Pins designated as "NC" are typically unbonded pins. However some of them are bonded for special testing purposes. Hence if a signal is applied to these pins, care
should be taken that the voltage applied on these pins does not exceed the V
CC
applied to the device. This will ensure proper operation.
Ordering Information
FM
93
C
XX
A
T
LZ
E
XXX
Package
N
M8
MT8
None
V
E
Blank
L
LZ
Blank
T
A
Density
46
C
CS
Interface
93
Letter Description
8-pin DIP
8-pin SO
8-pin TSSOP
0 to 70°C
-40 to +125°C
-40 to +85°C
4.5V to 5.5V
2.7V to 5.5V
2.7V to 5.5V and
<1µA Standby Current
Normal Pinout
Rotated Pinout
x8 or x16 configuration
1024 bits
CMOS
Data protect and sequential
read
MICROWIRE
Temp. Range
Voltage Operating Range
Fairchild Memory Prefix
2
FM93C46A Rev. C.1
www.fairchildsemi.com
FM93C46A 1K-Bit Serial CMOS EEPROM
(MICROWIRE
TM
Synchronous Bus)
Absolute Maximum Ratings
(Note 1)
Ambient Storage Temperature
All Input or Output Voltages
with Respect to Ground
Lead Temperature
(Soldering, 10 sec.)
ESD rating
-65°C to +150°C
+6.5V to -0.3V
Operating Conditions
Ambient Operating Temperature
FM93C46A
FM93C46AE
FM93C46AV
Power Supply (V
CC
)
0°C to +70°C
-40°C to +85°C
-40°C to +125°C
4.5V to 5.5V
+300°C
2000V
DC and AC Electrical Characteristics
V
CC
= 4.5V to 5.5V unless otherwise specified
Symbol
I
CCA
I
CCS
I
IL
I
OL
I
ILO
V
IL
V
IH
V
OL1
V
OH1
V
OL2
V
OH2
f
SK
t
SKH
t
SKL
t
CS
t
CSS
t
DH
t
DIS
t
CSH
t
DIH
t
PD
t
SV
t
DF
t
WP
Parameter
Operating Current
Standby Current
Input Leakage
Output Leakage
Input Leakage ORG Pin
Input Low Voltage
Input High Voltage
Output Low Voltage
Output High Voltage
Output Low Voltage
Output High Voltage
SK Clock Frequency
SK High Time
SK Low Time
Minimum CS Low Time
CS Setup Time
DO Hold Time
DI Setup Time
CS Hold Time
DI Hold Time
Output Delay
CS to Status Valid
CS to DO in Hi-Z
Write Cycle Time
Conditions
CS = V
IH
, SK=1.0 MHz
CS = V
IL
V
IN
= 0V to V
CC
(Note 2)
ORG tied to V
CC
ORG tied to V
SS
(Note 3)
Min
Max
1
50
±-1
Units
mA
µA
µA
µA
V
V
V
MHz
ns
ns
ns
ns
ns
ns
ns
ns
-1
-2.5
-0.1
2
1
2.5
0.8
V
CC
+1
0.4
I
OL
= 2.1 mA
I
OH
= -400
µA
I
OL
= 10
µA
I
OH
= -10
µA
(Note 4)
0°C to +70°C
-40°C to +125°C
2.4
0.2
V
CC
- 0.2
1
250
300
250
(Note 5)
250
50
70
100
0
20
500
500
ns
ns
ns
ms
CS = V
IL
100
10
3
FM93C46A Rev. C.1
www.fairchildsemi.com
FM93C46A 1K-Bit Serial CMOS EEPROM
(MICROWIRE
TM
Synchronous Bus)
Absolute Maximum Ratings
(Note 1)
Ambient Storage Temperature
All Input or Output Voltages
with Respect to Ground
Lead Temperature
(Soldering, 10 sec.)
