Ruthenium oxide dielectric offers superior resistance
to the elements.
3) Electrodes not corroded by soldering
Thick film makes the electrodes very strong.
4) Leading the world in development and mass produc-
tion.
Since start of production in 1982 (first in the wold), this
component has established a solid reputation as a
general–purpose chip resistor.
5) ROHM resistors have approved ISO–9001 certifica-
tion.
Design and specifications are subject to change with-
out notice. Carefully check the specification sheet be-
fore using or ordering it.
!Ratings
Item
Rated power
Conditions
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70
°C
.
100
80
60
40
20
0
Specifications
0.125W (1 / 8W)
[0.100W (1 / 10W)]
∗
at 70°C
POWER LOAD (%)
– 55
0
70
100
155
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation. If the value
obtained exceeds the maximum operating voltage, the voltage rating
is equal to the maximum operating voltage.
E: Rated voltage (V)
E = P× R
P: Rated power (W)
R: Nominal resistance (Ω)
Nominal resistance
Operating temperature
* At power rating of 0.1W, maximum overload voltage and maximum intermittent overload voltage are 300V.
Max. operating voltage
150V
200V
(300V)
∗
Max. overload voltage
Max. intermittent overload voltage 200V
(300V)
∗
See Table 1.
– 55
°C
to + 155
°C
MCR10
Resistors
Jumper type
Resistance
Rated current
Peak current
Max. 50mΩ
2A
10A
J ( ± 5%)
Table 1
Resistance tolerance
F ( ± 1%)
Resistance range
(Ω)
10
≤
R
≤
2.2M (E24,96)
1.0
≤
R
<
2.2
2.2
≤
R
<
10
10
≤
R
<
10M
(E24)
(E24)
(E24)
Resistance temperature coefficient
(ppm /
°C)
± 100
500 ± 350
± 500
± 200
Operating temperature – 55°C to + 155°C
!Before
using components in circuits where they will be exposed to transients such as pulse loads (short–duration, high– level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
MCR10
Resistors
!Characteristics
Characteristics
DC resistance
Resistance temperature
characteristics
Short time overload
±
(2.0% + 0.1Ω)
Specifications
Chip resistance
Jumper type
F:
±
1%
J:
±
5%
Max. 50mΩ
Test method
JIS C 5202 5.1
Applied voltage: A
JIS C 5202 5.2
Test conditions: + 25 / – 55 / + 25 / + 125°C
JIS C 5202 5.5
Rated voltage (current):
×
2.5, 5s.
Maximum overload voltage: 200V
JIS C 5202 5.6
Test voltage: 100V, 1min.
Assembled state
Metal block
observation
point A
Insulation plate
See Table 1.
Max. 50mΩ
Min. 1,000MΩ between terminal and board
Insulation resistance
Test resistor
Metal plate
Observation Insulation
sheath
R 0.5
point B
Spring-loaded
pressure
Withstand voltage
Do not damage insulation or cause a short circuit.
±
(5.0% + 0.1Ω)
JIS C 5202 5.7
Test voltage: 500V
JIS C 5202 5.8
Rated voltage (current):
×
2.5
(1s: ON – 25s: OFF)
×
10,000cyc.
JIS C 5202 6.1
JIS C 5202 6.4
Soldering conditions: 260
±
5°C
Soldering time: 10
±
1s.
JIS C 5202 6.5
Rosin methanol: (25%WT)
Soldering conditions: 235
±
5°C
Soldering time: 2.0
±
0.5s.
JIS C 5202 7.2
155°C
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.10
Rated voltage (current), 70°C
1.5h: ON – 0.5h: OFF
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.9
Rated voltage (current), 60°C, 90%RH
1.5h: ON – 0.5h: OFF
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.5
85°C, 85%RH
Test time: 1,000 to 1,048 hrs.
JIS C 5202 7.4
Test temperature: – 55°C to + 125°C 100cyc.
JIS C 5202 6.9
Room temperature, static immersion, 1 min.
Solvent: Isopropyl alcohol
Intermittent overload
Terminal strength
(against bending of circuit board)
Resistance to soldering heat
Max. 50mΩ
±
(1.0% + 0.05Ω)
Max. 50mΩ
There must be no mechanical damage.
±
(1.0% + 0.05Ω)
Max. 50mΩ
Outside must not be noticeably damaged.
95% of terminal surface must be covered by
new soldering, and there must be
no soldering corrosion.
