IMDRF, industrial
equipment, and automotive interior applications, etc. Please be sure to contact TAIYO YUDEN for further information before using the product
for any equipment which may directly cause loss of human life or bodily injury (e.g., transportation equipment including, without limitation,
automotive powertrain control system, train control system, and ship control system, traffic signal equipment, medical equipment classified as
Class III by IMDRF).
Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g., aerospace equipment,
aviation equipment*, medical equipment classified as Class IV by IMDRF, nuclear control equipment, undersea equipment, military
equipment).
*Note:
There is a possibility that our products can be used only for aviation equipment that does not directly affect the safe operation of aircraft (e.g., in-flight
entertainment, cabin light, electric seat, cooking equipment) if such use meets requirements specified separately by TAIYO YUDEN. Please be sure to
contact TAIYO YUDEN for further information before using our products for such aviation equipment.
When our products are used even for high safety and/or reliability-required devices or circuits of general electronic equipment, it is strongly
recommended to perform a thorough safety evaluation prior to use of our products and to install a protection circuit as necessary.
Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way responsible for any damages
incurred by you or third parties arising from use of the product listed in this spec sheet for any equipment requiring inquiry to TAIYO YUDEN or
prohibited for use by TAIYO YUDEN as described above.
■
Information contained in this spec sheet is intended to convey examples of typical performances and/or applications of our products and is not
intended to make any warranty with respect to the intellectual property rights or any other related rights of TAIYO YUDEN or any third parties
nor grant any license under such rights.
■
Please note that the scope of warranty for our products is limited to the delivered our products themselves and TAIYO YUDEN shall not be in
any way responsible for any damages resulting from a fault or defect in our products. Notwithstanding the foregoing, if there is a written
agreement (e.g., supply and purchase agreement, quality assurance agreement) signed by TAIYO YUDEN and your company, TAIYO YUDEN will
warrant our products in accordance with such agreement.
■
The contents of this spec sheet are applicable to our products which are purchased from our sales offices or authorized distributors
(hereinafter “TAIYO YUDEN’s official sales channel”). Please note that the contents of this spec sheet are not applicable to our products
purchased from any seller other than TAIYO YUDEN’s official sales channel.
■
Caution for Export
The product listed in this spec sheet may require specific procedures for export according to “U.S. Export Administration Regulations”, “Foreign
Exchange and Foreign Trade Control Law” of Japan, and other applicable regulations. Should you have any questions on this matter, please
Is there anyone debugging SPI communication under S3C6400? Why is mine so strange? When it is set to receive mode and the data source is not connected, the SPI interrupt will be triggered continuously...
485 point-to-multiple communication, using modbus communication protocol, daisy-type connection, FPGA sends data, and two devices are mounted to receive data (address 01 and 02). It is sent in serial ...
When using EMWIN PC simulation, there is no SAMPLE folder in the VC project. Please help me! I am using Visual studio 2017, the latest one under simulation file....
A device was returned for repair in the project. During the investigation, it was found that the BOOT program was missing, the application program was normal, and the BOOT area stored garbled code. Th...
Light display with delay program After the previous stage of learning, we finally wrote a program that can control the change of light. In practical applications, this program can be used to contro...
In the
AI
boom, the most talked about is
neural network
. However,
AI
is much more than that. Let's learn about the relevant content with the network communication editor.
...[Details]
Regarding the PHY construction of LWIP, the PHY chip used is LAN8720A, RMII mode. Regarding the hardware connection part, the Atomic board F407 is used, and the hardware connection is as follows: ...[Details]
As the weather gets colder, the way the north and south spend the winter has become a hot topic and people talk about it. Although the north is particularly cold, because there is heating, it can s...[Details]
When STM32 uses JTMS (PA13) and JTCK (PA14) as normal I/O ports, add the following code before initialization (the order cannot be reversed): RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE); G...[Details]
OSC_IN and OSC_OUT are external crystal pins by default. If you do not use an external crystal oscillator on the STM32, how to connect OSC_IN and OSC_OUT If you use the internal RC oscillator instead...[Details]
The following comes from - "cortex-M3 Definitive Guide" Special function register group: Program Status Registers (PSRs or xPSRs) Interrupt mask register group (PRIMASK, FAULTMASK, and BASEPRI) ...[Details]
International Solar Photovoltaic Network News: On November 21, Australia's SMA Solar Technology Co., Ltd. signed a contract with the local government to provide photovoltaic inverters with an insta...[Details]
With the development of electronic devices, more and more people pay attention to flexible electronic devices, which refer to electronic devices that can still work under certain deformation condit...[Details]
#include MSP430x12x2.h #define TEM_ADC_CHL 0x0a void InitSys(void); void Read_ADC(unsigned int INCH_channel); void ADC_TO_TEM(void); unsigned int ADC_sample_val; unsigned int long temp1,temp2;...[Details]
MSP430 uses ADC10 to measure the voltage of the temperature diode inside the chip #include "msp430x22x4.h" //This program uses ADC10 to measure the voltage of the temperature diode inside the chip ...[Details]
China has become the world's largest demander of
industrial robots
, with a stable market development. Automobile and parts manufacturing are still the main application areas of industrial
...[Details]
In October 2017, NVIDIA announced a new member of the Drive PX family of autonomous driving computing platforms at its ecosystem conference GTC Europe , codenamed "Pegasus". "Pegasus" is expected ...[Details]
Principle Description This example designs a clock with time reporting function and work and rest time control. It uses the 2 Hz time base of SPCE061A single chip microcomputer to calculate the...[Details]
Samsung has officially released its mobile phone chips. Meizu's recently released Meizu S6 uses Samsung 's Exynos7872 chip. Foreign media reports indicate that Samsung is trying to use its industr...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
