D3B4S8JA datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Mechanical and electronic products> switch> D3B4S8JA

D3B4S8JA: DescriptionSnap Acting/Limit Switch, SPST, Momentary, 2.5mm, Solder Terminal, Straight Type Actuator, Panel Mount,; CategoryMechanical and electronic products switch; File Size257KB，3 Pages; ManufacturerThe Cherry Corporation

Download Datasheet Parametric View All

D3B4S8JA Overview

Snap Acting/Limit Switch, SPST, Momentary, 2.5mm, Solder Terminal, Straight Type Actuator, Panel Mount,

D3B4S8JA Parametric

Parameter Name	Attribute value
Maker	The Cherry Corporation
Reach Compliance Code	compliant
ECCN code	EAR99
Actuator stroke	2.5 mm
Actuator type	STRAIGHT TYPE
body width	10.3 mm
body height	15.9 mm
Body length or diameter	27.8 mm
Contact (AC) maximum rated R load	10A@250VAC
Maximum contact current (AC)	10 A
Maximum contact voltage (AC)	250 V
Electrical life	10000 Cycle(s)
Manufacturer's serial number	D3
Installation features	PANEL MOUNT
Maximum operating force	550 N
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
Maximum pre-travel	1.9 mm
surface mount	NO
Switch action	MOMENTARY
switch function	SPST
Switch type	SNAP ACTING/LIMIT SWITCH
Termination type	SOLDER

Preview

Download Datasheet

View All

MINIATURE

D3 Series

Features

Self-cleaning effect of wiping contact

mechanism provides excellent reliability

Suitable for low actuation speeds

Highly flexible, due to

two mounting positions and a

variety of auxiliary actuators

Wide variety of terminal types

> 3mm (0.12″) contact gap available

Stainless steel spring

NC terminal

NO terminal

POM actuating button

PET cover and base

Silver contacts

Common terminal

Electrical Ratings

Switch

Series

EN61058 Rating

UL1054 Rating

Electrical Life at Rated Load

According to EN

According to UL

(Min. Operations)

D38 – Std.

16(4)A, 250V~

10(3)A, 400V~

16A, 125/250VAC, 1HP

50,000

6,000

Specifications

Electrical

Temperature Rating:

Flammability Rating:

Materials

-40° to +85°C

UL94V-O

PET

POM

Stainless Steel; Nickel-Plated Steel

Copper-Zinc

Silver Cadmium Oxide

Case:

Actuator:

Auxiliary Actuator:

Terminals:

Contacts:

PET = Polyethyleneterephthalate • POM = Polyacetal

Recommended Resources

Robot sound generator

Photoelectric detection output control circuit

Tolerance circuit for resistor determination using window discriminator

Power supply circuit diagram of AST-TE1498 multi-frequency color display

Two tube medium wave wireless microphone circuit

Typical application circuit buck circuit diagram of LT1111

Please advise on the practical application of lm324n: I want to use lm324n to realize 10mv-20mv voltage comparison and output it to the lcd to light up. No output is less than 10mv and greater than 20mv. I am a novice asking for advice. Thank you....; aimboy Analog electronics

On the problem of DC in AD sampling signal: I recently encountered such a problem during circuit debugging.System Description:The DDS core in the FPGA is used to generate a sine wave signal with a frequency of several hundred Hz, which is conve...; tsw_0_0_0 DSP and ARM Processors

"Operational Amplifier Noise Optimization Handbook" Reading Notes: Jump Noise: [i=s]This post was last edited by dontium on 2015-1-23 11:46[/i] Determination of jump noise: From the perspective of time domain, the time domain model of jump noise does not conform to Gaussian dist...; azhiking Analogue and Mixed Signal

ZwSetInformationFile deletes the FileInformationClass value of a file: I want to monitor the deletion of files, and I hooked ZwSetInformationFile, but I found that when I use Shift+Delete to delete files, the value of FileInformationClass is FileDispositionInformation, b...; sunyitui Embedded System

Looking for a switching power supply solution for power amplifier TDA2030a (about ±15V, about 30W power): An amplifier drives a 4 ohm speaker. The amplifier uses TDA2030a, the supply voltage is ±15V, the output power is 20W, and the output current is about 3.5A. I hope the master can provide a switching p...; 紫龙二号 Power technology

How to realize automatic switching of input method in WINCE?: Now I have a Japanese input method in my WINCE environment, but there are several input methods in the Japanese input method, such as direct English input, full-width flat input, half-width flat input...; awwwcwwxf Embedded System

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components