Solderability
Resistance to dry heat
±
(3.0% + 0.1Ω)
Max. 100mΩ
Endurance
(under load in damp environment)
±
(3.0% + 0.1Ω)
Max. 100mΩ
Endurance
(steady state)
±
(3.0% + 0.1Ω)
Max. 100mΩ
Resistance to humidity
(steady state)
±
(3.0% + 0.1Ω)
Max. 100mΩ
Temperature cycling
±
(1.0% + 0.05Ω)
Max. 50mΩ
Resistance to solvents
Max. 50mΩ
±
(0.5% + 0.05Ω)
Markings must not be dissolved away.
MCR10
Resistors
!External
dimensions
(Units: mm)
0.4 ± 0.2
No.
0.4 ± 0.2
2.0 ± 0.1
0.55 ± 0.1
Material
Thick dielectric glaze of ruthenium
(only silver used for jumper)
Thick film of palladium-silver for primary electrode
Nickel-coated secondary electrode
External electrode coated with tin and lead
Alumina substrate
1.25 ± 0.1
Overcoating
!Packaging
Reel
Taping
P
0
P
2
P
1
φD
0
E
F
B
0
08
06
04
02
02
04
06
08
W
A
B
D
A
0
Heat crimp cover/Tape
Thick paper (Underside paper tape) Chip resistor Square punchout hole
Welcome to Power Design Tips! With today's emphasis on the need for more efficient and lower cost power solutions, we have created this column to provide you with some helpful tips on a variety of pow...
TI's CC3220R is a SimpleLink Wi-Fi and Internet of Things (IoT) single-chip wireless MCU platform, including Wi-Fi, Bluetooth low energy, Sub-1 GHz and main MCU and a rich tool portfolio. The applicat...
The difference between switch and if If you are just comparing numbers or characters, it is recommended to use switch, because it only takes out the variable value once in the initial switch brackets,...
I use TIMERB3 to generate an interrupt every few milliseconds, and connect the P2 port to a key (F133). I use the P2 port interrupt to perform some key operations, but now I feel that the key operatio...
Nowadays, mobile phones have gradually become an indispensable tool for people's communication and a necessity in life. "Head-down people" can be seen almost everywhere in daily life. Countless people...
introduction STM32 has many registers, which are difficult to remember, so the official packaged two sets of library functions. One is the standard library, but the official has not updated it on F7,...[Details]
Serial Port: 一. USART_ITConfig(USART1, USART_IT_TXE, ENABLE): As long as the transmit register is empty, there will always be an interrupt. Therefore, if you are not sending data, turn off the tran...[Details]
As many companies listed with
the concept of
touch screen
begin to "transform and upgrade", the official voice of the TP industry is getting smaller and smaller. At the same time, the list o...[Details]
Recently, Zhejiang Lipu Crushing Equipment Co., Ltd. invested 50 million yuan to build a new "annual production of 1,200 high-efficiency and energy-saving ultra-fine pulverizer construction project...[Details]
STM32 ADC multi-channel conversion Description: Use ADC to continuously collect 11 analog signals and transfer them to memory through DMA. ADC is configured to scan and continuously convert mode,...[Details]
Summary of STM32 peripheral DMA usage: 1. Select DAM mode according to your needs: (1) Circular mode—DMA_Mode = DMA_Mode_Circular (2) Normal mode—DMA_Mode = DMA_Mode_Normal 2. For Chanel3 of DMA1, t...[Details]
Getting to the bottom of blockchain
Since last year, blockchain has become the hottest word in both the financial and non-financial circles. Some people use it as a gimmick to engage in va...[Details]
For complex calculations, the speed of the microcontroller is too slow. The best way is to manually calculate all the results in advance, store them in ROM in sequence, and then directly check the re...[Details]
A group of young people who looked like they were in their twenties or thirties were squatting on the edge of the factory flower bed. Some were looking at their phones helplessly, while others were...[Details]
At the early morning of November 17th, Beijing time, at the Global Supercomputing Conference held in Denver, the United States, the "nonlinear earthquake simulation" application completed by the te...[Details]
Today, the country attaches great importance to the Internet of Things, and the Internet of Everything has become the vision of all people in related industries. However, at the same time, masterin...[Details]
As one of the four major Chinese cool alliances, ZTE Mobile undoubtedly has a relatively deep foundation. However, this mobile phone brand has gradually declined in recent years. Now it is hoping t...[Details]
A. The first method is the ordinary IO high and low level driving method ; operating environment: S3F9454, Fosc = 3.2MHz without frequency division ; P2.0 is the buzzer ou...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