ESD rating
-65°C to +150°C
+6.5V to -0.3V
Operating Conditions
Ambient Operating Temperature
FM93C46AL/LZ
FM93C46ALE/LZE
FM93C46ALV/LZV
Power Supply (V
CC
)
0°C to +70°C
-40°C to +85°C
-40°C to +125°C
2.7V to 5.5V
+300°C
2000V
DC and AC Electrical Characteristics
V
CC
= 2.7V to 4.5V unless otherwise specified. Refer to
page 3 for V
CC
= 4.5V to 5.5V
Symbol
I
CCA
I
CCS
Parameter
Operating Current
Standby Current
L
LZ (2.7V to 4.5V)
Input Leakage
Output Leakage
Input Leakage ORG Pin
Input Low Voltage
Input High Voltage
Output Low Voltage
Output High Voltage
SK Clock Frequency
SK High Time
SK Low Time
Minimum CS Low Time
CS Setup Time
DO Hold Time
DI Setup Time
CS Hold Time
DI Hold Time
Output Delay
CS to Status Valid
CS to DO in Hi-Z
Write Cycle Time
Conditions
CS = V
IH
, SK=250 KHz
CS = V
IL
Min
Max
1
10
1
Units
mA
µA
µA
µA
µA
V
V
KHz
µs
µs
µs
µs
ns
µs
ns
µs
µs
µs
µs
ms
I
IL
I
OL
I
ILO
V
IL
V
IH
V
OL
V
OH
f
SK
t
SKH
t
SKL
t
CS
t
CSS
t
DH
t
DIS
t
CSH
t
DIH
t
PD
t
SV
t
DF
t
WP
V
IN
= 0V to V
CC
(Note 2)
ORG tied to V
CC
ORG tied to V
SS
(Note 3)
-1
-2.5
-0.1
0.8V
CC
I
OL
= 10µA
I
OH
= -10µA
(Note 4)
0.9V
CC
0
1
1
1
0.2
70
0.4
0
0.4
±1
1
2.5
0.15V
CC
V
CC
+1
0.1V
CC
250
(Note 5)
2
1
CS = V
IL
0.4
15
Capacitance
T
A
= 25°C, f = 1 MHz or
250 KHz (Note 6)
Symbol
C
OUT
C
IN
Note 1:
Stress above those listed under “Absolute Maximum Ratings” may cause permanent damage
to the device. This is a stress rating only and functional operation of the device at these or any other
conditions above those indicated in the operational sections of the specification is not implied. Exposure
to absolute maximum rating conditions for extended periods may affect device reliability.
Note 2:
Note 3:
Typical leakage values are in the 20nA range.
ORG pin may draw >1µA when in x8 mode due to the internal pull-up transistor.
Test
Output Capacitance
Input Capacitance
Typ
Max
5
5
Units
pF
pF
Note 4:
The shortest allowable SK clock period = 1/f
SK
(as shown under the f
SK
parameter). Maximum
SK clock speed (minimum SK period) is determined by the interaction of several AC parameters stated
in the datasheet. Within this SK period, both t
SKH
and t
SKL
limits must be observed. Therefore, it is not
allowable to set 1/f
SK
= t
SKHminimum
+ t
SKLminimum
for shorter SK cycle time operation.
Note 5:
CS (Chip Select) must be brought low (to V
IL
) for an interval of t
CS
in order to reset all internal
device registers (device reset) prior to beginning another opcode cycle. (This is shown in the opcode
diagram on the following page.)
Note 6:
This parameter is periodically sampled and not 100% tested.
[size=14px]Electrolytic capacitors are one of the main components that affect switching power supplies, but most people use static offline testing to test electrolytic capacitors. This cannot truly re...
Atmel 8-bit AVR Product Overview : https://training.eeworld.com.cn/course/75?From the perspective of ease of use, low power consumption and high integration, Atmel AVR 8-bit and 32-bit microcontroller...
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
When choosing a laptop battery, you should consider several factors, such as power, appearance, and quality.
Regarding power, we often see that a manufacturer uses values such as the number ...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
5. Identifiers and keywords of C language
A complete PIC microcontroller C language program usually consists of six parts: include files (i.e. header files 1, variable definitions, variable de...[Details]
12v Lead Acid batteries used in trucks, cars, RVs and uninterruptible power supplies are usually rated at 12V. This circuit monitors the battery, the charge and discharge curves, gives the cu...[Details]
Abstract: In recent years, with the establishment and grid-connected power generation of a large number of solar photovoltaic power stations at home and abroad, photovoltaic grid-connected inverter...[Details]
LED technology has made rapid progress, and improvements in chip design and materials have promoted the development of brighter and more durable light sources, and the scope of light source applica...[Details]
Since AC mains power may experience power outages, voltage sags and surges, continuous undervoltage and overvoltage, and frequency fluctuations during supply, these factors will affect the continuous ...[Details]
introduction
Steam turbines are driven by high-temperature and high-pressure steam generated by boilers to run at high speed. They are key power equipment in thermal power plants. The emergenc...[Details]
0 Introduction
In order to improve the automation control of shortwave transmitters, so that they can automatically process from far to near, the technicians here use the ICS system to complete the ...[Details]
As the global LED market demand continues to increase, my country's LED industry will face huge opportunities in the future. However, the core LED technology and patents are basically monopolized b...[Details]
This article discusses the six design steps of LED lighting system design in detail: (1) determine the lighting requirements; (2) determine the design goals and estimate the optics; (3) the efficie...[Details]
Among the uses of electrical energy, lighting accounts for a considerable proportion. Compared with the earlier ordinary incandescent lamps, the fluorescent lamps and energy-saving lamps we commonl...[Details]
Movpower is a portable power bank. It can charge most mobile phones and digital products, such as digital cameras, PDAs, and mobile phones such as Apple, iPod, Blackberry, Motorola, Samsung, Nokia,...[Details]
There are many types and styles of digital voltmeters in design and development. Traditional digital voltmeters have their own characteristics. They are suitable for manual measurement on site. Tra...[Details]
Talking about work
京公网安备 11010802033920号
EEWORLD
